• Geosystem Engineering
• /
• v.21 no.6
• /
• pp.335-343
• /
• 2018

Alkali-surfactant polymer flooding has become an important technique to improve oil recovery following the development of oil fields while the function of emulsification in enhanced oil recovery is rarely considered in the existing mathematical model for numerical simulation. In this paper, the mechanism of improving the recovery of the emulsification was analyzed in ASP flooding, and a relatively perfect mathematical model with deep filtration-theory was established, in which oil-water volume equation, saturation equation, viscosity equation, and permeability reduction equation are included. The new model is used to simulate the actual block of an oil field; the simulated results of the new model and an old model without considering the emulsification are compared with the actual well history. It is found that new model which is easy to be realized in numerical simulation has a high precision fitting, and the effect of adding oil and decreasing water is obvious. The sensitivity of emulsification was analyzed, and the results show that the water reducing funnel becomes wider and the rate of water cut decreases rapidly with the increase of emulsifying capacity, and then the rate of recovery slows down. The effect of increasing oil and decreasing water is better, and the degree of recovery increases. The emulsification of the ASP flooding is maintained at a moderate level, which corresponds to ${\Phi}=0.2$ in the new model, and the emulsification is applied to realize the general mathematical quantitative description, so as to better guide the oilfield development.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.20 no.1
• /
• pp.64-81
• /
• 1994

O/W emulsions with mixed nonionic surfactants(polyoxyethylene(20)sorbitan monostearate/sorbitan sesquioleate), liquid paraffin, water prepared by direct inversion emulisification method and continuous inversion emulsification Method. The one-step, two-step and three-step phase inversion emulsification method were used in experiments. Effect of added water on droplet size of final O/W emulsions which is prepared by phase inversion emulsification method were investigated. In direct inversion emulsification method(two-step emulsification method), fine and homogeneous droplets of OIW emulsions were formed after phase inversion steps i.e. ,W/O - (W/O) If double emulsion - O/W emulsion. In continuous inversion emulsification method(three-step emulsification method), fine and homogeneous O/W emulsion were formed after phase inversion steps i.e., W/O - pseudomicroemulsion - O/W. By latter method, more Fine and homogenuous droplets were formed than former method. 10-10, 8 HLB region of mixed non-ionic surfactants could produce most fine droplets. This HLB region had maximum values of solubilization water and This HLB value of mixed nonionic surfactants produced fine and homogenuous droplets.

• Journal of Environmental Science International
• /
• v.18 no.11
• /
• pp.1261-1270
• /
• 2009

Fifty hydrocarbon-metabolizing microorganisms were isolated from soil samples polluted by the petroleum oils in Gamman-dong, Busan. Among them, strain 2-3A, showing strong emulsification activity, was selected by oil film-collapsing method. This bacterium was identified as Acinetobacter sp. and designated as Acinetobacter sp. 2-3A. The optimum temperature and pH on the growth of Acinetobacter sp. 2-3A were $25^{\circ}C$ and pH 7.0, respectively. The carbon and nitrogen sources for the most effective emulsification activity were 3.0% olive oil and 0.5% peptone, respectively. The 0.15% potassium phosphate was the most effective emulsification activity as a phosphate source. The optimum emulsification activity condition was $20^{\circ}C$, pH 7.0, and 2.0% NaCl. The optimum time for the best production of biosurfactant was 27 hrs. The emulsification stability was maintained at the temperature range from $4^{\circ}C$ to $100^{\circ}C$, pH range from 6.0 to 10.0, and NaCl range from 0% to 10%. For the oil resolvability of the biosurfactant, the residual oils were investigated by gas chromatography. As a result, it was verified that the biosurfactant decreased and decomposed crude oils from $_nC_{10}$ to $_nC_{32}$.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.38 no.4
• /
• pp.263-270
• /
• 2012

Ascorbic acid (Vitamin C) becomes unstable in the aqueous phase by oxygen, light and alkali, etc. The properties are limited in application to cosmetics. The most important factor that determines the destabilization of ascorbic acid in the aqueous phase was tried to understand considering its molecular deformation and degradation. In this study, we changed the polyols and emulsification technique for the stability of ascorbic acid. Then we observed the color and concentration change of ascorbic acid at room temperature and high temperature ($42^{\circ}C$) for 6 weeks and identified the stability using HPLC regularly. As a result, we found that glycerin was the most appropriate polyol for stability of the ascorbic acid. Also the technique of nonaqueous emulsification stabilized ascorbic acid than P/S emulsification. Also, P/S emulsification, glycerin was more stable than propylene glycol. By the results we suggest that ascorbic acid could be stabilized by nonaqueous emulsification method and this data could be applied to stabilization methods for cosmetic products.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.4
• /
• pp.77-84
• /
• 2012

The lithographic process depends on a satisfactory ink-in-water emulsion being formed during printing and the speed of wet presses makes the choice of fountain solution vitally important as the ink and fount must react quickly to form a stable emulsion. Ink and water come into contact with each other on the rolls of the press and are forced together in the roll nips. The water is not soluble in the ink since it is slightly fat. Instead, an emulsion is formed, a heterogeneous mass consisting of small water drops mixed into the ink, if the water feed is too great. This emulsification can affect the properties of an off-set ink and negatively affect the printability. So we investigated the effects of the emulsification of phenol free heat-set ink and existing heat-set ink on printed quality, such as amount of ink transfer, printed density, print-through and uniformity. We used Duke emulsification tester for the emulsification of inks, and used IGT printability tester for printed quality. The printed quality were measured by densitometer and were evaluated by the image analysis system. Compared to conventional printing ink, phenol-free ink showed better results of the printability at the emulsification.

