• 한국해양공학회지
• /
• 제11권3호
• /
• pp.20-28
• /
• 1997

The fatigue crack propagation properties and fatigue life of two kinds of Al body panel for automobile were examined experimentally by using the plate specimen and the single spot welding specimen. The fatigue limit of spot welding specimens was lower than that of a plate specimen. The fatigue limit was similar in two kinds of spot welding specimen. The shape and size of crack propagation were observed and measured on beach mark of fracture surface. The crack propagation of surface crack specimen showed almost same tendency to that of a thick plate as almost semi-elliptical. In spot welding specimen, the fatigue crack occurred in inside surface of nugget area was almost semi-elliptical. The crack growth rate can be explained using equation of stress intensity factors.

• 한국정밀공학회지
• /
• 제17권4호
• /
• pp.97-105
• /
• 2000

One of the most important steps to determine the blank shape and dimensions in deep drawing process is to calculate the surface area of the product. In general, the surface area of axisymmetric products is calculated by mathematical or graphical methods. However, in the case of non-axisymmetric products, it is difficult to calculate the exact surface area due to errors as separated components. Fortunately, it is possible for elliptical products to recognize the geometry of the product in the long side and short side by drafting in another two layers on AutoCAD software. So, in this study, a surface area calculating system is constructed for a design of blank shape of deep drawing products. This system consists of input geometry recognition module and three dimensional modeling module, respectively. The suitability of this system is verified by applying to a real deep drawing product. The system constructed in this study would be very useful to reduce lead time and cost for determining the blank shape and dimensions.

• 수산해양기술연구
• /
• 제21권2호
• /
• pp.99-104
• /
• 1985

In order to provide the basic data required for setting up the proper strategies to minimize the future marine pollution in the vicinity sea area of the Geoje Island, the general water quality parameters and dye diffusion experiment were carried out from January to March, 1983. Although TSS and COD level in the investigated sea area showed still slightly lower than the area of Seaside Industrial Complex Zones, seriously increasing due to the construction of heavy industrial plants. Dissolved oxygen showed more than 8 ppm, and inferred still enough for the reservation of the investigated sea area. The dye patches moved south-eastward with forming an elliptical shape and then turned slowly to the area of Kujora during flood tide, and it moved northwestward and then blocked the entrance of Jangseungpo during ebb tide, The diffusibility in the area may be assessed to be quite better than other coastal areas.

• 대한기계학회논문집A
• /
• 제36권6호
• /
• pp.609-615
• /
• 2012

레이저 충격 피닝 처리 시 레이저 광원으로부터 금속표면에 조사되는 레이저 빔 형상은 다양하다. 레이저 형상은 표면에서 발생하는 압력파의 특성을 결정하기 때문에 금속 표면과 깊이 방향에 대한 잔류응력 분포에 영향을 미칠 수 있다. 본 논문에서는 레이저 충격 피닝 처리시 레이저 광원 형상이 인코넬 alloy 600 합금의 잔류응력에 미치는 영향을 분석하였다. 레이저 광원 형상은 원형, 사각형, 타원형 형상이 고려되었으며, 표면과 깊이 방향에 대한 압축잔류응력 특성을 비교하였다. 표면에서 생성되는 압축잔류응력은 원형 레이저 형상이 최대이지만 중심부에서 인장응력이 발생하고, 깊이 방향에서는 타원형 레이저 형상이 최대 압축잔류응력을 생성한다. 소성변형 발생 깊이는 사각형에 비해 원형과 타원형이 양호하다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.63-65
• /
• 2005

In this study, the automatic face tracking algorithm is proposed by using the color and edge information of a color image. To reduce the effects of variations in the illumination conditions, an acquired CCD color image is first transformed into YCbCr color coordinates, and subsequently the morphological image processing operations, and the elliptical geometric measures are applied to extract the refined facial area.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.753-756
• /
• 2000

The accumulated know-how and trial-and-error procedures are known as the best ways to determine blank shape and dimensions. One of the most important steps to determine the blank shape and dimensions in deep drawing process is to calculate the surface area of the product. In general, the surface area of products is calculated by mathematical or 3-D modeling methods. A blank design system is constructed for elliptical deep drawing products to recognize the geometry of the product in the long side and short side by drafting in another two layers on AutoCAD software. This system consists of input geometry recognition module, 3-D modeling module and blank design module, respectively. Blank dimension of three types is determined by the same area, which was acquired in 3-D modeling module. The suitability of this system is verified by applying to a real deep drawing product.

