• 한국항공우주학회지
• /
• 제41권9호
• /
• pp.714-719
• /
• 2013

본 연구 대상 터보 프롭 항공기는 주어진 항공기 임무 수행을 위해 결빙 조건하에서도 운용이 가능하여야 한다. 동 연구에 적용된 터보 항공기의 공기 흡입구 계통은 정상 비행조건하에서 엔진 입구에 최대 전압력을 공급할 수 있도록 설계 및 검증이 되어야 할 뿐만 아니라 결빙조건하에서 생길 수 있는 얼음과 같은 입자가 엔진 흡입구 망으로 들어가서 엔진 화염꺼짐이나 엔진에 심각한 손상을 주지 않도록 하기 위한 관성분리기를 포함하도록 개발이 되어야 한다. 따라서 결빙 조건하에서 형상이 변하는 가변형상의 공기흡입구 조립체를 설계하고 설계 결과 확인을 위해 조립체에 대한 전산 유동 및 구조해석을 수행하였다. 이후 35% 축소형 모델을 제작하여 풍동시험을 수행하였다. 동 논문에서는 흡입구 조립체 개발과정에서 요구되는 공기역학적 설계, 잔산 유동/구조 해석 및 풍동 시험평가 결과를 기술하였다.

• 한국유체기계학회 논문집
• /
• 제15권4호
• /
• pp.27-32
• /
• 2012

Gas turbines for an aircraft have the start and restart capabilities within their flight envelop. It is an important item for engine qualification and substantiated with the test. Experimental investigations were carried out to find the relation between the corrected torque and the corrected rotating speed of an air turbine starter in this study. A dedicated air supply system for the air turbine starter and a special device to measure the torque and the rotating speed of the air turbine starter were developed and installed at the altitude engine test facility in Korea Aerospace Research Institute. Experimental results show that the relations between the corrected torque and the corrected rotating speed of the air turbine starter are linear and the inlet temperature and pressure conditions for the air turbine starter were found out to provide minimum required torque for the engine qualification test at various altitude. The start and restart tests for the currently developing engine were successfully performed using this experimental results.

• 한국자동차공학회논문집
• /
• 제11권6호
• /
• pp.21-29
• /
• 2003

Boosting of engine power by using Turbo- or Super-charger is a solution to comply with $CO_2$-regulation in Europe. Turbo-charger is now playing a major role in the field of charging system thank to its technical advantages such as no demand of operation power from engine. A mechanically driven Super-charger, however, is now popular due to quick speed response to change of the driving mode-high engine torque even at low engine speed. Since Super-charger needs operation power from engine, it is difficult to improve its relatively higher fuel consumption than that of Turbo-charger. This negative point is still an obstacle to the wide use of Super-charger. This study aims to develop power control concept to achieve the minimization of operation power when it is not necessary to charge at idling or part load driving condition. A screw type Super-charger was modified in design partially and adapted an internal bypass valve and a bypass tube to control charging pressure at part load. The various control concepts show a possibility to reduce operation power of Super-charger and result in improvement of fuel consumption.

• 한국자동차공학회논문집
• /
• 제9권6호
• /
• pp.94-102
• /
• 2001

The thermodynamic second law analysis, which means available energy or exergy analysis, for the indicated performance of Otto cycle engine has been carried out. Each operating process of the engine is simplified and modeled into the thermodynamic cycle. The calculation of the lost work and exergy through each process has been done with the thermodynamic relations and experimental data. The experimental data were measured from the test of single cylinder Otto cycle engine which operated at 2500 rpm, WOT(Wide Open Throttle) and MBT(Minimum advanced spark timing for Best Torque) condition with different fuels: gasoline, methanol and mixture of butane-methanol called M90. Experimental data such as cylinder pressure, air and fuel flow rate, exhaust gas temperature, inlet gas temperature and etc. were used for the analysis. The proposed model and procedure of the analysis are verified through the comparison of the work done in the study with experimental results. The calculated results show that the greatest lost work is generated during combustion process. And the lost work during expansion, exhaust, compression and induction process follows in order.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.492-498
• /
• 2008

In this paper are described recent studies about variable nozzles, that are a rectangular type nozzle and an axisymmetric type nozzle, of the precooled turbojet engine(S-engine) which are developed for the demonstration of the key technologies for the propulsion system of the hypersonic airplane and the first stage propulsion of the TSTO space plane. For the rectangular nozzle, three types of C-shaped carbon/carbon composite cowls which includes subscale model of the precooled turbojet engine are fabricated and the fine attachment to the ramp is confirmed. For the firing of the S-engine, stainless steel cowl with concrete heat insulator are fabricated and tested for 20 sec. Axisymmetric variable plug nozzle which is made of C/C material is fabricated and pressurized by the cold flow test. The axisymmetric plug nozzle can be operative up to 0.57 MPa of nozzle inlet pressure.

