국제초고층학회논문집 (International Journal of High-Rise Buildings)

  • 제9권2호
  • /
  • Pages.155-166
  • /
  • 2020
  • /
  • 2234-7224(pISSN)
  • /
  • 2288-9930(eISSN)
한국초고층도시건축학회 (Council on Tall Building and Urban Habitat Korea)
권호 표지
DOI QR코드

DOI QR Code

Experimental Test on the Effect of Onsite Welding of Steel Plates for a Joint Between Concrete Columns and a Steel Belt Truss

  • Shim, Hak Bo (Research & Development Institute, Lotte Engineering & Construction) ;
  • Yun, Da Yo (Department of Architectural Engineering, Yonsei University) ;
  • Park, Hyo Seon (Department of Architectural Engineering, Yonsei University)
  • 발행 : 2020.06.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

To connect exterior reinforced concrete (RC) columns with the steel belt truss, the gusset plates are welded to the steel plates embedded in the RC column. Then, the concrete around an embedded plate is very likely to be damaged by the heat input from a long-time (6 to 48 hours) welding of the embedded and gusset plates at a joint between RC columns and steel belt truss. However, very few studies have assessed the concrete damage caused by the welding heat between embedded and gusset plates, and no clear onsite solution has been found. In this paper, experimental tests have been carried out on 4 full-scale specimen to analyze the effect of long-time (about 6 hours) onsite welding (1-side welding and 3-side welding) between a gusset plate and an embedded plate in high strength concrete with compressive strength of 55 MPa and 80 MPa on RC columns. The effect of the long-time welding heat of embedded and gusset plates, which are used in real high-rise building construction sites, on concrete is analyzed in terms of the following three items: 1) temperature distribution, 2) pattern and characteristics of cracks, and 3) effect of the cracks on the compressive strength of RC column. Based on the experimental results, even though the heat input up to about 150? from the long-time onsite welding on the high-strength concrete column for the joint could result in concrete cracks in a radial form, it is found that the welding cracks have no effect on the axial stiffness and strength of the concrete column.

