• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.773-778
• /
• 2001

This paper describes the implementation of the vector control schemes for a variable-speed 131kW PMSM (Permanent Magnet Synchronous Motor) in super-high speed application. The vector control with synchronous reference frame current regulator has been implemented with the challenging requirements such as the extremely low stator inductance$(28^{\mu}H)$, the high dc link voltage(600V) and the high excitation frequency(1.2kHz). Because the conventional position sensor is not reliable in super-high speed, a vector control scheme without any position sensor has been proposed. The proposed sensorless algorithm is implemented by processing the output voltage of the PI current regulator, and hence the structure is simple and the estimated speed is robust to the measurement noise. The experimental system has been built and the proposed control has been implemented and evaluated. The test result, up to the speed of 60,000 r/min, shows the validity of the proposed control.

• 전기학회논문지P
• /
• 제64권4호
• /
• pp.231-235
• /
• 2015

Bimodal Tram developed by KRRI is driven by a series Hybrid propulsion system which has both the CNG engine, generator and LPB(Lithium Polymer Battery) pack. It has three driving modes; Hybrid mode, Engine mode and Battery mode. Even in case of Battery mode, LPB pack to get enough power to drive the vehicle only by itself onsists of 168 LPB cells(80Ah per lcell), 650V. It is important thing to manage LPB pack in a right way, which will extend the lifetime of LPB cells and operate in the hybrid mode effectively. This paper has shown the development of battery management system(12 BMS, 1 BMS per 14cells) to manage LPB pack which is connected with CAN(Controller Area Network) each other and measure the voltage, current, temperature and also control the cooling fan inside of LPB pack. Using the measured data, BMS can show the SOC(State of Charge), SOH(State of Health) and other status of LPB pack including of the cell balancing.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.59-64
• /
• 2018

In general, tracked combat vehicles require excellent output performance of a power unit system to drive on special terrains and in extreme environmental conditions. However, high temperature and pressure are readily applied to the coolant hose in the power unit of the vehicles during high-speed driving under extreme road and weather conditions. These driving conditions can cause the separation phenomenon of the coolant hose in the power unit and consequentially engine overheating during driving. Therefore, a newly designed decompression device for the coolant hose has been proposed and manufactured to solve these problems in the present study. To validate of the newly proposed decompression device, the input and output pressures were measured under the before- and after-improvement conditions using experimental methods for different engine RPMs. In addition, the pre-heater temperature was measured under both conditions. From the experimental results, we expect that the current investigation can help to improve the driving performance of tracked combat vehicles.

• International Journal of Automotive Technology
• /
• 제8권6호
• /
• pp.781-790
• /
• 2007

Hybrid electric vehicles(HEV) combined with more than one power sources have great potential to improve fuel economy and reduce pollutant emissions. The Integrated Starter Generator(ISG) HEV researched in this paper is a two energy sources vehicle, with a conventional internal combustion engine(ICE) and an energy storage system(batteries). In order to investigate the potential of diesel engine hybrid electric vehicles in fuel economy improvement and emissions reduction, a Dynamic Programming(DP) based supervisory controller is developed to allocate the power requirement between ICE and batteries with the objective of minimizing a weighted cost function over given drive cycles. A fuel-economy-only case and a fuel & emissions case can be achieved by changing specific weighting factors. The simulation results of the fuel-economy-only case show that there is a 45.1% fuel saving potential for this ISG HEV compared to a conventional transit bus. The test results present a 39.6% improvement in fuel economy which validates the simulation results. Compared to the fuel-economy-only case, the fuel & emissions case further reduces the pollutant emissions at a cost of 3.2% and 4.5% of fuel consumption with respect to the simulation and test result respectively.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.38-47
• /
• 2005

In this paper, a regenerative braking algorithm is proposed to make the maximum use of the regenerative braking energy for an independent front and rear motor drive parallel HEV. In the regenerative braking algorithm, the regenerative torque is determined by considering the motor capacity, motor efficiency, battery SOC, gear ratio, clutch state, engine speed and vehicle velocity. To implement the regenerative braking algorithm, HEV powertrain models including the internal combustion engine, electric motor, battery, manual transmission and the regenerative braking system are developed using MATLAB, and the regenerative braking performance is investigated by the simulator. Simulation results show that the proposed regenerative braking algorithm contributes to increasing the battery SOC, which recuperates 60 percent of the total braking energy while satisfying the design specification of the control logic. In addition, a control algorithm which limits the regenerative braking is suggested by considering the battery power capacity and dynamic response characteristics of the hydraulic control module.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.341-345
• /
• 2005

