• Journal of the Korean Geotechnical Society
• /
• v.20 no.9
• /
• pp.145-153
• /
• 2004

Based on the previous studies proposed by many researchers about the evaluation method of replacement depth, a modified formula which incorporates the effect factors such as embanked height and load, replacement depth, cohesive force of original ground and unit weight of embankment etc, was suggested in this study. The new proposed formula was applied in the three construction sites of Kwangyang-Bay Area (Yeocheon, Youlchon, and Kwangyang) constructed by the compulsion replacement method. The application of the new method was investigated through these case studies in domestics. A modified bearing capacity parameter was estimated form the relationship of modified embankment loading and ultimate bearing capacity resulted from the site investigation, and the replacement depth was predicted by using this parameter. In addition, through the relationship analyses between each effect factors to the replacement depth in two areas, Yeocheon and Youlchon, an empirical prediction method which can evaluate the replacement depth in adjoining area was proposed. The predicted value obtained by new method is approximately similar to the measured replacement depth in Kwangyang area.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.2
• /
• pp.166-174
• /
• 2009

The liquid column trajectory and column breakup length characteristics have been experimentally studied in angled jets injected into subsonic crossflow. Pulsed shadowgraph photography and Planar Liquid Laser Induced Fluorescence measurements were used to determine the angled effects. And the main objectives of this research are to get a empirical formula of liquid column trajectory and breakup length with below the $90^{\circ}$ degree injection angle conditions, and were compared with previous results. It was also found that the empirical formula, which reversed injection conditions of air stream. As the result, This has been shown that liquid column trajectories and column breakup length were spatially dependent on various injection angle, normalized injector exit diameter, air-stream and fuel injection velocity. Furthermore, the empirical formula of liquid column trajectories and breakup length has been some different of drag coefficient results between normal angled injection and reversed injection in subsonic crossflow.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.2
• /
• pp.71-76
• /
• 2017

The roll damping problem in the design of ships and offshore structures remains a challenge to many researchers due to the fluid viscosity and nonlinearity of the phenomenon itself. In this paper, the study on viscous roll damping of a circular cylinder was carried out using forced oscillations. The roll moment generated by forced oscillation using a torque sensor was measured for each forced oscillation period and compared with the empirical formula. Although the magnitude of the measured torque from the shear force was relatively small, the results were qualitatively similar to those obtained from the empirical formula, and showed good agreement with the quantitative results in some oscillation periods. In addition, the flow around the circular cylinder wall was observed closely through the PIV measurements. Owing to the fluid viscosity, a boundary layer was formed near the wall of the circular cylinder, and a minute wave was generated by periodical forced oscillations at the free surface through the PIV measurement. In this study, the suitability of the empirical formula for the roll moment caused by viscous roll damping was verified by model tests. The wave making phenomenon due to the fluid viscosity around the wall of a circular cylinder was testified by PIV measurements.

• Journal of the Korean Geosynthetics Society
• /
• v.19 no.4
• /
• pp.33-40
• /
• 2020

It is now common to find the wastes buried in the past during the excavation process of soil for large scale housing and land development. Without proper treatment of the wastes environmentally, the excavation process is no longer able to proceed, and an action plan should be provided to treat the wastes with environmental and economic viability. In the study, the relationship between the apparent density of the wastes and the volume conversion factor, which is the basis in the estimation of waste treatment cost was investigated. From 10 sampling points of a landfill site, wastes were sampled, analyzed for physical characteristics, and the apparent density of mixed and sorted waste was assessed. Applying the empirical formula, and the formula we suggested here, the volume conversion factors were compared with that measured directly in the field using dump truck and excavator. Obviously there was a close relationship among the volume conversion factors resulting from the empirical formula, the formula we suggested and that measured in the field.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.15 no.3
• /
• pp.186-189
• /
• 2003

Various empirical formulas have been developed to describe the stability of breakwater armor stones. The Hudson formula is known to have needs to be refined in many ways. but it is most widely used because of its simplicity. The van der Meer formula is sometimes used for the cross-check, but it is not very popularly used due to its complexity and the uncertainty of the relevant parameters. Recently, on the other hand, Yoo(2003) proposed a formula of a simple form using a new non-dimensional number which is called 'action slope' (abbreviated as Yoo formula hereinafter). In this study, in order to provide coastal engineers with some idea of the use of these formulas, their accuracies were estimated by comparing with the experimental data reported by van der Meer in 1987 and 1988. It was found that the van der Meer formula showed the highest accuracy, while the Hudson formula of very low accuracy needed considered judgment on its use. On the other hand, the Yoo formula of slightly lower accuracy but simpler expression than the van der Meer formula seems to be able to be used in engineering practice if a slightly higher safety factor is taken.

