• Journal of Biosystems Engineering
• /
• 제9권2호
• /
• pp.65-73
• /
• 1984

While most of researches on the performance of high temperature grain dryer have dealt mainly with improving dryer capacity and drying speed during the last twenty years, energy efficiency, in fact, has not been emphasized. Current fuel supplies and energy cost have shifted the emphasis to reducing the energy consumption for grain drying while maintaining dryer capacity and grain quality. Since the energy input for drying is relatively large, the recovery and reuse of at least part of the exhaust energy can significantly reduce the total energy consumption in existing drying systems. Unilization of exhaust heat in grain dryer either through direct recycling or by a thermal coupling in heat exchanger have been subject of a number of investigators. However, very seldom research in Korea has been done in this area. Three drying tests(non-recycling, 0.22 recycle ratio, and 0.76 recycle ratio)were performed to investigate the thermal efficiency and heat loss factors of continuous flow type dryer, and to analyze the effect of recycle ratio (weight of exhaust air recycled/total weight of input air) on the energy requriements for rough rice drying. The test results showed that when the exhaust air was not recycled, the energy lost from furnace was 15.3 percent of input fuel energy, and latent and sensible heat of exhaust air were 61.4 percent and 11.2 percent respectively. The heat which was required in raising grain temperature and stored in dryer was relatively small. As the recycle ratio of exhaust air was increased, the drying rate was suddenly decreased, and thermal efficiency of the kerosene burner was also decreased. Drying test with 0.76 recycle ratio resulted in 12.4% increase in fuel consumption, and 38.4% increase in electric power consumption as compared to the non-recycled drying test. Drying test of 0.22 recycle ratio resulted in 6.8% saving in total energy consumption, 8.0% reduction in fuel consumption, and 2.5% increase in electric power consumption as compared to the non-recycled drying test.

• 수산해양기술연구
• /
• 제50권1호
• /
• pp.67-74
• /
• 2014

Most of steam power plants in Korea are using the method of heating the feed water whenever the ambient temperature around the power plant area below $5^{\circ}C$ to prevent freezing water flowing in the pipe in winter time. But this kind of heat supplying system is not useful to save energy. If we take the method that the temperature of the each pipe is controled by direct measure of temperature by attaching sensor on the outside surface of the feed water tubes, then we can expect that a plenty of energy can be saved. In this study, the computer simulation is used to compare the energy consumption loads of both systems. Energy saving rate is calculated for the location of Incheon area in winter season. Four convection heat transfer coefficients for the ambient air and three initial flowing water temperature inside the tube were used. The result shows that the temperature control system using sensor represents more than 95% of energy saving rate in Incheon area. Even in the severe January weather condition, the energy saving rate is almost 75% in two days basis and even 83% in one day basis.

• Journal of Electrochemical Science and Technology
• /
• 제10권2호
• /
• pp.115-122
• /
• 2019

In order to improve the current efficiency and reduce the energy consumption in the electrosynthesis of ammonium persulfate, electrolytic properties of a perfluorosulfonic cation exchange membrane named PGN membrane and the $Al_2O_3$ ceramic membrane in the electrosynthesis of ammonium persulfate were studied and compared in a pilot electrolytic cell using a welded platinum titanium as the anode and a Pb-Sb alloy as the cathode. The effect of cell voltage, electrolyte flow rate and electrolysis time of the electrolytes on the current efficiency and the energy consumption were studied. The results indicated that the PGN membrane could improve current efficiency to 95.12% and reduce energy consumption to $1110kWh\;t^{-1}$ (energy consumption per ton of the ammonium persulfate generated) under the optimal operating conditions and the highest current efficiency of the $Al_2O_3$ ceramic membrane was 72.61% with its lowest energy consumption of $1779kWh\;t^{-1}$. Among 5 times of the electrolysis of the electrolytes, the lowest current efficiency of the PGN membrane was 85.25% with the highest energy consumption of $1244kWh\;t^{-1}$ while the lowest current efficiency of the $Al_2O_3$ ceramic membrane was 67.44% with the highest energy consumption of $1915kWh\;t^{-1}$, which suggested the PGN membrane could be used in the 5-stage electrolytic cell for the industrially continuous electrosynthesis of ammonium persulfate. Therefore the PGN membrane can be efficient to improve the current efficiency and reduce the energy consumption and can be applied in the industrial electrosynthesis of ammonium persulfate.

