• 드라이브 ㆍ 컨트롤
• /
• 제14권1호
• /
• pp.29-34
• /
• 2017

This study analyzed a life test method for a power take-off (PTO) gearbox. An engine transfers mechanical power (rotation and torque) to a hydraulic pump through a PTO Gearbox with one input shaft and three output shafts. PTO gear box durability under high loads over long time periods was tested using dynamometers. In order to reflect the rated operating conditions, power must be distributed to each output shaft, and experiments were conducted under various conditions to verify the characteristics of the distributed power. An accelerated life test was designed using speed and torque as acceleration factors. Also, efficiency tests were conducted under various load conditions. Also, a lubrication oil composition analysis was performed to analyze gearbox wear status.

• 한국철도학회논문집
• /
• 제8권1호
• /
• pp.87-92
• /
• 2005

Numerous advance studies usually have focused on preventing human error through mechanization and automation; however, this study. by connecting with accidents caused by careless handling on the basis of the present aptitude test, aims at investigating an improving plan for the railroad safety management system. To attain this purpose, present situation and point at issue of the aptitude test were surveyed through the questionnaire. Through this research, the aptitude test on railroad safety might be systematically improved by reforming some institutional issues.

• Journal of Power Electronics
• /
• 제13권1호
• /
• pp.77-85
• /
• 2013

This paper proposes a new dead time compensation method of independent six-phase permanent magnet synchronous motors (IS-PMSM). The current of the independent phase machines contains odd-numbered harmonics because of the dead time and the nonlinear characteristics of the switching devices. By using the d-q-n three-dimensional vector analysis, these harmonics can be extracted at the n-axis current. Thus, the current distortion can be compensated by controlling the n-axis current of the IS-PMSM to zero. The proposed method is simple and can be easily implemented without additional hardware setup. The validity of the proposed compensation method is verified with simulations and several experiments.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2015년도 전력전자학술대회 논문집
• /
• pp.233-234
• /
• 2015

전기추진선박의 엔진발전기를 부하에 따라 가변속 운전하면 일정속도로 운전하는 것보다 연료를 절약할 수 있다. 내연 기관 엔진은 저속 운전 시 속도 리플로 인하여 운전이 불안정해지므로 저속 운전에 한계가 있다. 또 발전기 조속기의 느린 응답으로 속도 리플이 발생하기도 한다. 본 논문에서는 배터리 에너지 저장 장치를 이용하여, 과도 상태에서의 속도 리플을 감소시키는 제어 방식을 제안하여 가변속 엔진의 운전 범위를 넓히고자 한다.

• 한국정밀공학회지
• /
• 제13권3호
• /
• pp.132-140
• /
• 1996

This paper developes a torsional vibration model of heavy duty truck drive line for simulation of a driving rattle, which causes very annoying noise to driver at the full load driving condition. Test results show a peak in the fit plots at the frequency of the 2nd harmonics of propeller shaft revolution. A 10 d.o.f. lumped parameter nonlinear torsional vibration model is constructed and engine torque variation is calculated from P- .theta. diagram. Time responses are simulated and compared with the test results, which show fairly good agreement. The effects of paramenter change are investigated, and the optimum configuration is proposed.

• 한국정밀공학회지
• /
• 제14권2호
• /
• pp.74-83
• /
• 1997

The non-periodic angular accelerations of engine are the major cause of gear rattle. This gear rattle is based on the existence of a backlash between the drive gear of input shaft and the free gear of output shaft in the gearbox. Especially, the neutral gear rattle have a very bad effect on the ride quality. Test-rig was constructed in order to evaluate the parameter influence upon the neutral gear rattle. Also, each different 4 type torsional characteristic of clutch was manufactured. Experimental conditions are the use of each different 4 type torsional characteristic of clutch and oil temperature variation in gearbox. In case of the same stiffiness of pre-damper type clutch at idling, the clutch of large hysteresis showed dam- ping effects at the 2nd input gear and the 2nd output gear. Also, the main-damper type clutch was shown to large resonance phenomenon at the 2nd input gear. Accordingly, main-damper type clutch was unapp- roriate at idling.

