• Membrane Journal
• /
• v.18 no.4
• /
• pp.282-293
• /
• 2008

Partially sulfonated poly(aryl ether sulfone) membranes were prepared from the sulfonated sulfone monomer, which was synthesized by a nucleophilic substitution, non-sulfonated monomers and potassium carbonate by a direct polymerization method and a subsequent solution casting technique with mixed solvents of N-methyl-2-pyrrolidone (NMP) and dimethylacetamide (DMAc). To investigate the effect of mixed solvent, the volume ratios of NMP and DMAc were varied in the range of $0{\sim}100%$ and the degrees of sulfonation of the copolymers were fixed as 50%. The surface properties of the resulting membranes were examined by scanning electron microscope (SEM) and atomic force microscope (AFM), and a comparative study of the morphology changes and the physicochemical properties such as proton conductivity and methanol permeability was achieved. It was found that proton conductivities depend on the volume ratio of NMP-DMAc mixed solvents, and the proton conductivity determined at the condition of $25^{\circ}C$ and 100% relative humidity was $1.38{\times}10^{-1}\;S/cm$ for the membrane prepared in the 50:50 v/v-% of NMP : DMAc mixed solvent.

• Journal of the Korean Chemical Society
• /
• v.42 no.6
• /
• pp.607-617
• /
• 1998

Au was dosed on $TiO_2(001)$ film grown epitaxially on Mo(100) surface in about 90 ${\AA}$ thickness. The growth mode of Au, thermal behavior and stability of the Au clusters, and the binding energy shift of Au 4f with the change in the amount of Au loading were studied by Auger Electron Spectroscopy (AES), Temperature Programmed Desorption (TPD) spectroscopy, Ion Scattering Spectroscopy (ISS), and X-ray Photoelectron Spectroscopy (XPS). Au grows three dimensionally on $TiO_2(001)$ film and the average size of Au clusters prepared at low temperature is smaller than those at higher temperature and the size increases with temperature irreversibly. Au clusters on $TiO_2(001)/Mo(100)$ start evaporation at 1000 K. TPD spectra of Au show very asymmetric peaks with the same leading edges irrespective of the amount of Au loading. The temperature at the peak maximum increases with the amount of Au. The desorption energy of Au obtained from the leading edge analysis of the TPD spectra is about 50 kcal/mol. The initial sticking coefficient of Au on $TiO_2(001)$ is constant in the temperature range of 200-600 K. The binding energy of Au 4f for the Au loaded on the film less than 2.0 MLE shifts to higher energy compared with the bulk Au. The shift is +0.3 eV at 0.1 MLE Au amount.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.8
• /
• pp.42-50
• /
• 2007

This paper presents design methods for dual-frequency(2.4/5.8GHz) active receiving antennas. The proposed active receiving antennas are designed to interconnect the output port of a wideband antenna to the input port of an active device of High Electron Mobility Transistor directly and to receive RF signals of 2.4GHz and 5.2GHz simultaneously where the impedance matching conditions are optimized by adjusting the length of $1/20{\lambda}_0$(@5.8GHz) CPW transmission line in the planar antenna The bandwidth of implemented dual-frequency active receiving antennas is measured in the range of 2.0GHz to 3.1GHz and 5.25GHz to 5.9GHz. Gains are measured of 17.0dB at 2.4GHz and 15.0dB at 5.2GHz. The measured noise figure is 1.5dB at operating frequencies.

• Journal of the Korean Ceramic Society
• /
• v.56 no.2
• /
• pp.178-183
• /
• 2019

A process of fabricating the foamed glass that has closed pores with 8 ~ 580 ㎛ sizes without a blowing agent by sintering 10 ㎛ boron-free glass powder composed of CaO, MgO, SO₃, Al₂O₃-83 wt% SiO₂ at a molding pressure of 0 ~ 120 MPa and a sintering temperature of 750 ~ 1000℃ was investigated. To analyze the glass transition temperature of glass powder, thermogravimetric analysis-differential thermal analysis (TGA-DTA) method were used. The microstructure and pore size of foamed glass were examined using the optical microscopy and field emission scanning electron microscopy (FE-SEM). For the thermal diffusivity and color of the fabricated samples, a heat flow meter and ultraviolet-visible-near-infrared (UV-VIS-NIR)-colormetry were used, respectively. In the TGA-DTA result, the glass transition temperature of glass powder was confirmed to be 626℃. In the microstructure result, closed pores of 7 ~ 20 ㎛ were formed at 750 ~ 900℃, and they were not affected by the molding pressure and sintering temperature. However, at 1,000℃, when there was 0 MPa molding pressure, closed pores of 580 ㎛ were confirmed, and the pore size decreased as the molding pressure increased. Moreover, at a molding pressure of 30 MPa or higher, closed pores of approximately 400 ㎛ were formed. The porosity showed an increasing trend of smaller molding pressure and larger sintering temperature, and it was controllable in the range of 5.69 ~ 68.45%. In the thermal diffusivity result, there was no change according to the molding pressure, and, by increasing the sintering temperature, up to 0.115 W/m·K could be obtained. The Lab color index (CIE-Lab) results all showed a similar translucent white color regardless of molding pressure and sintering temperature. Therefore, based on the foamed glass without boron and blowing agent, it was confirmed that white foamed glass, which has closed pores of 8 ~ 580 ㎛ and a thermal diffusivity characteristic of 0.115 W/m·K, can be fabricated by changing the molding pressure and sintering temperature.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.1
• /
• pp.1-5
• /
• 2006