• 한국의류학회지
• /
• 제14권4호
• /
• pp.292-304
• /
• 1990

The surface change of upperarm and shoulder blade area are caused by the extensive upper limb movement, thus it is necessary to measure the amount of change for constructing the clothing. Moire photography was taken after plastic casters of upperarm and shoulder blade area was prepared. 1. For the shoulder blade area, subjects showed the same change of surface area for the various limb positions, wherease, for the upperarm only at the $0^{\circ}\;and\;180^{\circ}$ limb position, same change was observed. 2. As the movement of the upperarm was increased, surface area of axillary part was increased and that of shoulder part was decreased. 3. To make a bodice pattern, the minimum size of the back with the ease were $\frac{B}{4}$+3.13 cm R for normal wear and $\frac{B}{4}$+5.75 cm for active wear. 4. As the movement of the arm was increased, the cross section for the upperarm were changed to elliptical shape. 5. For each horizontal basic line, there was a positive correlation between the amount of change of shoulder blad area and that of upperarm area.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1542-1547
• /
• 2007

Laser surface treatment technologies have been used to improve characteristics of wear and to enhance the fatigue resistance for mold parts. The optical lens with the elliptical profile is designed to obtain a wide surface hardening area with a uniform hardness. The objective of this research work is to investigate the influence of the process parameters, such as power of laser and defocused spot position, on the characteristics of laser surface treatment for the case of SKD61 steel and SCM4 steel. From the results of the experiments, it has been shown that the maximum average hardness is approximatly 700${\sim}$780 Hv when the power, focal position and the travel of laser are 1,095 W, 0mm and 0.3 m/min, respectively. In samples treated with lower scanning speeds, some small carbide particles appear in the interdendritic regions. This region contains fine martensite and carbide in proportions which depend on the local thermal cycle.

• 한국기계가공학회지
• /
• 제19권5호
• /
• pp.38-44
• /
• 2020

Surface texturing of micro-dimples has been used in many manufacturing industries to reduce friction between two sliding contacted surfaces. Surface texturing decreases the frictional force owing to minimizing of the sliding contact area. In this paper, micro-dimples have been fabricated on an Al6061-T6 surface using a two-frequency elliptical vibration texturing (TFEVT) method. A high-frequency of 18 kHz and low-frequency of 250 Hz were applied to an elliptically-vibrated tool holder. The Stribeck curve was plotted to analyze the friction coefficient trends. Furthermore, the representative wetting index, such as the water contact angle (WCA), was measured by considering the friction coefficient. WCA is associated with micro-dimple density and associated parameters. Consequently, the dimpled surfaces with a low friction coefficient exhibited a relatively high WCA in the feed direction. According to the Stribeck curve, the dimpled surfaces demonstrate superior friction performance for mixed-film lubrication compared to the non-textured surface.

• 한국정밀공학회지
• /
• 제22권11호
• /
• pp.51-58
• /
• 2005

Laser surface hardening technologies have been used to improve characteristics of wear and to enhance the fatigue resistance for automotive parts. The objective of this research work is to investigate the influence of the process parameters, such as power of laser and defocused spot position, on the characteristics of laser heat treatment for the case of SM45C medium carbon steel. CW Nd:YAG laser is selected as the heat source. The optical lens with the elliptical profile is designed to obtain a wide heat treatment area with a uniform hardness. From the results of the experiments, it has been shown that the maximum hardness is approximatly 780 Hv when the power and the travel speed of laser are 1,095 W and 0.6 m/min, respectively. In addition, the hardening width using the elliptical lens was three time larger than that using the defocusing of laser beam.