• Proceedings of the Korean Printing Society Conference
• /
• 2001.06a
• /
• pp.135-140
• /
• 2001

Laboratory test method which determines the emulsification rate of dampening solution and ink has been described In lithography using the mutual repellence of oil and water, the emulsification is produced by dispersion of dampening water and ink because of the printing pressure on a practical press. Rheological properties of Ink-Water balance are the important factors in lithographic printing. The emulsification theory and laboratory test method deduced from Surland and Kim. It is shown that the emulfisication curves relate to the rates of change in the emulsifide ink\`s flow properties, to the shear stability of the emulsion formed To study on the factors determining the emulsion velocity, we have measured water pickup and calculated emulsification velocity constant \`k\` and activation energy.

• Membrane Journal
• /
• v.31 no.1
• /
• pp.52-60
• /
• 2021

When preparing calcium alginate microspheres using rotating membrane emulsification that rotates SPG (Shirasu porous glass) tubular membrane in the continuous phase, the optimal conditions of rotating membrane emulsification process parameters for producing monodisperse microspheres were determined. We determined the effects of process parameters of rotating membrane emulsification (the rotating speed of membrane module, the transmembrane pressure, the ratio of dispersed phase to continuous phase, the alginate concentration, the emulsifier concentration, the stabilizer concentration, the crosslinking agent concentration, and the membrane pore size) on the mean size and size distribution of alginate microspheres. As a result, the size of the microspheres decreased as the rotating speed of membrane module, the emulsifier concentration, and the crosslinking agent concentration increased among the process parameters of rotating membrane emulsification. On the contrary, as the ratio of dispersed phase to continuous phase, the transmembrane pressure, and the alginate concentration increased, the size of the microspheres increased. In the rotating membrane emulsification using an SPG membrane with a pore size of 3.2 ㎛, it was possible to finally prepare monodisperse alginate microspheres with a particle size of 4.5 ㎛ through the control of process parameters.

• Journal of Environmental Science International
• /
• v.6 no.5
• /
• pp.473-480
• /
• 1997

Microorganisms producing bioemulslfiler were isolated from the sea water In Pusan coastal area. The isolated strain which had the highest emulsification activity and stability was identified as the genus Achetobacter from the results of morphological. cultural and biochemical tests and named Achetobacter sp. EL-C6 for convenience. The compositions of optimum medium for emulsification of crude oil by Acinetobacter sp. EL-C6 were crude oil 2.0%, NH4NO3 0.2%, $K_2HPO_4$ 0.01%, $MgSO_4$.$7H_2O$ 1.o%, $CaCl_2$.$2H_2O$ 0.1% and NaCl 3.0% at initial pH 7.5 and 3$0^{\circ}C$, respectively. The cultivation for emulsification of crude ell was carried out in 500m1 shaking flask containing 100m1 of the optimum medium at 3$0^{\circ}C$. The highest emulsification was observed after 5 days. The utilization on the various hydrocarbon of the Achetobacter sp. EL-C6 showed that utilization of n-alkane compounds were better than that of aromatic compounds. Among the petroleum compounds, crude ell was best utilized by the Achetobacter sp. EL-C6.

• Journal of the Korean Applied Science and Technology
• /
• v.15 no.2
• /
• pp.25-32
• /
• 1998

The emulsion stability of W/O emulsion prepared by D phase emulsification during storage and handling is studied by using phase diagrams. The process of D phase emulsification begins with the formation of isotropic surfactant solution, followed by formation of oil-in-surfactant (O/D) gel emulsion by dispersion of octamethylcyclotetrasiloxane(OMCS) in the surfactant solution. Polyols were essential components for this purpose. To understand the function of polyols, the solution behavior of nonionic surfactant/oil/water/polyol systems were investigated by the ternary phase diagrams of polyoxyethylene oleyl ether/OMCS/propylene glycol(PG) aqueous solutions. The addition of PG increased the solubility of oil in the isotropic surfactant phase. D phase emulsification method has been applied to a new type of cosmetics. By using this emulsification technique, O/W emulsion were formed without a need for adjust of HLB. Fine and stable W/O emulsions were prepared by D phase emulsion.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.20 no.1
• /
• pp.123-132
• /
• 2002

The literature often mentions the hardness of water in dampening solutions as possible source of problem. In most literature describes that the water hardness affects print quality. However water hardness affects not only print quality, but also emulsification of ink and dampening solution. Therefore the purpose of this study was to determine if water hardness actually affects the emulsification rate of dampening solution and ink. And this study for the factors determining the emulsion velocity, we have measured water pick-up and calculated emulsion velocity constant 'k' and activation energy.