• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.2
• /
• pp.194-201
• /
• 2010

We propose a frequency selective surface(FSS) using double split ring resonators(DSRRs) for isolation enhancement between CDMA and RFID. The structure consists of an outer SRR and an inner SRR, and the gaps are formed in the same direction. By properly adjusting the gap and line width, the resonant frequency and skirt characteristics can be adjusted without varying the unit cell size. The proposed structure has a different field distribution from that of an ordinary SRR for magneto-dielectric materials. One layer consists of $9{\times}9$ unit cells and the other layer was separated by 50 mm. To validate the simulation results, we fabricated the patch antenna and the FSSs, and the measured results show a good agreement with the simulated ones. The electrical size of the unit cell is $0.110\;{\lambda}{\times}0.110\;{\lambda}{\times}0.002\;{\lambda}$, and the size of the two layer FSS is $1.058\;{\lambda}{\times}1.058\;{\lambda}{\times}0.153\;{\lambda}$. The two layer FSS maintain gain in CDMA frequency and has 6.9 dB reduced gain in RFID frequency.

• Korean Journal of Optics and Photonics
• /
• v.17 no.1
• /
• pp.7-17
• /
• 2006

In this paper, we proposed an optical true time-delay (TTD) for planar phased array antennas (PAAs), which is composed of a wavelength-dependent optical true time delay (WDOTTD) followed by a wavelength-independent optical true time delay (WIOTTD). The WDOTTD is a fiber Bragg gratings (FBGs) Prism and the WDOTTD is a fiber delay-lines matrix of which each component consists of a certain length of fiber connected to cross-ports of a 2${\times}$2 MEMS switch. A 10-GHz 2-bit${\times}$4-bit two-dimensional optical TTD has been fabricated by cascading a WDOTTD with a maximum time delay of 810 ps to a WIOTTD of $\pm$50 ps. Time delay and insertion loss for each radiation angle have been measured. Time delay error for the WIOTTD has been measured to be less than $\pm$1 ps. We have also designed a two-dimensional 10-GHz PAA composed of 8${\times}$8 microstrip patch antenna elements driven by the proposed TTD. The radiation patterns of this PAA have been obtained by simulation and analyzed.

• Journal of Advanced Navigation Technology
• /
• v.21 no.4
• /
• pp.353-358
• /
• 2017

In order to reduce the size of the previous stepped slot antenna for UWB applications(3.1 ~ 10.6 GHz) to half, an open ended stepped slot antenna is proposed. The proposed antenna consists of a stepped slot etched on the ground plane as radiation part and a microstrip feed-line with rectangular patch on the top plane for wideband impedance matching. The proposed antenna is designed and fabricated on the FR4 substrate with dielectric constant of 4.3, thickness of 1.6 mm and size of $28.5{\times}32mm^2$. The measured impedance bandwidth (${\mid}S_{11}{\mid}{\leq}-10dB$) of the fabricated antenna is 7.99 GHz(3.01~11 GHz) which is sufficient to cover UWB band (3.1 ~ 10.6 GHz). In particular, it has been observed that antenna has a good omnidirectional radiation patterns and high gain over the entire frequency band of interest even though the size of the proposed antenna is reduced to half when compared with the previous antenna.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2010.04a
• /
• pp.151-153
• /
• 2010

In this paper, the tri-band planar monopole microstrip antenna which stimulaneously meets the three bands such as TRS, WLAN and DMB is designed. The designed antenna size was smaller using CPW-fed structure that shows a ground-plane and a patch-plane are existed at one layer. The proposed antenna is designed on FR-4 substrate with a relative dielectric constant 4.3, thickness of 1.5mm and tangent loss 0.04. The designed antenna shows that VSWR is below 2 and has good return loss below -10dB over the three bandwidths.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.38 no.5
• /
• pp.498-508
• /
• 2001

In this paper, we propose an efficient coding algorithm for the zoom images to find the optimal depth and texture information. The proposed algorithm is the area-based method consisting of two consecutive steps, i) the depth extraction step and ii) the texture extraction step. The X-Y plane of the object space is divided into triangular patches and the depth value of the node is determined in the first step and then the texture of the each patch is extracted in the second step. In the depth extraction step, the depth of the node is determined by applying the block-based disparity compensation method to the windowed area centered at the node. In the second step, the texture of the triangular patches is extracted from the zoom images by applying the affine transformation based disparity compensation method to the triangular patches with the depth value extracted from the first step. To improve the quality of image, the interpolation is peformed on the object space instead of the interpolation on the image plane.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.5
• /
• pp.63-68
• /
• 2018

In this paper, We intended to design various things for the realization of SoS(System on Substrate) with SIW in 24GHz ISM 밴드(24-24.25GHz). As part of them, We integrated SIW, transition and MPAA as SoS on the same substrate and investigated its characteristics. We used Rogers Ro4350 with relative permittivity of 3.48 and thickness of 20mil. As results of optimal design, insertion loss of the SIW with 11.55mm length showed 0.32dB and insertion loss of 0.19dB occurred in transition to $50{\Omega}$ microstrip. Characteristics of the MPAA integrated on the same substrate as SoS are very similar to those of stand-alone MPAA. But the integrated MPAA decreased by 0.58dB in gain, which is the sum of SIW insertion loss and transition insertion loss, and by 0.7dB in SLL compared that of stand-alone MPAA. However, the bandwidth was increased by 19.4% as it changed from 670MHz to 800Mhz.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.1
• /
• pp.128-134
• /
• 2016

