• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.293-296
• /
• 2001

A conventional power supply to drive a microwave oven has ferro-resonant transformer and high voltage capacitor(HVC). Though it is simple, transformer is bulky, heavy and has low-efficiency. To improve this defect, a high frequency inverter type power supply has been investigated and developed in recent years. But, because of additional control circuit and switching device, inverter-type power supply is more expensive than conventional one. In this study, The design procedure of a novel HVC embedded high frequency transformer is proposed for down-sizing and cost reduction of Inverter-type power supply. Also, equivalent circuit mode] is derived by FEM analysis and impedance measurements. And the operation of proposed HVC embedded transformer is verified by simulations and experimental results.

• 한국전기전자재료학회논문지
• /
• 제33권4호
• /
• pp.326-330
• /
• 2020

Small-scale production control systems for smart manufacturing are becoming increasingly necessary as the manufacturing industry seeks to maximize manufacturing efficiency as the demand for customized product production increases. Correspondingly, the development of an embedded system to realize this capability is becoming important. In this study, we developed an embedded system based on an open source system that is cheaper than a widely applied programmable logic controller (PLC)-based production control system that is easier to install, configure, and process than a conventional relay control panel. This embedded system is system is based on a low-power, high-performance Cortex M4 processor and can be applied to smart manufacturing. It is designed to improve the development environment and compatibility of existing PLCs, control small-scale production systems, and enable data collection through heterogeneous communication. The real-time response characteristics were confirmed through an operation test for input/output control and data collection, and it was confirmed that they can be used in industrial sites.

• 드라이브 ㆍ 컨트롤
• /
• 제20권4호
• /
• pp.17-26
• /
• 2023

A forklift is an industrial vehicle that lifts or transports heavy objects using a hydraulically operated fork, and is equipped with an automatic transmission for the convenience of repetitive transportation, loading, and unloading work. The Transmission Control Unit (TCU) is a key component in charge of the shift control function of an automatic transmission. It consists of an electric circuit with an input/output signal interface function and firmware running on a microcontroller. To develop TCU firmware, the development process of shifting algorithm design, firmware programming, verification test, and performance improvement must be repeated. A simulator is a device that simulates a mechanical system having dynamic characteristics in real time and simulates various sensor signals installed in the system. The embedded transmission simulator is a simulator that is embedded in the TCU firmware. information related to the mechanical system that is necessary for TCU normal operation. In this study, an embedded transmission simulator applied to the originally developed forklift TCU firmware was designed and used to verify various forklift shift control algorithms.

• 정보처리학회논문지D
• /
• 제18D권1호
• /
• pp.45-56
• /
• 2011

저전력을 소모하는 임베디드 시스템 개발의 중요성이 증대되고 있다. 저전력 소모의 시스템 개발은 하드웨어 측면에서 많이 연구되어 왔지만, 소프트웨어의 동작이 하드웨어 전력 소모를 유발하기 때문에 소프트웨어의 소모 전력을 분석하는 것 또한 중요한 이슈중의 하나이다. 본 논문에서는 임베디드 소프트웨어 개발 과정에서 작성되는 설계 모델을 이용하여 에너지 효율적인 태스크 도출 방법을 제시한다. 이를 위하여 먼저 태스크 분할 기준을 제시하고, 이를 이용한 UML 설계 모델의 분할 과정을 설명한다. 제안된 태스크 도출 방법은 성능과 함께 전력 소모에 많은 영향을 미치는 임베디드 소프트웨어 개발에 활용하여 선행적으로 에너지 소모량을 절감할 기회를 제공할 수 있다.

• 제어로봇시스템학회논문지
• /
• 제15권4호
• /
• pp.420-425
• /
• 2009

In this paper, image detection and recognition algorithms are studied with respect to embedded carrier system. There are many suggested techniques to detect and recognize objects. But they have the propensity to need much calculation for high hit rate. Advanced and modified method needs to study for embedded systems that low power consumption and real time response are requested. The proposed methods were implemented using Intel(R) Open Source Computer Vision Library provided by Intel Corporation. And they run and tested on embedded system using a ARM920T processor by cross-compiling. They showed 1.6sec response time and 95% hit rate and supported the automated moving carrier system smoothly.