• The Korean Journal of Physiology
• /
• 제5권2호
• /
• pp.29-40
• /
• 1971

Oxygen consumption, pulmonary ventilation, heart rate, and breathing frequency were measured on 8 men walking on a treadmill carrying load of 9 kg on hand, back, or head. Besides measurements were made on subjects carrying loads of 2.6 kg each on both feet. The speed of level walking was 4, 5, and 5.5km/hr and a fixed speed off km/hr with grades of 0, 3, 6, and 9%. Comparisons were made between free walking without load and walking with various types of loads. The following results were obtained. 1. In level or uphill walking the changes in oxygen consumption, pulmonary ventilation, breathing frequency and heart rate were smallest in back load walking, and largest in hand load walking. The method of back load was most efficient and hand load was the least efficient. The energy cost in head load walking was smaller than that of in hand load walking. It was assumed that foot load costed more energy than hand load. 2. In level walking the measured parameters increased abruptly at the speed of 5.5 km/hr. Oxygen consumption in a free walking at 4 km/hr was 11.4ml/kg b.wt., and 13.1 ml/kg b.wt. 5.5 km/hr, and in a hand load walking at 4 km/hr was 13.9, and 18.8 ml/kg b. wt. at 5.5 km/hr. 3. In uphill walking oxygen consumption and other parameters increased abruptly at the grade of 6%. Oxygen consumption at 4 km/hr and 0% grade was 11.4 ml/kg b. wt., 13.6 at 6% grade, and 16.21/kg b. wt. at 9% grade in a free walking. In back load walking oxygen consumption at 4km/hr and 0% grade was 12.3 ml/kg b.wt.,14.9 at 6% grade, and 18.7 ml/kg b.wt. In hand load walking the oxygen consumption was the greatest, namely, 13.9 at 0% grade, 17.9 at 6%, and 20.0 ml/kg b. wt. at 9% grade. 4. Both in level and uphill walking the changes in pulmonary ventilation and heart rate paralleled with oxygen consumption. 5. The changes in heart rate and breathing frequency in hand load were characteristic. Both in level and uphill walk breathing frequency increased to 30 per minute when a load was held on hand and showed a small increase as the exercise became severe. In the other method of load carrying the Peak value of breathing frequency was less than 30 Per minute. Heart rate showed 106 beats/minute even at a speed of 4 km/hr when a load was held on hand, whereas, heart rate was between, 53 and 100 beats/minute in the other types of load carriage. 6. Number of strides per minute in level walking increased as the speed increased. At the speed floater than 5 km/hr number of strides per minute of load carrying walk was greater than that of free walking. In uphill walk number of strides per minute decreased as the grade increased. Number of strides in hand load walk was greatest and back load walk showed the same number of strides as the free walk.

• Nutrition Research and Practice
• /
• 제8권1호
• /
• pp.81-93
• /
• 2014

This study was conducted to investigate nutrient consumption by Korean adults in various places. To accomplish this, we used the 1998-2009 Korea National Health and Nutrition Examination Survey (KNHANES). Subjects of this investigation were over 19 years and the study included 37,160 people. The meals were categorized as breakfast, lunch, dinner, and snacks consumed at home, or while eating-out. Investigation of the rate of consumption at serving places based on daily meals and years showed that eating-out generally increased with time. The consumption of meals prepared at home was higher than that of meals consumed anyplace else in 1998, 2001, 2005, and 2007-2009. However, the rate of consumption of home meals decreased from 1998 to 2007-2009, while the rate of eating-out increased during this period. Annual nutrient intake according to serving places with respect to meals, energy, fat, and sodium were significantly lower in home meals than those consumed elsewhere in 2007-2009 relative to 1998. The sodium intake and energy distribution ratio of fat in meals consumed while eating-out increased significantly from 1998 to 2007-2009. The energy, fat and sodium intake and energy contribution ratio of fat consumed in meals at institutions was significantly higher in 2007-2009 than in 1998. Based on these results, additional research is required to develop guidelines for dietary life improvement at each serving place and to address education and policies for balanced nutrition intake.

• 태양에너지
• /
• 제18권3호
• /
• pp.41-50
• /
• 1998

일반적으로 최종적인 건물 설계에 의한 건물의 에너지 성능은 거주후평가(POE)에 의해 이루어지게 되며, 축적된 평가 결과는 설계에 의한 시행착오를 예측하기 위한 새로운 설계의 Feedback 자료로 이용되어져야 한다. 그러나 이러한 기존 건물의 에너지 평가자료가 구체적으로 편집되어 제시되어 있지 못한 현 실정에서 본 조사는 설계시에 에너지 성능을 비교할 수 있는 척도를 제공해 줄 수 있을 것이며, 추후 건물 에너지 성능규제를 위한 기초 자료가 될 수 있을 것이다. 이에 대전 및 인근지역 35개 공공건물의 건물에너지소비의 패턴이 조사되었으며, 우선 전화국, 백화점, 병원, 연구소, 스포츠센터 수영장, 전시관, 대학교, 호텔의 8개 건물로 분류하였다. 그러나 많은 수의 공공건물은 여러 가지 복합적인 기능을 갖추고 있고 따라서, 건물의 이름만으로 건물의 에너지소비패턴을 분석하기 위하여 (1) 준공연도, (2) 층수, (3) 단열정도, (4) 주연료, (5) 난방면적, (6) 연간난방일수, (7) 평균난방실내온도, (8) 냉방면적, (9) 평균냉방실내온도, (10) 보일러형식, (11) 보일러대수, (12) 보일러용량, (13) 보일러연료사용량, (14) 전기사용량, (15) 최대부하등이 조사되었다.