IoT devices including smart devices are connected with internet, thus they have security threats everytime. Particularly, IoT devices are composed of low performance MCU and small-capacity memory because they are miniaturized, so they are likely to be exposed to various security threats like DoS attacks. In addition, in case of IoT devices installed for a remote place, it's not easy for users to control continuously them and to install immediately security patch for them. For most of IoT devices connected directly with internet under user's intention, devices exposed to outside by setting IoT gateway, and devices exposed to outside by the DMZ function or Port Forwarding function of router, specific protocol for IoT services was used and the devices show a response when services about related protocol are required from outside. From internet search engine for IoT devices, IP addresses are inspected on the basis of protocol mainly used for IoT devices and then IP addresses showing a response are maintained as database, so that users can utilize related information. Specially, IoT devices using HTTP and HTTPS protocol, which are used at usual web server, are easily searched at usual search engines like Google as well as search engine for the sole IoT devices. Ill-intentioned attackers get the IP addresses of vulnerable devices from search engine and try to attack the devices. The purpose of this study is to find the problems arisen when HTTP, HTTPS, CoAP, SOAP, and RestFUL protocols used for IoT devices are detected by search engine and are maintained as database, and to seek the solution for the problems. In particular, when the user ID and password of IoT devices set by manufacturing factory are still same or the already known vulnerabilities of IoT devices are not patched, the dangerousness of the IoT devices and its related solution were found in this study.

• Korean Journal of Clinical Pharmacy
• /
• v.28 no.3
• /
• pp.224-229
• /
• 2018

Background: The patients receiving hematopoietic stem cell transplantation (HSCT) are known to have a high incidence of breakthrough nausea and vomiting due to the conditioning regimen. The purpose of this study was to evaluate the adequacy of antiemetic therapy for breakthrough nausea and vomiting in patients receiving HSCT and to propose an effective treatment regimen. Methods: We retrospectively reviewed the electronic medical records of 109 adult patients. The collected data were used to identify (1) antiemetic and dosing regimens prescribed for controlling breakthrough nausea and vomiting, (2) the rate of patients who developed breakthrough nausea and vomiting, and (3) the percent of antiemetics prescribed on the day of symptom onset. Based on the National Comprehensive Cancer Network guideline, we assessed the suitability of antiemetics for breakthrough nausea and vomiting, and prescription timing. Results: All patients were prescribed pro re nata antiemetics. About 40.0%, 41.4%, and 18.6% of patients were using one, two, and three or more additional drugs for breakthrough nausea and vomiting, respectively. The most frequently administered drugs were intravenous metoclopramide (43.8%) and granisetron patch (36.2%). Breakthrough nausea and vomiting occurred in 87 patients (79.1%) and they developed symptoms 320 cases. About 220 cases (68.8%) were treated with additional antiemetics on the day of symptom onset and the rate of symptom resolution was only 10.3% (9 patients). Conclusion: The breakthrough nausea and vomiting in patients receiving HSCT occurred very frequently and was hard to control, thus requiring more rapid and aggressive treatments.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.257-264
• /
• 2007

In this paper, we have designed and fabricated a wide-band and high gain antenna which can integrate a standard of IEEE 802.1la$(5.15\sim5.25\;GHz,\;5.25\sim5.35\;GHz,\;5.725\sim5.825\;GHz)$. We inserted a parallel dual slot into a rectangular patch to have wide-band, and we offset an element of capacitance from the slot by using coaxial probe feeding method. We also designed a converter of $\lambda_g/4$ impedance with taper type line so that wide-band impedance can be matched easily. We finally designed structure with $2\times2$ array in order to improve the antenna gain, and the final fabricated antenna could have a good return loss(Return loss$\leq$-10 dB) and a high gain(over 13 dBi) at the range of $5.01\sim5.95\;GHz(B/W\doteqdot940\;MHz)$.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.13 no.3
• /
• pp.219-222
• /
• 2007

In this paper, we have designed microstrip antenna of 800[MHz] band. It will be able to integrate TRS(Trunked Radio System), GSM(Global System for Mobile telecommunication) band including the CDMA(Code Division Multiple Access) band. we designed repeater and a base station antenna which is possible at the ship and marine of safety. It is improves a narrow bandwidth problem of microstrip antenna. It had L-shaped feeding structure at a rectangular patch and added the parallel L-slot that used a duplex resonance effect. Also for the improvement of profit the stack with the perpendicular. Designed frequency bandwith(VSWR 2:1) of the antenna showed good characteristic of 789${\sim}$1046[MHz] to 292[MHz](36%). Also the E-plan and H-plan all profit 6.4[dBi] above, the 3[dB] beam width showed the characteristic over the E-plan $44.7^{\circ} and H-plan $61.8^{\circ} to be improved.