• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.270-273
• /
• 2000

For the well-preparation of the superconducting wire by electrophoresis, the control of the cracking on the YBCO, BSCCO superconductor deposited on Ag wire in acetone and buthanol solution with PEG(poly-ethylenglycol) was investigated with XRD and SEM analysis. After deposition, drying and heat treatment process, the cracks on the deposited surface of YBCO and BSCCO samples was clearly removed and decreased, which was perpared in suspension with addition of PEG from 1 to 3ml. However, in the case of the addition rate of PEG in acetone suspension was exceeded in 3ml, BSCCO superconductor deposited on Ag wire was slightly melted at 90$0^{\circ}C$ which was the same heat treatment condition of other samples with different additin rate of PEG. In the process of electrophoretic deposition, drying and heat treatment, PEG added into the suspension solution as a binder was very useful to prepare the crack-free thick film-wire of YBCO and BSCCO.

• Journal of the Korean Ceramic Society
• /
• v.53 no.1
• /
• pp.87-92
• /
• 2016

Due to its stability at high temperature and its layered structure, $Ti_3SiC_2$ MAX phase was considered to the interphase of $SiC_f/SiC$ composite. In this study, $Ti_3SiC_2$ MAX phase powder was deposited on SiC fiber via the electrophoretic deposition (EPD) method. The Zeta potential of the $Ti_3SiC_2$ suspension with and without polyethyleneimine as a dispersant was measured to determine the conditions of the EPD experiments. Using a suspension with 0.03 wt.% ball milled $Ti_3SiC_2$ powder and 0.3 wt.% PEI, $Ti_3SiC_2$ MAX phase was successfully coated on SiC fiber with an EPD voltage of 10 V for 2 h. Most of the coated $Ti_3SiC_2$ powders are composed of spherical particles. Part of the $Ti_3SiC_2$ powders that are platelet shaped are oriented parallel to the SiC fiber surface. From these results we expect that $Ti_3SiC_2$ can be applied to the interphase of $SiC_f/SiC$ composites.

• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.509-513
• /
• 2020

The performance of TiO₂ microcones/CNT composites as an anode material for lithium ion batteries was investigated. TiO₂ microcones/CNT composites were prepared by the polarization followed by electrophoretic deposition approaches on anodic TiO₂ microcones, which were composed of individual nanofragments resulting in a large surface area where lithium ion can be stored. Compared to pristine TiO₂ microcones, TiO₂ microcones/CNT composite electrodes showed higher areal capacity with a stable cyclability due to an enhanced electrical and lithium ion conductivity. Furthermore, TiO₂ microcones/CNT composite electrodes exhibited good cycle life characteristics and excellent rate retention under a high current density of up to 20 C.

• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.366-373
• /
• 2015

Sol-gel binder was prepared by hydrolysis and condensation reaction using boehmite sol and methyltrimethoxysilane as a function of aging-time. The coating slurry was composed of a plate-shape alumina in the sol-gel binder for the EPD process, in which particles dispersed in the slurry were deposited on the electrode under an electric field due to the surface charge. We studied the effects of three parameters: the content of boehmite, the aging time, and the applied voltage, on the physical, thermal, and electrical properties of the hybrid composite films by EPD. The amount of boehmite was 10 ~ 20 wt% and the aging time was 0.5 ~ 72, with a fixed amount of plate-shape alumina of 10 wt%. The condition of applied voltage was 5 ~ 30 V with a distance of 2 cm between the electrode during the EPD process. We confirmed that a structure of hybrid composite films of well-ordered plate alumina was deposited on the substrate when the film was prepared using a sol-gel binder composed of 15 wt% boehmite with 1 hr aging time and EPD at 10 V. The process shows a weight loss of 7% at $500^{\circ}C$ in TGA and a breakdown voltage of 8 kV at $87{\mu}m$.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.6
• /
• pp.319-325
• /
• 2004

Fe thin films containing Si particles were prepared on metallic substrates by electrodeposition method in sulfate solutions and the content of codeposited Si particles in the films was investigated as a function of applied current density, the content of Si particels in the solution, solution pH, solution temperature and concentration of $FeSO_4$$7H_2$O in the solution. The amount of Si codeposited in the film was not dependent on the applied current density, solution pH and solution temperature, while it was dependent on the content of Si particles in the solution and the concentration of $FeSO_4$$7H_2$O in the solution. The amount of Si codeposited in the film increased with increasing content of Si particles in the solution but reached a maximum value of about 6 wt% when the content of Si particles in the solution exceeds 100 g/l. On the other hand, the content of Si codeposited in the film increased up to about 17 wt% with decreasing concentration of $FeSO_4$$7H_2$O in the solution. These results would be applied to the fabrication of very thin Fe-6.5 wt% Si sheets for electrical applications.

• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.335-341
• /
• 2011

Continuous SiC fiber-reinforced SiC-matrix composites ($SiC_f$/SiC) had been fabricated by electrophoretic infiltration combined with ultrasonication. Nano-sized ${\beta}$-SiC added with 12 wt% of $Al_2O_3-Y_2O_3$ additive and Tyranno$^{TM}$-SA3 fabric were used as a matrix phase and fiber reinforcement, respectively. After hot pressing at 5 different conditions, the density, microstructure and mechanical properties of $SiC_f$/SiC were characterized. Hot pressing at relatively severe conditions, such as $1750^{\circ}C$ for 1 and 2 h, resulted in a brittle fracture behavior due to the strong fiber-matrix interface in spite of their high flexural strength. On the other hand, toughened $SiC_f$/SiC composite could be achieved by hot pressing at milder condition because of the formation of weak interface in spite of the decreased flexural strength. These results proposed the importance of weak fiber-matrix interface in the fabrication of ductile $SiC_f$/SiC composite.

• Composites Research
• /
• v.23 no.3
• /
• pp.7-12
• /
• 2010

In order to increase the electrical conductivity and the mechanical properties of carbon fabric composites, multi-walled carbon nanotubes (MWCNTs) and carbon nanofibers (CNFs) were deposited on carbon fabrics by anodic and cathodic electrophoretic deposition (EPD) processes. In the cathodic EPD, carbon nano-particles and nano-sized Cu particles were simultaneously deposited on the carbon fabric, which gave a synergetic effect on the enhancement of properties as well as the degree of deposition. The hybridization of carbon nano-particles and micron-sized carbon fiber significantly improved the through-the-thickness electrical conductivity. In addition, both MWCNTs and CNFs were deposited onto the carbon fabric for multi-scale hybrid composites. Multi-scale deposition improved the through-the-thickness electrical conductivity, compared to the deposition of either MWCNTs or CNFs.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.118-120
• /
• 2009

태양전지는 무한한 차세대 청정에너지로 주목을 받으며 그 개발의 필요성이 높아지고 있다. 이중 염료 감응형 태양전지(Dye-Sensitized Solar Cells, DSSC)는 낮은 제조 단가와 높은 효율로 기존의 Si 태양전지를 대체할 새로운 방법으로 연구되고 있다. 염료감응태양전지에 사용되는 $TiO_2$는 광촉매 성질 및 전자 전도성이 좋으며, 무독성에 가격이 저렴하여 다양한 분야에서 현재 많이 연구되고 있는 재료이다. 많이 사용되어지는 TiO2의 표면적은 염료의 흡착에 관여하므로 표면적의 제어는 매우 중요한 요소이다. $TiO_2$를 기판에 증착하는 방법으로는 Electrophoretic deposition, Chemical bath deposition, RF Margnetron sputtering, Electron-beam evaporation 등이 있으며 본 실험에서는 RF Magnetron sputtering을 사용하여 기판에 증착시키는 방법으로 구조를 제어하고자 한다. 이렇게 제조된 $TiO_2$ 박막을 SEM(Scanning Electron Microscopy)과 Solar simulator를 이용하여 표면형상과 Photocurrent-voltage curve를 분석하였다. 이것을 토대로 제조된 $TiO_2$박막의 구조가 염료감응태양전지에 미치는 영향을 연구해보고자 한다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.123-126
• /
• 2003

The electrophoretic deposition method using the suspension solution with additives under the electric potential was applied for the fabrication of YBCO superconductor wire. This method was able to simplify the fabrication facilities, and produce an uniform and dense thick film. To improve the critical current density of deposited films, the additive PEGs(Poly Ethylene Glycole) with the molecular weight of 600, 1000 and 3400, were used as chemical binders for the suspension solution. The organic additive PEG showed better effects to the properties of YBCO superconductor wire. The PEG improved the adhesion between superconductor particles and suppressed the crack on the surface, which enhanced the surface uniformity and density of YBCO deposited film. It was found that acetone suspension solution showed better deposition properties than the others. The samples fabricated in the solution with the additive, 8 vol.% of 1% PEG(1000), showed the highest critical current density measured as $2300{\sim}2400\;Acm^2$ at 77 K, 0 T.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.145-146
• /
• 2000

Primary emphasis was placed on the electrophoretic deposition of low voltage phosphor to indium-tin oxide-coated glass for the application of field emission display. The phosphor deposited by various parameters, such as deposition time and applied voltages was examined in detail. In addition, a comparison was made by analyzing luminance properties of the phosphor mixed with and without conducting $In_2O_3$ powder of less than 1um size. The measurement was performed as a function of $In_2O_3$ concentration from 3% to 15% by weight. The enhanced impact of indium powder mixing on the phosphor was clearly demonstrated by aging performance curve at 1000V excitation voltages with a current density of $1\;mA/cm^2$