• 동력기계공학회지
• /
• 제19권3호
• /
• pp.29-35
• /
• 2015

Environmental pollution is produced by consumption of fossil fuel, therefore alternative fuels is interested for development of new energy resources and reduction of exhaust emissions for air pollution prevention. Biofuels are produced from new vegetable oil and animal fat, may be used as fuel without change of engine structure in diesel engine. In this paper, the test results on specific fuel consumption, combustion characteristics of neat diesel oil and biodiesel blends(10 vol.% biodiesel and 20 vol.% biodiesel) were presented using four stroke, direct injection diesel engine, especially this biodiesel was produced from biodiesel fuel at our laboratory by ourselves. This study showed that specific fuel consumption is increased slightly, on the other hand cylinder pressure, rate of pressure rise, rate of heat release and soot were decreased slightly in the case of biodiesel blends than neat diesel oil.

• Journal of Information Processing Systems
• /
• 제16권2호
• /
• pp.460-477
• /
• 2020

As one of the most significant challenges in the virtual data center, the virtual data center embedding has attracted extensive attention from researchers. The existing research works mainly focus on how to design algorithms to increase operating revenue. However, they ignore the energy consumption issue of the physical data center in virtual data center embedding. In this paper, we focus on studying the energy-aware virtual data center embedding problem. Specifically, we first propose an energy consumption model. It includes the energy consumption models of the virtual machine node and the virtual switch node, aiming to quantitatively measure the energy consumption in virtual data center embedding. Based on such a model, we propose two algorithms regarding virtual data center embedding: one is heuristic, and the other is based on particle swarm optimization. The second algorithm provides a better solution to virtual data center embedding by leveraging the evolution process of particle swarm optimization. Finally, experiment results show that our proposed algorithms can effectively save energy while guaranteeing the embedding success rate.

• Nuclear Engineering and Technology
• /
• 제54권4호
• /
• pp.1301-1311
• /
• 2022

Global climate change brings environmental quality sensitivity, especially in developed countries. Developed countries use non-renewable energy sources intensively both in their own countries and in other countries, they make productions that cause an enormous rate of increase in CO₂ emissions and unsustainable environmental costs. This has increased the interest in environmentally friendly alternative energy sources. The aim of this study is to investigate the impact of nuclear energy consumption and technological innovation on environmental quality in G7 countries using annual data over the period 1970-2015. The Panel Threshold Regression Model was used for the analysis. Empirical findings have indicated that the relationship between nuclear energy consumption and carbon emissions differs according to innovation for nuclear power plants. It was also concluded that nuclear energy consumption reduces carbon emissions more after a certain level of innovation. This result shows that the increase in innovative technologies for nuclear power plants not only increases energy efficiency but also contributes positively to environmental quality.

• Journal of Biosystems Engineering
• /
• 제8권2호
• /
• pp.49-61
• /
• 1983

U shape multitube heat exchanger was equipped in the flue to recover the exhaust heat from the boiler system. The fluids of the exhaust heat recovery equipment were the flue gas as the hot fluid, and the water as the cold fluid. The flow geometry of the fluids was cross flow - two pass, the hot fluid being mixed and the cold fluid unmixed. The results of the theoretical and the experimental analysis and the economic evaluation are summarized as follows. 1) The heat exchanger effectiveness and the temperature efficiency of the hot fluid were about 35% when the fuel consumption rate was 140 - 150 L/15min. The temperature efficiency for the cold fluid ranged from 3.0% to 4.5%. The insulation efficiency ranged from 85% to 98%, which was better than the KS air preheater insulation efficiency of 90%. 2) The relationship between the fuel consumption rate, F, and the outlet temperature, $T_{h2}$, of the flue gas from the heat exchanger was $T_{h2}$ = 0.927F + 110. In order to prevent the low temperature corrosion from the coagulation of $SO_3$, it is necessary to maintain the fuel consumption rate above 82 L/15min. 3) The ratio of the exhaust heat from the boiler system to the total energy consumption was about 14.5%. With the installation of the exhaust heat recovery equipment, the energy recovery ratio to the exhaust heat was about 25%. Accordingly, about 3.6% of the total fuel consumption was estimated to be saved. 4) Economic analysis indicated that the installation of the exhaust heat recovery equipment was feasible to save the energy, because the capital reocvery period was only 10 months when the fuel consumption rate was 80 L/15min. 4 months when it was 160 L/15min. 5) Based on the theoretical and the experimental analysis, it was estimated to save the energy of about 18 million Won per year, if four heat exchangers are installed in a factory. 6) A further study is recommended to identify the relationship among the flow rate of the exhaust gas, the size of the heat exchanger and the capacity of the air preheater. For a maximum heat recovery from the exhaust gas an automatic control system is required to control the flow rate of the cold fluid depending on the boiler load.