• Journal of Conservation Science
• /
• v.26 no.2
• /
• pp.133-142
• /
• 2010

This paper focused on desalination method for the underwater archaeological ceramics. The desalination method applied in this study takes additional conditions such as the amount of desalting water, temperature, and agitation conditions and compares the effects of desalt process. The result of efficiency rate appears that the twenty-times of the object weight of desalting water is more effective than that of ten-times one, but shows less economic compared to the cost. In addition, the research shows that the efficiency rate has been improved around 20 to 30 %, yet such improvement is not taken into account as an effective result considering the risk of damage from the physical and chemical impact and the consumption of energy in applying additional method.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.273-273
• /
• 2014

Quantum-dot sensitized solar cells (QDSCs) are an emerging class of solar cells owing to their easy fabrication, low cost and material diversity. Despite of the fact that the maximum conversion efficiency of QDSCs is still far less than that of Dye-Sensitized Solar Cells (>12 %), their unique characteristics like Multiple Exciton Generation (MEG), energy band tune-ability and tendency to incorporate multiple co-sensitizers concurrently has made QDs a suitable alternative to expensive dyes for solar cell application. Lead Sulfide (PbS) Quantum dot sensitized solar cells are theoretically proficient enough to have a photo-current density ($J_{sc}$) of $36mA/cm^2$, but practically there are very few reports on photocurrent enhancement in PbS QDSCs. Recently, $Hg^{2+}$ incorporated PbS quantumdots and Cadmium Sulfide (CdS) co-sensitized PbS solarcells are reported to show an improvement in photo-current density ($J_{sc}$). In this study, we explored the efficacy of $In_2S_3$ as an interfacial layer deposited through SILAR process for PbS QDSCs. $In_2S_3$ was chosen as the interfacial layer in order to avoid the usage of hazardous CdS or Mercury (Hg). Herein, the deposition of $In_2S_3$ interfacial layer on $TiO_2$ prior to PbS QDs exhibited a direct enhancement in the photo-current (Isc). Improved photo-absorption as well as interfacial recombination barrier caused by $In_2S_3$ deposition increased the photo-current density ($J_{sc}$) from $13mA/cm^2$ to $15.5mA/cm^2$ for single cycle of $In_2S_3$ deposition. Increase in the number of cycles of $In_2S_3$ deposition was found to deteriorate the photocurrent, however it increased $V_{oc}$ of the device which reached to an optimum value of 2.25% Photo-conversion Efficiency (PCE) for 2 cycles of $In_2S_3$ deposition. Effect of Heat Treatment, Normalized Current Stability, Open Circuit Voltage Decay and Dark IV Characteristics were further measured to reveal the characteristics of device.

• Macromolecular Research
• /
• v.17 no.2
• /
• pp.91-98
• /
• 2009

Conjugated PPV-derived block copolymers containing 2-ethylhexyloxynaphthalene unit were synthesized and characterized in this study. The resulting polymers were soluble in common organic solvents and showed good thermal stabilities, The weight-average molecular weights ($M_w$) of the copolymers ranged from 246,000 to 475,000 with PDIs of $1.3{\sim}2.1$. The optical properties of these polymers, measured both in a chloroform solution and on a film, showed a maximum absorption at $405{\sim}476\;nm$ for Copolymers $I{\sim}VIII$. In the PL spectra, Copolymers $I{\sim}VIII$ showed maximum peaks at $510{\sim}566\;nm$. The HOMOs, LUMOs and band gaps of the PPV derivatives of Copolymers $I{\sim}VIII$ were $5.30{\sim}5.77$, $3.04{\sim}3.24$, and $2.5{\sim}2.2\;eV$, respectively, The multi-layered, light-emitting diodes of ITO/PEDOT/copolymers/LiF/Al exhibited turn-on voltages of $6{\sim}2.5\;V$ Copolymer VIII exhibited the maximum brightness of $3.657\;cd/m^2$. Particularly, Copolymer VII, with an identical composition of MEH-PPV and naphthalene-PPV, showed a maximum luminance efficiency and power efficiency of 2,63 cd/A and 1.06 lm/W, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.7
• /
• pp.1553-1558
• /
• 2009

