• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.11
• /
• pp.912-917
• /
• 2001

In this study, we define the measuring method of crank angle precisely using an event and perform a study on the hardware structure and software algorithms which is applicable for the commercial engine. Also we developed a Computer-ECU(Personal computer based electronic control unit) using a computer and a microprocessor, for performing the ignition at a desire position(angle) and for controlling a duty ratio a pulse for ISC(Idle speed control). We applied these algorithms to the modeling which is induced a concept of event and got a better result than a conventional ECU in the state of transient as a result of performing air fuel ratio control in a commercial engine. This technique can be used for the back to improve ECU performance. It the present type of Hybrid I. C voltage regulator is altered to the new type of regulator, we will be surely able to reduce the production cost as well as simplify the design of alternator\`s rear bracket and rectifier part because of the removal of trio diode. Experiment is taken by MS-R004.

• Journal of Auto-vehicle Safety Association
• /
• v.11 no.1
• /
• pp.48-54
• /
• 2019

Optimal engine control is needed to cope with the global environmental regulations that are globally enforced. For optimum engine control, the electronic throttle control system (ETCS) is a prerequisite. Automotive makers are having an effect on reducing emissions and improving fuel economy by applying ETCS which is designed to secure stability. The ETCS controls the output of the throttle valve by passing the output value of the accelerator position sensor (APS) to the engine control unit (ECU). In this study, the authors investigated the safety standards of domestic and overseas accelerator control system and tried to understand how the air flow control affects the engine output by replacing the throttle. The authors suggest an improvement proposal of safety standard based on the result of driving evaluation by various modes.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.10
• /
• pp.898-906
• /
• 2002

Antilock Brake System (ABS) is designed to prevent wheels from being locked-up under emergency braking of a vehicle. Therefore it improves directional stability of the vehicle, shortens stopping distance, and enhances maneuvering during braking, regardless of road conditions. Hardware In-the-Loop Simulation (HILS) is an effective tool for design Performance evaluation and test of vehicle subsystems such as ABS, active suspension, and steering systems. This paper describes a HILS model for ABS/ ASR(Acceleration Slip Regulation) system applications. A fourteen degrees-of-freedom vehicle dynamics model is simulated in an alpha-chip processor board. The proposed HILS system is tested with a basic ABS control algorithm. The design and implementation of HILS system for the ABS ECU(Electronic Control Unit) development of commercial vehicle are presented. The results show that the proposed HILS system can be used to test the performance, stability, and reliability of a vehicle under braking.

• Journal of Convergence for Information Technology
• /
• v.9 no.7
• /
• pp.25-32
• /
• 2019

This paper proposes the method of an in-vehicle gateway to reduce the reprogramming time for the ECU (Electronic Control Unit). In order to reduce the reprogramming time, the gateway must prohibit transmitting messages, that are not related to reprogramming, to the destination CAN network, and no ECU should diagnose the DTC(Diagnostic Trouble Code) that indicates CAN communication error caused by prohibiting CAN messages by the gateway. Moreover, STmin, which are the minimum time between two consecutive CAN messages, should be minimized. In order to do this, this paper proposes the method that uses the link control command specified in UDS(Unified Diagnostic Services) and hardware based gateway functionality that are supported by the latest MCU(Micro Controller Unit). The proposed method is developed using TC275 based embedded system, and its results are presented.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.1172-1175
• /
• 2020

Automotive ECU integrates CPU core, IVN controller, memory interface, sensor interface, I/O interface, and so on. Current automotive ECUs are often developed with proprietary processor architectures. However, demends for standard processors such as ARM and RISC-V increase rapidly for saftware compatibility in autonomous vehicles and connected cars. In this paper, an automotive ECU is designed for parking assist system based on RISC-V with open instruction set architecture. It includes 32b RISC-V CPU core, IVN controllers such as CAN and LIN, memory interfaces such as ROM and SRAM, and I/O interfaces such as SPI, UART, and I2C. Fabricated in 65nm CMOS technology, its operating frequency, area, and gate count are 50MHz, 0.37㎟, and 55,310 gates, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.10a
• /
• pp.66-69
• /
• 2010

Lately, vehicle combined vehicle and IT(Information Technology) for vehicle's safety and convenience. so, vehicles is equipped with many ECU(Electronic control unit). the ECU's transmit data about each electronic control unit with OBD(On-Board Diagnostics) Network and data about each multimedia with MOST(Media Oriented System Transport) Network. In this paper, Supplementing disadvantage of existing blackbox, Using MOST of in-vehicle multimedia network and OBD-II of in-vehicle control network, blackbox system obtain the vehicle's driving state data. so, blackbox system judge vehicle's driving state and provide vehicle's driving state information to driver. Blackbox system implement the features mentioned above. as a result, blackbox is going to be more accurate blackbox system.