• 한국유체기계학회 논문집
• /
• 제9권2호
• /
• pp.25-29
• /
• 2006

Computational and experimental studies on the forward-sweep inducer for the rocket-engine turbopump are presented in comparison with the conventional backward-sweep inducer. Computational results show that back flows at the inlet decrease in the case of forward-sweep inducers compared to the back-ward inducer. Moreover, the low pressure region at the back flow is decreased, which is presumed to improve the suction performance of the inducers. Experimental results show that the suction performance of the forward-sweep inducer is almost the same as that of the backward-sweep inducer although it has smaller inlet tip diameter and shorter length. The efficiency of the forward-type inducer is found better than that of the backward-sweep inducer due to the small size of back flows.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2005년도 연구개발 발표회 논문집
• /
• pp.650-654
• /
• 2005

Computational and experimental studies on the forward-sweep inducer for the rocket-engine turbopump are presented in comparison with the conventional backward-sweep inducer. It is shown that back flows at the inlet decreases for forward-sweep inducers. And the low pressure region at the back flow are also decreased, which is assumed to promote the suction performance of the inducers. The backward-sweep inducer shows almost the same suction performance as that of the backward-sweep inducers although it has small inlet tip diameter and shorter length. And the efficiency of the forward-type inducer shows better results than the backward-sweep inducer due to the small size of backflows.

• 한국추진공학회지
• /
• 제21권3호
• /
• pp.49-55
• /
• 2017

가스터빈엔진의 성능시험을 위한 엔진 입구덕트를 1D 기법으로 Sizing 하였으며, 압축기 입구유동측정면(AIP, Aerodynamic interface plane)에서 경계층 두께를 최소화하고, 코어부 마하수분포가 균일하도록 설계하였다. 노즈콘 형상은 Haack-series 모델을 적용하고, 덕트 안쪽과 바깥쪽 면적변화율이 동일하도록 입구덕트 채널 바깥반경($r_o$)를 결정하여 설계목적을 구현하고자 하였으며, 이러한 형상이 설계목표에 부합하는지 확인하기 위하여 CFD를 수행하였다. AIP면에서 정압력분포는 최대값과 최소값 차이가 0.16% 이었으며, 마하수분포에서 경계층은 덕트반경 길의 2% 이내로 설계목표를 만족하였다. 이때 균일유동 코어부는 채널높이의 95% 이상이었다. 또한 입구유동의 전온도를 측정하기 위한 키엘 전 온도레이크 위치는 온도 회복계수가 최대화 되도록 마하수가 0.1 이하 지역인 노즈콘 전방 100 mm 이내이어야 함을 확인하였다.

• 한국유체기계학회 논문집
• /
• 제20권2호
• /
• pp.53-62
• /
• 2017

In this paper, the effect of oil conditions in rotor dynamic behaviors of a FFRB (Fully-Floating Ring Bearing) is investigated. Through the characteristic of a FFRB has two films, it has several advantages such as less friction loss and better stability over a wide speed range. However, it is difficult to supply a oil to the inner film. Thus, turbocharger makers have been paid significant attention to the lubrication of a FFRB because of its importance. This work focuses on the influence of oil inlet pressure and temperature. The methodologies of computational simulation and experimental test were used to estimate the rotor dynamic behaviors. In experimental test, the single-scroll turbocharger for the 1.4L diesel engine was used. The results show that the oil inlet pressure and temperature will place considerable influence on the rotor response. Oil conditions affect RSR (Ring Speed Ratio) which is cause of sub-synchronous vibrations, which also cause of oil whirling and whip even a critical speed. At higher speed range, the phenomenon of self-excited vibrations which is cause of instability of fluid whirl is investigated through the orbit shapes that consist of small orbit and large amplitude orbit. It is shown that some performance of a FFRB can be controlled by the conditions of oil supply. Finally, it was revealed that the oil induced operating conditions will strongly affect the turbocharger rotor dynamics behaviors.

• 한국추진공학회지
• /
• 제4권4호
• /
• pp.87-97
• /
• 2000

국내에서 최초로 개발된 기본훈련기 KT-1의 추진기관인 터보프롭 엔진(PT6A-62)을 위한 정상상태 성능모사 덴 진단 프로그램을 개발하였다. 개발된 정상상태 성능해석 프로그램의 검증을 위해 해석 결과를 엔진 제작사에서 제공한 성능 데이터 및 가스터빈 엔진의 성능 모사 프로그램으로 잘 알려진 GASTURB와 비교하였다. 개발된 정상상태 성능해석 프로그램의 검증을 위해 해석 결과를 엔진 제작사에서 제공한 성능 데이터 및 가스터빈 엔진의 성능 모사 프로그램으로 잘 알려진 GASTURB와 비교하였다. 개발된 프로그램의 유용성을 검증하기 위해 다양한 고도, 비행마하수, 부분부하에서의 성능을 해석하였다. GPA(Gas Pess Analysis) 방법은 엔진의 성능 저하를 구성품 효율의 저하와 공기유량의 변화량으로 나타내는 방법이다. 오염, 부식, 침식과 같은 물리적 손상을 탐지하기 위한 최적의 계측변수 선정을 위해 GPA 방법은 유용하다. 본 연구에서는 최적의 계측변수를 선정하기 위해 2가지 방법을 이용하였다 하나는 독립변수의 수를 다르게 하여 계측기 수가 진단에 미치는 영향을 알아보았으며 다음 종속변수의 종류가 미치는 영향을 살펴보았다. 해석 결과에 따르면 압축기 입구 온도 및 압력, 압축기 터빈 입구 온도 및 압력, 동력 터빈 입구의 온도 및 압력과 축마력, 연료유량 등을 측정하여 진단에 이용하는 것이 가장 오차가 적었다.