• 교육녹색환경연구
• /
• 제10권2호
• /
• pp.1-7
• /
• 2011

An experimental study to evaluate structural capacity of an embedded plate connected with prestressed concrete beam was performed. Embedded steel plates and prestressed concrete beam were connected with stud-bolts at the ends of concrete beam specimens. About 1,000 kN concentrated load was applied at 450mm away from the end of beam specimen. A 3,000 kN capacity static Oil-jack was used to direct concentrated load. The maximum strain of stud-bolt recorded $90{\times}10^{-6}$(mm/mm) and wide width cracks were not founded. Any falling failures of concrete and large deformations were not founded either between steel plate and prestressed concrete specimen. As a result, construction performance can be improved using this embedded steel plate connection system apply to large space educational facilities.

• 국제초고층학회논문집
• /
• 제9권2호
• /
• pp.155-166
• /
• 2020

To connect exterior reinforced concrete (RC) columns with the steel belt truss, the gusset plates are welded to the steel plates embedded in the RC column. Then, the concrete around an embedded plate is very likely to be damaged by the heat input from a long-time (6 to 48 hours) welding of the embedded and gusset plates at a joint between RC columns and steel belt truss. However, very few studies have assessed the concrete damage caused by the welding heat between embedded and gusset plates, and no clear onsite solution has been found. In this paper, experimental tests have been carried out on 4 full-scale specimen to analyze the effect of long-time (about 6 hours) onsite welding (1-side welding and 3-side welding) between a gusset plate and an embedded plate in high strength concrete with compressive strength of 55 MPa and 80 MPa on RC columns. The effect of the long-time welding heat of embedded and gusset plates, which are used in real high-rise building construction sites, on concrete is analyzed in terms of the following three items: 1) temperature distribution, 2) pattern and characteristics of cracks, and 3) effect of the cracks on the compressive strength of RC column. Based on the experimental results, even though the heat input up to about 150? from the long-time onsite welding on the high-strength concrete column for the joint could result in concrete cracks in a radial form, it is found that the welding cracks have no effect on the axial stiffness and strength of the concrete column.

• 한국강구조학회 논문집
• /
• 제11권3호통권40호
• /
• pp.259-270
• /
• 1999

본 연구에서는 대수심 해안에서 호안 구조물의 조성에 적합한 근입식 강판셀 구조의 표준설계절차를 확립하고 최적제원 결정을 위한 연구를 수행하였다. 최적 제원의 결정을 위해 셀 안전성 검토용 전산프로그램을 개발하고 강도가 다른 사질토 지반에 대해 수심별로 가능한 제원을 프로그램을 사용하여 도출한 뒤 최적 강판셀 제원 결정을 위한 일반식을 제안하였다. 아울러 강판셀의 관입을 위한 진동햄머 시스템의 소요 기진력 산정식의 타당성을 확인하는 모형실험을 수행하였으며, 제안한 셀제원에 대한 소요 기진력의 데이터를 제시하였다.

• 한국방재학회 논문집
• /
• 제10권5호
• /
• pp.27-33
• /
• 2010

본 연구에서는 2,000 kN 용량의 actuator를 이용, 12 m 경간의 실물 크기로 제작된 프리스트레스트 콘크리트 보의 구조성능 평가를 위한 실험을 수행하였다. 보의 양 단에는 접합을 위한 강판을 매립하였으며 시험체는 별도로 제작된 철골 보에 고력볼트접합 방식으로 세팅되었다. 프리스트레스트 콘크리트와 슬래브 콘크리트의 설계기준강도는 각각 50 MPa와 24 MPa이며, 인장 철근으로 사용된 2-HD25 철근은 매립강판의 구성요소 중 하나인 수직강판에 용접하였다. 실험은 변위제어법에 의하여 수행되었으며 10 mm의 변위를 증가시키며 loading과 unloading을 반복적으로 가력하였다. 실험결과를 살펴보면, 탄성거동구간에서는 약 88.34%, 비탄성거동구간에서는 약 86.97% 그리고 소성거동구간에서는 약 66.83%의 프리스트레싱에 의한 변위복원능력을 나타냄을 알 수 있었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.301-304
• /
• 2008

본 연구에서는 싱글 플레이트 전단접합에 앵글을 접합한 새로운 방식의 철골 커플링보를 개발하여 여러 가지 구조적 성능을 평가하고자 한다. 주요 변수는 앵글유무, 콘크리트 보강 유무, 매립길이, 결손단면이다. 실험은 커플링 보의 가운데 지점을 2,000kN Actuator를 이용하여 횡방향 반복가력을 가하여 구조물의 전체적인 거동을 알아본다. 실험결과 싱글 플레이트 전단 접합부로 이루어진 실험체보다 앵글을 접합한 실험체가 강도, 변형능력, 강성, 에너지 소산 능력 등 전반적인 구조적 성능이 훨씬 우수한 것으로 나타났다. 매립된 철골보 주위에 전단철근을 보강하지 않은 경우 PC벽체의 조기 지압파괴로 인해 그 성능이 현저히 떨어지는 것으로 나타났다. 그러나 전단철근이 배근이 된 경우 철골 커플링 보의 전단 항복이 발생할 때까지 PC벽체의 파괴가 충분히 지연되는 것으로 나타났다. 앵글이 접합된 경우 매립길이가 작아도 그 성능이 떨어지지 않았다. 결손 단면이 있을 경우 강도는 작게 나타났으나 접합부 전단 강도보다 훨씬 작도록 설계된 관계로 PC벽체의 파괴가 발생하기 전에 충분히 전단 거동을 통해 우수한 성능을 발휘하였다. 이러한 결과는 시공성과 경제성 향상을 위해 앵글을 접합한 철골 커플링 보 방식이 매우 유용할 것으로 사료된다.