• Journal of IKEEE
• /
• v.21 no.3
• /
• pp.256-259
• /
• 2017

SENT (single edge nibble transmission) is a serial communication protocol between automotive sensors and ECU (electronic control unit). SENT exploits digital waveform, so it has a simple and cheap architecture without transceiver circuits. Usually it is exploited as an embedded communication interface in the sensors. In this paper, a SENT interface was designed in Verilog HDL, fully complying with SAE J2716. It was implemented in FPGA, and verified on a test board. When it was synthesized, the gate count is about 2,500 gates in 0.18um technology.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.4
• /
• pp.1915-1920
• /
• 2015

ISO 26262 is an international standard for the functional safety of electric and electronic systems in vehicles, and this standard has become a major issue in the automotive industry. In this paper, a functional safety compliant electronic control unit (ECU) for an electric power steering (EPS) system and a demonstration purposed EPS system are developed, and a software and hardware structure for a safety critical system is presented. EPS is the most recently introduced power steering technology for vehicles, and it can improve driver’s convenience and fuel efficiency. In conformity with the design process specified in ISO 26262, the Automotive Safety Integrity Level (ASIL) of an EPS system is evaluated, and hardware and software are designed based on an asymmetric dual processing unit architecture and an external watchdog. The developed EPS system effectively demonstrates the fault detection and diagnostic functions of a functional safety compliant ECU as well as the basic EPS functions.

• Journal of Welding and Joining
• /
• v.32 no.3
• /
• pp.74-80
• /
• 2014

Due to environmental regulations (RoHS, WEEE and ELV) of the European Union, electronics and automotive electronics have to eliminate toxic substance from their devices and system. Especially, reliability issue of lead-free solder joint is increasing in car electronics due to ELV (End-of-Life Vehicle) banning from 2016. We have prepared engine control unit (ECU) modules soldered with Sn-40Pb and Sn-3.0Ag-0.5Cu (SAC305) solders, respectively. Degradation characteristics of solder joint strength were compared with various conditions of automobile environment such as cabin and engine room. Thermal cycle test (TC, $-40^{\circ}C$ ~ ($85^{\circ}C$ and $125^{\circ}C$), 1500 cycles) were conducted with automotive company standard. To compare shear strength degradation rate with eutectic and Pb-free solder alloy, we measured shear strength of chip components and its size from cabin and engine ECU modules. Based on the TC test results, finally, we have known the difference of degradation level with solder alloys and use environmental conditions. Solder joints degradation rate of engine room ECU is superior to cabin ECU due to large CTE (coefficient of thermal expansion) mismatch in field condition. Degradation rate of engine room ECU is 50~60% larger than cabin room electronics.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.132-137
• /
• 2004

On-Board Diagnostic(OBD) systems are in most cars and light trucks on the load today. During the 1970's and early 1980's manufacturers started using electronic means to control engine functions and diagnose engine problems. The CARB's diagnostic requirements to meet EPA emission standards have been designated as OBD with a goal of monitoring all of the emissions-related components, as well as the chassis, body, accessory devices and the diagnostic control network of the vehicle for proper operation. In this paper, we present a remote measurement system for the wireless monitoring of diagnosis signal and sensors output signals of ECU adopted KWP2000, united the OBD communication protocol, on OBD-compliant vehicle using the wirless communication technique of Bluetooth. In order to measure the ECU signals, the interface circuit is designed to communicate ECU and designed terminal wirelessly according to the ISO, SAE regulation of communication protocol standard. A microprocessor S3C3410X is used for communicating ECU signals. The embedded system's software is programmed to measure the ECU signals using the ARM compiler and ANCI C based on MicroC/OS kernel to communicate between bluetooth modules using bluetooth stack. The diagnostic system is developed using Visual C++ MFC and protocol stack of bluetooth for Windows environment. The self-diagnosis and sensor output signals of ECU is able to monitor using PC with bluetooth board connected in serial port of PC. The algorithms for measuring the ECU sensor output and self-diagnostic signals are verified to monitor ECU state. At the same time, the information to fix the vehicle's problem can be shown on the developed monitoring software. The possibility for remote measurement of self-diagnosis and sensor signals of ECU adopted KWP2000 in embedded system verified through the developed systems and algorithms.