• Land and Housing Review
• /
• v.11 no.2
• /
• pp.75-86
• /
• 2020

As the urban regeneration project and the old housing maintenance project are actively progressing in Korea, small-scale building construction is being carried out in downtown areas. Small buildings in the downtown area are constructed on about 4 to 10 floors, and since they are carried out in small units in residential areas, it is difficult to enter large equipment to construct existing piles, and it is more vulnerable to complaints about noise and vibration. in this study, helical piles suitable for urban areas or small sites where it is difficult to enter large equipment, such as noise and vibration. Reliability analysis was performed on the results of the static load tests and dynamic load tests conducted at the LH site and the bearing capacity calculated by the hydrostatic method and the empirical formula (N value). As a result of comparing and analyzing the design formula and the results of static load test and dynamic load tests, the correlation between the design formula of the bored pile (Road bridge design standard) formula using N value and the design formula by the modified Davisson method frequently used by method commonly European helical file practitioners.

• Wind and Structures
• /
• v.16 no.6
• /
• pp.603-616
• /
• 2013

This study is aimed at formulating an empirical equation for the across-wind fluctuating moment and spectral density coefficient, which are needed to estimate the across-wind dynamic responses of tall buildings, as a function of the side ratios of buildings. In order to estimate an empirical formula, wind tunnel tests were conducted on aero-elastic models of the rectangular prisms with various aspect and side ratios in turbulent boundary layer flows. In this paper, criteria for the across-wind fluctuating moment and spectral density are briefly discussed and the results are analyzed mainly as a function of the side ratios of the buildings. Finally, empirical formulas for the across-wind fluctuating moment coefficient and spectral density coefficient according to variation of the aspect ratio are proposed.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.5
• /
• pp.504-508
• /
• 2007

In the case of thin plate blocks, buckling deformation due to longitudinal shrinkage is the most important weld-induced deformation. This paper is concerned with developing the formula to predict the longitudinal shrinkage due to welding, in which mechanical tension effect in welding direction is accounted for. For this purpose, bead on plate welding test has been carried out for the 27 thin plate specimens with varying welding conditions and magnitude of tensile load. Empirical formula of predicting the longitudinal shrinkage has been derived based on the results of welding test, in which effect of mechanical tension is included. The derived formula can be usefully used in predicting the level of tensile load to reduce the longitudinal shrinkage.

• Journal of the Korean Ceramic Society
• /
• v.54 no.3
• /
• pp.235-242
• /
• 2017

Changes in polarization and thermal expansion coefficients during temperature increase of a poled lead zirconate titanate (PZT) cube specimen switched by an electric field at room temperature are measured. The measured data are analyzed to construct governing differential equations for polarization and strain changes. By solving the differential equations, an experimental formula for the high temperature behavior of ferroelectric materials is obtained. It is found that the predictions by the formula are in good agreement with measures. From the viewpoint of macroscopic remnant state variables, it appears that the processes of electric field-induced switching at different temperatures are identical and independent of temperature between $20^{\circ}C$ and $110^{\circ}C$.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.5
• /
• pp.425-431
• /
• 2013

Estimation equations of shear modulus in the plane of laminated veneer lumber (LVL) were compared each other through uniaxial tension test results. The equations - basic elastic equation in the dimensional orthotropic case, Hankinson's formula and empirical equation proposed by Salikis and Falk, were applied to determine the elastic constants at various angles to the grain, which were needed for determination of shear modulus. Tensile elastic modulus of LVL predicted from these equations were compared with test data to evaluate the accuracy of the equation. Tensile elastic modulus rapidly decreased at orientations between 0 and 15 degrees and elastic modulus at grain angles of 15, 30, and 45 degrees overestimated in the presented equations. But the proposed equation by Salikis and Falk showed better prediction, especially at 30, and 45 degrees. This proposed formula would be more useful and practical for estimating of shear modulus of wood composites like LVL to minimize the effect of Poisson's ratio term.