• 전력전자학회논문지
• /
• 제26권4호
• /
• pp.263-270
• /
• 2021

Active AC/DC converters with PWM operation are utilized to regulate rectified DC bus voltage of a permanent magnet synchronous generator in the maritime DC power system. A DC bus voltage regulation strategy that exploits the six-step operation is proposed in this study. Compared with that of the PWM operation, switching loss of the converter can be significantly reduced under the six-step operation. Moreover, conduction loss can also be reduced due to the high modulation index and reduced flux-weakening current of the six-step operation. A controller is used for the proposed DC bus voltage regulation strategy to verify its validity with the simulation and experimental setup. The simulation and the experimental test results showed that the converter loss reduces to a maximum of 70% and 19%, respectively.

• 로봇학회논문지
• /
• 제17권4호
• /
• pp.477-483
• /
• 2022

In this paper, we propose waste collection vehicle system with a safety device for worker safety and an autonomous driving function. The steering system is applied as MDPS (Motor Drive Power Steering) system to control the waste collection vehicle of the internal combustion engine. Safety-related errors is prevented through redundancy brake of the integrated system and the control braking system. In order to ensure safety between workers and waste collection vehicles, work guidelines and safety devices for emergency stop in case of danger are applied to vehicles. In addition, this research is conducted on improving the working efficiency through vehicle condition monitoring system and a short-range control system for field test. This research is aimed to secure stability through demonstration and contribute to the industrialization of unmanned waste collection vehicles.

• 한국정밀공학회지
• /
• 제12권12호
• /
• pp.139-148
• /
• 1995

In this paper an electro-hydraulic servo system is designed by using a fuzzy control algorithm. In order to drive an optimal fuzzy control system, a simulation program for the control system has been developed. By this program the fuzzifier and defuzzifier, a fuzzy inference method, a fuzzy relational matrix, and a fuzzy inference method are investigated. As a result, Larsen inference method, 9*9 fuzzy relational matrix, and center of area defuzzifier are turned out the best as parameters. Finally this method is compared with the conventional PID algotithm, and showed that the fuzzy control performs better than PID algorithm. The fuzzy control performs very well adap- tation against uncertain disturbances.

• 한국시뮬레이션학회논문지
• /
• 제32권4호
• /
• pp.77-84
• /
• 2023

농업 분야에서도 내연기관 트랙터에서 벗어나 전기 트랙터 및 수소 트랙터와 같은 대체 에너지원을 사용하는 동력원이 개발되고 있다. 기존의 내연기관 트랙터에서 사용되던 엔진 및 변속기와 같은 부품들이 모터와 배터리 등으로 교체되면서 무게중심이 변화하게 되며, 이에 따라 전도 위험성을 새로이 고려해야 한다. 이 연구의 목적은 동역학 시뮬레이션을 통해 전기 트랙터의 주요 부품 위치별 전도 각도를 분석하여 전도 사고를 최소화하고 안정성을 향상하기 위한 부품 최적의 배치를 도출하는 것이다. PTO 모터, 구동 모터와 배터리 팩의 구성 수준 3가지와 배치 방법 3가지 요인으로 실험 설계하여 총 9가지 동역학 시뮬레이션을 진행하였다. 실험 결과, 구동 모터와 PTO 모터를 트랙터 앞쪽과 뒤쪽에 각각 위치하고 두 개의 배터리 팩을 트랙터 중간에 위치시킨 Type 3 Level 3가 전도 각도가 높은 것을 확인하였다. 본 연구 결과 무게중심을 뒤쪽으로 배치할수록, 아래에 위치할수록 안정성이 증가하였다. 향후 연구로는 부품의 성능과 배치 효율성을 고려한 부품의 최적 위치를 찾는 연구가 필요하다.