A series of Eu(III) complexes with various neutral ligands (2,2’:6’,2"-terpyridine (T), diglyme (D), 1N-(2-dimethylamino) ethyl)-1N, 2N, 2N-trimethylethane-1,2-diamine (PT), di-(2-picolyl)-amine derivative (HT), and multidentate terpyridine derivative (DT)) were synthesized to investigate the effect of coordination environment on the sensitized luminescence of Eu(III) complexes. The nine coordination sites of the $Eu^{3+}$ ion are occupied by three bidentate carboxylate moieties and one neutral ligand. The highest emission intensity is obtained for $Eu^{3+}$- $[NA]_3$ (PT), due to the difference in energy transfer efficiency and symmetry of the first coordination sphere of $Eu^{3+}$ ion. But, the lowest emission intensity is obtained for $Eu^{3+}$-$[NA]_3$(T). Terpyridine may not play an important role antenna for photosensitizing $Eu^{3+}$ ion. It could be attributed to the weak spectral overlap integral J value between its phosphorescence band and $Eu^{3+}$ion absorption band. Therefore, different coordination environment of $Ln^{3+}$ ion play an important role in providing sensitization of lanthanide ion emission.

• Journal of the Korea Convergence Society
• /
• v.13 no.3
• /
• pp.197-202
• /
• 2022

The CZTS solar cell is a thin film solar cell using an absorption layer composed of Cu, Zn, Sn, Se, and S, and is cheaper than a CIGS solar cell using In and Ga and more eco-friendly than a perovskite and CdTe solar cell using Pb and Cd. In this study, we conducted a bending test for flexible CZTS solar cells. Experiments were conducted in the direction of inner benidng with compressive stress and outer bending with tensile stress, and during the number of bending 1,000 times with a radius of curvature of 50 mmR, the efficiency of the solar cell decreased by up to 12.7%, and the biggest cause of efficiency reduction in both directions was a large decrease in parallel resistance.

• Korean Journal of Materials Research
• /
• v.20 no.11
• /
• pp.586-591
• /
• 2010

Solar cells have been more intensely studied as part of the effort to find alternatives to fossil fuels as power sources. The progression of the first two generations of solar cells has seen a sacrifice of higher efficiency for more economic use of materials. The use of a single junction makes both these types of cells lose power in two major ways: by the non-absorption of incident light of energy below the band gap; and by the dissipation by heat loss of light energy in excess of the band gap. Therefore, multi junction solar cells have been proposed as a solution to this problem. However, the $1^{st}$ and $2^{nd}$ generation solar cells have efficiency limits because a photon makes just one electron-hole pair. Fabrication of all-silicon tandem cells using an Si quantum dot superlattice structure (QD SLS) is one possible suggestion. In this study, an $SiO_x$ matrix system was investigated and analyzed for potential use as an all-silicon multi-junction solar cell. Si quantum dots with a super lattice structure (Si QD SLS) were prepared by alternating deposition of Si rich oxide (SRO; $SiO_x$ (x = 0.8, 1.12)) and $SiO_2$ layers using RF magnetron co-sputtering and subsequent annealing at temperatures between 800 and $1,100^{\circ}C$ under nitrogen ambient. Annealing temperatures and times affected the formation of Si QDs in the SRO film. Fourier transform infrared spectroscopy (FTIR) spectra and x-ray photoelectron spectroscopy (XPS) revealed that nanocrystalline Si QDs started to precipitate after annealing at $1,100^{\circ}C$ for one hour. Transmission electron microscopy (TEM) images clearly showed SRO/$SiO_2$ SLS and Si QDs formation in each 4, 6, and 8 nm SRO layer after annealing at $1,100^{\circ}C$ for two hours. The systematic investigation of precipitation behavior of Si QDs in $SiO_2$ matrices is presented.