본 논문은 액체로켓엔진용의 약 1.5MW급 터빈을 구동할 수 있고, 액체산소와 케로신을 추진제로 하는 연료과잉 영역에서 작동하는 실물형 가스발생기의 고압연소특성에 대한 것이다. 실물형 가스발생기 개발과정의 개략적인 과정, 연소시험 결과 분석에 따른 혼합비와 온도관계식, 연소가스의 물성치인 분자량 및 비열비 등에 대한 내용을 기술하였다. 혼합비에 따른 온도관계식을 고압에서 새롭게 얻을 수 있었으며 연소가스의 분자량 및 비열비를 수정하고 유량관계식을 통해 이들의 타당성을 확인하였다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2000년도 유체기계 연구개발 발표회 논문집
• /
• pp.145-152
• /
• 2000

A turbopump system composed of two pumps and one turbine is considered. The turbine composed of a nozzle and a rotor is used to drive the pumps while gas passes through the nozzle, potential energy is converted to kinematic energy, which forces the rotor blades to spin. In this study, an aerodynamic design of turbine system is investigated using compressible fluid dynamic theories with some pre-determined design requirements (i.e., pressure ratio, rotational speed, required power etc.) obtained from liquid rocket engine (L.R.E.) system design. For simplicity of turbine system, impulse-type rotor blades for open type L.R.E. have been chosen. Usually, the open-type turbine system requires low mass flow rate compared to close-type system. In this study, a partial admission nozzle Is adopted to maximize the efficiency of the open-type turbine system. A design methodology of turbine system has been introduced. Especially, partial admission nozzle has been designed by means of simple empirical correlations between efficiency and configuration of the nozzle. Finally, a turbine system design for a 10 ton thrust level of L.R.E is presented.

• 한국추진공학회지
• /
• 제7권4호
• /
• pp.19-26
• /
• 2003

본 논문에서는 팁제트 로터를 사용한 CRW 비행체의 추진시스템에 대한 개념연구 결과를 다루었다. 비행체 중앙에 위치한 엔진으로부터 배기가스를 로터나 주 추력노즐까지 공급하기 위해서 길고 복잡한 내부덕트 시스템이 필요하며 배기가스 분배장치 등이 필요하다. 추진시스템의 성능해석을 위해 엔진운전특성과 내부덕트 시스템 특성을 함께 해석하였다 본 연구에서는 회전익모드에서 내부덕트 시스템의 형상변화에 따른 엔진 및 전체 추진시스템의 운전특성을 분석하여 추진시스템 설계를 위한 중요설계변수를 도출하였으며 파라매트릭 연구를 수행하여 향후 설계방향설정에 기여하였다.

• 한국전자통신학회논문지
• /
• 제13권2호
• /
• pp.443-448
• /
• 2018

최근 이산화탄소에 따른 지구온난화 문제와 배기가스의 저감을 위하여 하이브리드 자동차가 각광을 받고 있다. 하이브리드 자동차는 기계적인 엔진과 전기적인 모터시스템이 결합된 동력구조를 갖는다. 차량의 주행조건에 따라 하이브리드 자동차의 구동을 위해 필요로 하는 에너지의 흐름은 달라진다. 본 논문에서는 실시간 모니터링 시스템을 이용한 하이브리드 자동차 교육용 콘텐츠에 관한 연구를 대상으로 한다. 하드웨어와 버추얼 프로그램으로 구성된 실시간 모니터링 시스템을 이용하여 하이브리드 자동차의 전체적인 운행을 주행조건별로 시뮬레이션을 통해 모사하고, 하드웨어를 통해 학습할 수 있는 방법에 대해 기술한다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1251-1256
• /
• 2014

The use of lubrication oil is of many purposes and one among them is to drive the engine mounted on a ship. Hence the supply of clean lubrication oil is important. And an oil purifier is one of key components in marine diesel engines. At present, the element type full-flow oil filter has been widely used for cleaning the engine oil. The self-driven centrifugal oil purifier is a device which is used to remove the impurities in lubrication oil using a jet flow. The flow characteristics and the physical behaviors of particles in this self-driven oil purifier were investigated numerically and the filtration efficiencies were evaluated. For calculations, a Computational Fluid Dynamics method is used and the Shear Stress Transport turbulence model has been adopted. The Multi Frames of Reference method is used to consider the rotating effect of the flows. The influence of centrifugal forcehas been numerically investigatedto improve filtration efficiency of tiny particles. As a result of this research, it was found that the particle filtration efficiency using the only center axis rotating and outer wall rotating system are higher than that of the fully rotating system in the self-driven oil purifier.