키워드

참고문헌

  1. Taranath, B.S. (2010). "Reinforced concrete design of tall buildings." CRC Press. Boca Raton. FL.
  2. Park, H.S., Lee, E., Choi, S.W., Oh, B.K., Cho, T., Kim, Y. (2016). "Genetic-algorithm-based minimum weight designof an outrigger system for high-rise buildings." Eng. Struct., 117(5), 496-505. https://doi.org/10.1016/j.engstruct.2016.02.027
  3. Zong, L., Shi, G., Wang, Y. (2015). "Experimental investigation and numerical simulation on fatigue crack behavior of bridge steel WNQ570 base metal and butt weld." Constr. Build. Mater., 77(15), 419-429. https://doi.org/10.1016/j.conbuildmat.2014.12.063
  4. Pan, J., Chen, S., Lai, Z., Wang, Z., Wang, J., Xie, H. (2017). "Analysis and fracture behavior of welded box beam-to-column connections considering residual stresses." Constr. Build. Mater., 154(15), 557-566. https://doi.org/10.1016/j.conbuildmat.2017.07.228
  5. Mollicone, P., Camilleri, D., Gray, T.G.F., Comlekci, T. (2006). "Simple thermo-elastic-plastic models for welding distortion simulation." J. Mater. Process. Technol., 176(1-3), 77-86. https://doi.org/10.1016/j.jmatprotec.2006.02.022
  6. Deng, D., Murakawa, H. (2008). "Prediction of welding distortion and residual stress in a thin plate butt-welded joint." Comput. Mater. Sci., 43(2), 353-365. https://doi.org/10.1016/j.commatsci.2007.12.006
  7. Long, H., Gery, D., Carlier, A., Maropoulos, P.G. (2009). "Prediction of welding distortion in butt joint of thin plates." Mater. Des., 30(10), 4126-4135. https://doi.org/10.1016/j.matdes.2009.05.004
  8. Manurung, Y.H.P., Lidam, R.N., Rahim, M.R., Zakaria, M.Y., Redza, M.R., Sulaiman, M.S., Tham, G., Abas, S.K. (2013). "Welding distortion analysis of multipass joint combination with different sequences using 3D FEM and experiment." Int. J. Press. Ves. Pip., 111-112, 89-98. https://doi.org/10.1016/j.ijpvp.2013.05.002
  9. Li, Y., Wang, K., Jin, Y., Xu, M., Lu, H. (2015). "Prediction of welding deformation in stiffened structure by introducing thermo-mechanical interface element" J. Mater. Process. Technol., 216, 440-446. https://doi.org/10.1016/j.jmatprotec.2014.10.012
  10. Pham, T., Kim, S. (2017). "Characteristics of microstructural phases relevant to the mechanical properties in structural steel weld zone studied by using indentation." Constr. Build. Mater., 155(30), 176-186. https://doi.org/10.1016/j.conbuildmat.2017.08.033
  11. Mackwood, A.P., Crafer, R.C. (2005). "Thermal modelling of laser welding and related processes: a literature review." Opt. Laser Technol., 37(2), 99-115. https://doi.org/10.1016/j.optlastec.2004.02.017
  12. Winczek, J. (2011). "New approach to modeling of temperature field in surfaced steel element." Int. J. Heat Mass Transf., 54(21-22), 4702-4709. https://doi.org/10.1016/j.ijheatmasstransfer.2011.06.007
  13. Shen, J., Chen, Z. (2014). "Welding simulation of fillet-welded joint using shell elements with section integration, J. Mater. Process. Technol." 214(11), 2529-2536. https://doi.org/10.1016/j.jmatprotec.2014.04.034
  14. Alves do Carmo, D., Rocha de Faria, A. (2015). "A 2D finite element with through the thickness parabolic temperature distribution for heat transfer simulations including welding." Finite Elem. Anal. Des., 93, 85-95. https://doi.org/10.1016/j.finel.2014.09.005
  15. Jiang, C., Yang, Y., Wang, Y., Zhou, Y., Ma, C. (2014). "Autogenous shrinkage of high performance concrete containing mineral admixtures under different curing temperatures." Constr. Build. Mater., 61, 260-269. https://doi.org/10.1016/j.conbuildmat.2014.03.023
  16. Hajjar, J.F., Schiller, P.H., Molodan, A., (1998). "A distributed plasticity model for concrete-filled steel tube beam-columns with interlayer slip." Eng. Struct., 20(8), 663-676. https://doi.org/10.1016/S0141-0296(97)00107-7
  17. Aly, T., Elchalakani, M., Thayalan, P., Patnaikuni, I. (2010). "Incremental collapse threshold for pushout resistance of circular concrete filled steel tubular columns." J. Constr. Steel Res., 66(1), 11-18. https://doi.org/10.1016/j.jcsr.2009.08.002
  18. Jamaluddin, N., Lam, D., Dai, X.H., Ye, J. (2013). "An experimental study on elliptical concrete filled columns under axial compression." J. Constr. Steel Res., 87, 6-16. https://doi.org/10.1016/j.jcsr.2013.04.002
  19. Wei, Y. Wu, Y.F. (2014). "Compression behavior of concrete columns confined by high strength steel wire." Constr. Build. Mater., 54, 443-453. https://doi.org/10.1016/j.conbuildmat.2013.12.083
  20. Tiberti, G., Minelli, F., Plizzari, G. (2015). "Cracking behavior in reinforced concrete members with steel fibers: A comprehensive experimental study." Cem. Concr. Res., 68, 24-34. https://doi.org/10.1016/j.cemconres.2014.10.011
  21. Shim, H.B., Park, H.S. (2017). "Experimental tests on construction methods for a joint between concrete wall and steel girder involving long-time onsite welding." Constr. Build. Mater., 154(8), 600-608. https://doi.org/10.1016/j.conbuildmat.2017.08.001
  22. Li, G., Sun, F., Pang, M. Liu, W. Wang, H. (2016). "Structural Shear Wall Systems with Metal Energy Dissipation Mechanism." International Journal of High-Rise Building, 5(3), 195-203. https://doi.org/10.21022/IJHRB.2016.5.3.195
  23. Park, H.G., Kim, H.J., Park, J.Y. (2019) "Corner steel plate-reinforced core wall system." International Journal of High-Rise Building, 8(3), 193-199. https://doi.org/10.21022/IJHRB.2019.8.3.193
  24. GDL700E+ Industrial thermal image detector. http://hy4989.co.kr/mall/m_mall detail.php?ps_goid=8001.