• Polymer(Korea)
• /
• v.25 no.3
• /
• pp.399-405
• /
• 2001

Poly[3-octylthiophene-co-3-(4-fluorophenyl)thiophene]s were synthesized in 2:1, 1:1, and 1:2 mole ratios, and organic electroluminescent devices were fabricated using the copolymers. The opto-electrical properties of the copolymers were studied by PL, EL spectra, I-V, and V-L curves of the organic electroluminescent devices in conjunction with the energy band diagrams which were obtained from the cyclic voltammogram and the electronic absorption spectra. The LUMO energy level of P(OT/FPT)(1:1) is the lowest as -3.35 eV. In the copolymers P(OT/FPT)(2:1) and P(OT/FPT)(1:1) the ${\lambada}_{max}$ in the PL and EL spectra red-shifted as the mole ratio of fluorophenyl group increased while in P(OT/FPT)(1:2) it showed a blue-shift. This indicates that the backbone chain is twisted due to the steric hinderance of the fluorophenyl group leading to shorter ${\pi}$-conjugation length. P(OT/FPT)(1:1) showed the highest EL intensity and the highest power efficiency among the three copolymers. In P(OT/FPT)(1:2) the roughness of the film surface causes unusually high local leakage current leading to the low efficiency of electroluminescence.

• Analytical Science and Technology
• /
• v.9 no.3
• /
• pp.262-269
• /
• 1996

The muiltiwire proportional counter for the measurement of low-level and environmental $\alpha$ particles emitting nuclides was developed. External dimension of the devloped multiwire proportional counter is $350{\times}290{\times}30mm$ and the sensitivity area is $250{\times}200mm$. The wall material of the detector was selected the stainless steel to prevent the deformation by external impact and to obtain minimum background. The anode and cathode wires were used the stainless steel material of diameter $50{\mu}m$. The spacing of each wires are 10.0mm, 5.0mm and the numbers of total wire are 21, 42 lines, respectively. The multiwire proportional counter was designed that the measurement source is placed within the detector to prevent the wall absorption effect and the efficiency variation by various source heights. The characteristics of the developed detector have been investigated to obtain the plateau, operating voltage, background, counting efficiency, position sensitivity and energy resolution etc. For the $^{241}Am$ nuclide, the calculated LLD(Lower Limit of Detection) is 5.0mBq/L which is lower than 40mBq/L of recommended LLD value by ISO(International Organization for Standardization).

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.7
• /
• pp.449-455
• /
• 2016

Fog causes economic losses in transportation. It also results in health problems when it is combined with air pollutants. Considerable research efforts have focused on developing fog removal systems. However, most systems operate themselves after monitoring the fog. Additionally, continuous energy supply and maintenance are required to retain the fog-removal efficiency of the system. This study included the demonstration of a moss filter (a polyolefin mesh interlaced with moss) as a fog-removal method overcoming the limitations of the fog removal system. Three types of mosses with different surface structures were investigated to elucidate the relation between the moisture absorption rate and the structures. Among the different moss types, Hypopterygium japinicum showed the highest efficiency based on the smallest pore diameter and the largest total pore area. The visibilities with the moss filter and the polyolefin mesh were compared to perform the fog removal tests. The moss filter could provide a cost-effective and eco-friendly fog removal system with sustainability.

• Journal of the Korean Institute of Gas
• /
• v.27 no.2
• /
• pp.25-31
• /
• 2023

The purpose of this study is to increase the thermal efficiency of a landfill gas (LFG) power generation engine by capturing carbon dioxide (CO₂) from landfill gas (LFG) using monoethanolamine (MEA), which is widely used in the chemical CO₂ absorption process. Since the use of LFG as an energy source can be a means of reducing greenhouse gas emissions, MEA can be used to reduce CO₂ in LFG and increase the concentration of CH₄ to improve the efficiency of power generation. In this study, experiments were conducted to measure the solubility of CO₂ and CH₄ in MEA solution, increase the solubility under different conditions, and analyse the dissolution characteristics. It was found that the CO₂ absorption rate increased as the ratio of MEA to reaction gas increased. There is an optimum MEA concentration to maximise CO₂ solubility, and even if the concentration is increased above this concentration, the solubility does not improve significantly. This study provided fundamental work to develop a more practical fuel by capturing CO₂ from LFG and increasing the concentration of CH₄ while reducing greenhouse gas emissions.