• 전력전자학회논문지
• /
• 제17권6호
• /
• pp.486-494
• /
• 2012

In this paper, we proposes the three-phase embedded Z-source inverter consisting of the three embedded Z-source converters and it's the output voltage control method. Each embedded Z-source converter can produce the bipolar output capacitor voltages according to duty ratio D such as single-phase PWM inverter. The output AC voltage of the proposed system is obtained as the difference in the output capacitor voltages of each converter, and the L-C output filter is not required. Because the output AC voltage can be stepped up and down, the boost DC converter in the conventional two-stage inverter is unnecessary. To confirm the validity of the proposed system, PSIM simulation and a DSP based experiment were performed under the condition of the input DC voltage 38V, load $100{\Omega}$, and switching frequency 30kHz. Each converter is connected by Y-connection for three-phase loads. In case that the output phase voltage is the same $38V_{peak}$ as the input DC voltage and is the 1.5 times($57V_{peak}$), the simulation and experimental results ; capacitor voltages, output phase voltages, output line voltages, inductor currents, and switch voltages were verified and discussed.

• Journal of Power Electronics
• /
• 제13권1호
• /
• pp.9-19
• /
• 2013

In this paper, a ripple input current embedded switched-inductor Z-source inverter (rESL-ZSI) and a continuous input current embedded switched-inductor Z-source inverter (cESL-ZSI) are proposed by inserting two dc sources into the switched-inductor cells. The proposed inverters provide a high boost voltage inversion ability, a lower voltage stress across the active switching devices, a continuous input current and a reduced voltage stress on the capacitors. In addition, they can suppress the startup inrush current, which otherwise might destroy the devices. This paper presents the operating principles, analysis, and simulation results, and compares them to the conventional switched-inductor Z-source inverter. In order to verify the performance of the proposed converters, a laboratory prototype was constructed with 60 $V_{dc}$ input to test both configurations.

• Journal of Electrical Engineering and Technology
• /
• 제9권2호
• /
• pp.390-398
• /
• 2014

The systematic optimal tuning of power system stabilizers (PSSs) using the dynamic embedded optimization (DEO) technique is described in this paper. A hybrid system model which has the differential-algebraic-impulsive-switched (DAIS) structure is used as a tool for the DEO of PSSs. Two numerical optimization methods, which are the steepest descent and Broyden-Fletcher-Goldfarb-Shanno (BFGS) algorithms, are investigated to implement the DEO using the hybrid system model. As well as the gain and time constant of phase lead compensator, the output limits of PSSs with non-smooth nonlinearities are considered as the parameters to be optimized by the DEO. The simulation results show the effectiveness and robustness of the PSSs tuned by the proposed DEO technique on the IEEE 39 bus New England system to mitigate system damping.

• 전기학회논문지P
• /
• 제53권4호
• /
• pp.190-194
• /
• 2004

In this paper, UPS, which is embedded in computer power supply, is developed against the poor utility power system. In the developed system, PIC16C54 is used as the main controller, and UPS system consists of micom control module, power failure detecting module, charging module, power module, synchronous transfer module, and GUI module. Additionally, GUI module consists of battery charging state unit, power operating unit and operating state unit. The effectiveness of the developed system has been verified by the experimental results.

• 한국산학기술학회논문지
• /
• 제15권8호
• /
• pp.5201-5206
• /
• 2014

본 논문에서는 블루투스 통신이 가능한 스마트 전등 스위치를 이용하여 안드로이드 스마트 폰을 이용한 전등 스위치 원격 제어를 구현 하였다. 스마트 전등 스위치는 임베디드 보드와 무선 통신을 이용하여 데이터를 송/수신하여 임베디드 보드에서 데이터를 종합 수집, 가공 하여 이 데이터를 다시 스마트폰과 무선통신을 이용하여 데이터를 송/수신 한다. 임베디드 보드를 게이트웨이로 이용함으로써 추후 추가 될 수 있는 센서들의 유연성을 보장 하였다. 이는 현재 신축 아파트 및 건물에서 서비스 중인 기능이지만, 이를 지원하지 않는 기존 가정에서도 스위치만 교환하여 사용이 가능하므로 사용자의 편의성과 시스템의 유연성을 보장한다.