• Steel and Composite Structures
• /
• 제20권6호
• /
• pp.1275-1303
• /
• 2016

Steel plates and carbon-fiber-reinforced polymer (CFRP) laminates or plates bonded to concrete substrates have been widely used for concrete strengthening. However, this technique cause plate debonding, which makes the strengthening system inefficient. The main objective of this study is to enhance the bond strength of externally bonded steel plates and CFRP laminates to the concrete surface by proposing new embedded adhesive and steel connectors. The effects of these new embedded connectors were investigated through the tests on 36 prism specimens. Parameters such as interfacial shear stress, fracture energy and the maximum strains in plates were also determined in this study and compared with the maximum value of debonding stresses using a relevant failure criterion by means of pullout test. The study indicates that the interfacial bond strength between the externally bonded plates and concrete can be increased remarkably by using these connectors. The investigation verifies that steel connectors increase the shear bond strength by 48% compared to 38% for the adhesive connectors. Thus, steel connectors are more effective than adhesive connectors in increasing shear bond strength. Results also show that the use of double connectors significantly increases interfacial shear stress and decrease debonding failure. Finally, a new proposed formula is modified to predict the maximum bond strength of steel plates and CFRP laminates adhesively glued to concrete in the presence of the embedded connectors.

• Steel and Composite Structures
• /
• 제49권4호
• /
• pp.381-392
• /
• 2023

This study experimentally investigates the flexural behavior of steel-UHPC composite slabs composed of an innovative negative Poisson's ratio (NPR) steel plate and Ultra High Performance Concrete (UHPC) slab connected via demountable high-strength bolt shear connectors. Eight demountable composite slab specimens were fabricated and tested under traditional four-point bending method. The effects of loading histories (positive and negative bending moment), types of steel plate (NPR steel plate and Q355 steel plate) and spacings of high-strength bolts (150 mm, 200 mm and 250 mm) on the flexural behavior of demountable composite slab, including failure mode, load-deflection curve, interface relative slip, crack width and sectional strain distribution, were evaluated. The results revealed that under positive bending moment, the failure mode of composite slabs employing NPR steel plate was distinct from that with Q355 steel plate, which exhibited that part of high-strength bolts was cut off, part of pre-embedded padded extension nuts was pulled out, and UHPC collapsed due to instantaneous instability and etc. Besides, under the same spacing of high-strength bolts, NPR steel plate availably delayed and restrained the relative slip between steel plate and UHPC plate, thus significantly enhanced the cooperative deformation capacity, flexural stiffness and load capacity for composite slabs further. While under negative bending moment, NPR steel plate effectively improved the flexural capacity and deformation characteristics of composite slabs, but it has no obvious effect on the initial flexural stiffness of composite slabs. Meanwhile, the excellent crack-width control ability for UHPC endowed composite members with better durability. Furthermore, according to the sectional strain distribution analysis, due to the negative Poisson's ratio effect and high yield strength of NPR steel plate, the tensile strain between NPR steel plate and UHPC layer held strain compatibility during the whole loading process, and the magnitude of upward movement for sectional plastic neutral axis could be ignored with the increase of positive bending moment.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.422-429
• /
• 2005

It is limited to decrease height or section even by system conversion to indeterminate structure - continuous beam - in existing PSC girder bridges. In this study, the movement of connection is analyzed through actual field test, by increasing stiffness of negative moment area in continuous PSC bridge and developing continuous PSC bridge with embedded steel plate, that can overcome the demerit of existing connection. As a result, it is confirmed that the body unification of the connection is being realized and maintained. Moreover, the height of a span is suggested in continuous PSC girder bridge with embedded steel plate by computational analysis

• 대한임베디드공학회논문지
• /
• 제17권3호
• /
• pp.129-138
• /
• 2022

Collecting and labeling sufficient training data, which is essential to deep learning-based visual inspection, is difficult for manufacturers to perform because it is very expensive. This paper presents a steel plate surface defect detection system with industrial-grade detection performance by training a small amount of steel plate surface images consisting of labeled and non-labeled data. To overcome the problem of lack of training data, we propose two data augmentation techniques: program-based augmentation, which generates defect images in a geometric way, and generative model-based augmentation, which learns the distribution of labeled data. We also propose a 4-step semi-supervised learning using pseudo labels and consistency training with fixed-size augmentation in order to utilize unlabeled data for training. The proposed technique obtained about 99% defect detection performance for four defect types by using 100 real images including labeled and unlabeled data.

• Steel and Composite Structures
• /
• 제23권3호
• /
• pp.303-315
• /
• 2017

This paper describes the finite element model for predicting the fundamental performance of embedded steel column base connections under monotonic and cyclic loading. Geometric and material nonlinearities were included in the proposed finite element model. Bauschinger and pinching effects were considered in the simulation of embedded column base connections under cyclic loading. The degradation of steel yield strength and accumulation of plastic damage can be well simulated. The accuracy of the finite element model is examined by comparing the predicted results with independent experimental dataset. It is demonstrated that the finite element model accurately predicts the behaviour and failure models of the embedded steel column base connections. The finite element model is extended to carry out evaluations and parametric studies. The investigated parameters include column embedded length, concrete strength, axial load and base plate thickness. Moreover, analytical models for predicting the initial stiffness and bending moment strength of the embedded column base connection were developed. The comparison between results from analytical models and those from experiments and finite element analysis proved the developed analytical model was accurate and conservative for design purposes.