• Journal of Multimedia Information System
• /
• v.5 no.1
• /
• pp.47-52
• /
• 2018

We have developed an electromagnetic generator to bury in subcutaneous area or abdominal cavity of the birds. As we can't use a solar battery, it is extremely difficult to supply a power for subcutaneous implantation such as biosensors under the skin due to the darkness environment. We are aiming to test the antigen-antibody reaction to confirm an avian influenza. One solution is a very small generator with the electromagnetic induction coil. We attached the developed coil to chickens and pheasants and recorded the electric potential generated as the chicken walked and the pheasant flew. The electric potential generated with physical simulator is equal to or exceeds the 7 V peak-to-peak at maximum by 560/min of flapping of wings. Even if we account for the junction voltage of the diode (200 mV), efficient charging of the double-layer capacitor is possible with the voltage doubler rectifier. If we increase the voltage, other problems arise, including the high-voltage insulation of the double-layer capacitor. For this reason, we believe the power generated to be sufficient for subcutaneous area of birds. The efficiency, magnetic 2 mm in length and coil 15mm in length, if axial direction is rectified, the magnetic flux density given to the coil could calculated to 7.1 % and generated power average 0.47mW. The improvements in size and wire insulation are expected in the future.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.339-339
• /
• 2007

Metal coating on ceramic powder has long been attracting interest for various applications such as superconductor where the brittle nature of high temperature ceramic superconductor was complemented by silver coating and metalloceramics where mechanical property improvement was achieved via electroless plating. More recently it has become of great interest in embedded passive device applications since metal coating on ceramic particles may result in the enhancement of the dielectric properties of ceramic-polymer composite capacitors. In our study, nickel ion-containing solution was used for coating commercial capacitor-grade $BaTiO_3$ powder. After filtering process, the powder was dried and heat-treated in 5% forming gas at $900^{\circ}C$. XRD and TEM were utilized for the observation of crystallization behavior and morphology of the particles. It was found that the nickel coating characteristics were strongly dependent on the several parameters and processing variables, such as starting $BaTiO_3$ particle size, nickel source, solution chemistry, coating temperature and time. In this paper, the effects of these variables on the coating characteristics will be presented in some detail.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.3
• /
• pp.312-320
• /
• 2019

In this paper, we design a 512Kb eFlash IP using 110nm eFlash cells. We proposed eFlash core circuit such as row driver circuit (CG/SL driver circuit), write BL driver circuit (write BL switch circuit and PBL switch select circuit), read BL switch circuit, and read BL S/A circuit which satisfy eFlash cell program, erase and read operation. In addition, instead of using a cross-coupled NMOS transistor as a conventional unit charge pump circuit, we propose a circuit boosting the gate of the 12V NMOS precharging transistor whose body is GND, so that the precharging node of the VPP unit charge pump is normally precharged to the voltage of VIN and thus the pumping current is increased in the VPP (boosted voltage) voltage generator circuit supplying the VPP voltage of 9.5V in the program mode and that of 11.5V in the erase mode. A 12V native NMOS pumping capacitor with a bigger pumping current and a smaller layout area than a PMOS pumping capacitor was used as the pumping capacitor. On the other hand, the layout area of the 512Kb eFlash memory IP designed based on the 110nm eFlash process is $933.22{\mu}m{\times}925{\mu}m(=0.8632mm^2)$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.28-28
• /
• 2010

This study realized low-temperature crystallization process of the $Ba_{0.6}Sr_{0.4}TiO_3$ (BST) thin films without thermal damage of substrate using excimer laser annealing (ELA) and structural and electrical characteristics were investigated. The amorphous BST thin films were prepared on Pt/Ti/$SiO_2$/Si substrate by sol-gel method at $250^{\circ}C$. The ELA was carried out using KrF excimer laser which provided excitation wavelength of 248 nm. The beam homogenizing system was used in order to homogenize beam shape of Gaussian fit. The XRD and SEM were used to analyze structural characteristics and the microwave capacitance, dielectric loss and tunability of the BST films were measured by a symmetrical stripline resonator method with shorted end. Consequently, the crystallinity of BST thin films were improved after ELA process and RF tunable capacitor was demonstrated at low temperature below $300^{\circ}C$.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.1
• /
• pp.12-21
• /
• 1999

All kinds of electronic machinery including portable communication system are being smaller size and are used at high frequency. It generates a lot of unwanted noise signals called electromagnetic interface (EMI). This paper presents an analysis result of EMI generation in VLSI and propose new circuits to minimize of EMI using I/O driver with parallel buffer architecture and distributed decoupling capacitor in a chip. The proposed circuits are evaluated with i8052 MCU which is shown reducing of delta current 1/3 times and improvement of EMI more 10dBuV compared with conventional processors.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.584-588
• /
• 2001

A conventional power supply to drive a microwave oven has ferro-resonant transformer and high voltage Capacitor(HVC). Though it is simple, transformer is bulky, heavy and has low-efficiency. To improve this defect a high frequency inverter type power supply has been investigated and developed in recent years. But, because of additional control circuit and switching device, inverter-type power supply is more expensive than conventional one. In this study, A new pulse power supply for Microwave Oven using novel HVC embedded high frequency transformer is proposed for down-sizing, cost reduction, and efficiency emprovement of Inverter type power supply. Also, equivalent circuit model is derived by impedance measurements. And the operation of proposed pulse power supply is verified by simulations and experimental results.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.446-450
• /
• 2007

It is strongly expected that inkjet printing method will be play and important role on printable electronics such as 3D integration of embedded ceramic devices(capacitor, resistor, inductor and electrode or circuit), Si-TFT and organic TFT including display C/F, RFID, FPCB, and etc. A inkjet printing method had been center of attention to strengthen the competitiveness of flat panel display on market and to open the new world of manufacturing process of printable electronics. We will survey the industrial tendency of printable electronics and flat panel display including some examples of inkjet printing and present the considerable points of inkjet printing method and some role of materials for successful inkjet printing.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.161-161
• /
• 2010

In order to achieve low power consumption and the uniform power spectrum of LED BLU (Back Light Unit) system, new circuits with a 2 stage L-C (Inductor-Capacitor) coupler have been proposed. From the simulation results based on our proposed model, the ripple power of the L-C regulation-embedded BLU circuit shows a dramatic reduction by more than 89.3% as compared to the normal BLU (without L-C circuits). This indicates that the proposed circuit is very promising for the realization of high-efficiency BLU circuits.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.3
• /
• pp.361-367
• /
• 2020

This paper proposes the battery-less ultra-low-power self-powered cooperating artificial neural networks device for embedded and IoT systems. This device can work without extraneous power supplying and can cooperate with other neuromorphic devices to build large-scale neural networks. This device has energy harvesting modules, so that can build a self-powered system and be used everywhere without space constraints for power supplying.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.322-322
• /
• 2008

Low-temperature co-fired ceramics (LTCC) have turned out to be very promising technology in accordance with the rapid developments in semiconductor technology. The demands for compact electrical assemblies, smaller power loss as well as high signal density can be fulfilled by LTCC. And for the multi-layered ceramic devices with embedded passive components such as high dielectric constant decoupling capacitor, LTCC materials require the several conditions to avoid delamination and internal cracks. For the present study, diopside-based glass is chosen as the LTCC substrate material in view of its high coefficient of thermal expansion (CTE). From the experimental resultsn the influence of each element on the CTE change can be revealed.