Lithium titanium oxide $(Li_4Ti_5O_{12})$ with spinel-framework structures as anode material for lithium-ion battery was prepared by sol-gel and high energy ball milling (HEBH) method. According to the X-ray diffraction (XRD), Particle Size Analyses(PSA) and scanning electron microscopy (SEM) analysis, uniformly distributed $Li_4Ti_5O_{12}$ particles with grain sizes of 100 nm were observed. Half cells, consisting of $Li_4Ti_5O_{12}$ as working electrode and lithium foil as both counter and reference electrodes showed the high performance of high rate discharge capacity and 173 mAh/g at 0.2C in the range of $1.0\sim2.5 V$. Furthermore, the crystalline structure of $Li_4Ti_5O_{12}$ didn't transform during the lithium intercalation and deintercalation process.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.3 no.1
• /
• pp.164-175
• /
• 2000

Three compounds of Cu(II)-loaded N,N,N'-trimethylethylenediaminated Merrifield-type polymers were synthesized with yields higher than 80%, and the hydrolysis reaction rates of O-isopropylmethyl-phosphonofluoridate(GB) and O-pinacolylmethylphosphonofluoridate (GD) catalyzed by them have been surveyed. GB and GD hydrolysis by Cu(II)-loaded polymers occurs via intermediate complex mechanism where rapid equilibrium to form intermediate complex between substrate and Cu(II)-loaded polymers($K_f$) is followed by rate determining hydrolysis step($k_1$). The measured activation parameters for $k_1$ are ${\Delta}H^{\ddag}$ : $17.75{\pm}0.98kJ/mol$ ${\Delta}S^{\ddag}$ / : $-218.42{\pm}3.35J/mol$ K, $E^{\circ}_a$ : $20.22{\pm}0.98kJ/mo1$ for GB and ${\Delta}H^{\ddag}$ / : $11.16{\pm}1.15kJ/mol,$${\Delta}S^{\ddag}$ /: $-258.57{\pm}3.93J/mol$ K, $E^{\circ}_a$ : $13.64{\pm}1.15 kJ/mol$ for GD. Standard enthalpy/entropy changes corresponding to the intermediate complex formation constant $K_f$ are ${\Delta}H^{\circ}$ : $37.05{\pm}2.19 kJ/mo1,$$ {\Delta}S^{\circ}$ : $163.12{\pm}7.49 J/mol$ K and ${\Delta}H^{\circ}$ : 418.59{\pm}2.04 kJ/mol,$ ${\Delta}S^{\circ}$ : 4111.92{\pm}6.98 J/mol$ K for GB and GD, respectively, The electron push-pull mechanism by Cu(II)-loaded polymers lowers the P-F bond breaking energy(~400 kJ/mol) to less than 1/20 compared to the case in which no Cu(II)-loaded resin presents. Analysis of $K_f$ and 4k_1$ over pH=6.5~8.0 range suggest that the GB and GD hydrolysis occurs intramolecularily with $pK_a$ =7.29 for ligated $H_2O$ and $t_{1/2}$=36.9 sec, $pK_a$ = 7.06 and $t_{1/2}$=177.7 sec for GB and GD, respectively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.6
• /
• pp.225-231
• /
• 2016

The valence band maximum (VBM) and conduction band minimum (CBM) of Al-doped GaInAsSb alloys substrated on GaSb are calculated by using an analytic approximation based on the tight binding method. The relative positions of the VBM and CBM between Al-GaInASSb and GaSb determine band alignement type, valence band offset (VBO) and conductin band offset (CBO) for the heterojunctions. In this study, aluminium doping is assumed to be substituted in the cation site and limited up to 20 % because it can easily oxidize and degrade materials. It is found that the Al-doped alloys exhibit type-II band alignments over the entire composition range and make the band gaps increase, whereas the VBO and CBO decrease. The decreasing rate of VBO is higher than that of CBO, which implies the Al components play a decisive role in controlling electrons at the interface. The Al-dopled GaInAsSb alloy has a direct band gap induced by $E({\Gamma})$ with a considerable distance from the E(L) and E(X), however, $E({\Gamma})$ approaches to E(L) and E(X) in the high Sb concentration (Sb > 0.7-0.8) which might affect the electron mobility and degrade the optical quality.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.6
• /
• pp.261-265
• /
• 2010

In this paper, we attempt to improve the electrical characteristics of epoxy resin at high temperature (above $80^{\circ}C$) by adding magnesium oxide (MgO), which has high thermal conductivity. Scanning electron microscopy (SEM) of the dispersion of specimens with added MgO reveals that they are evenly dispersed without concentration. The dielectric breakdown characteristics of $SiO_2$ and MgO nanocomposites are tested by measurements at different temperatures to investigate the filler's effect on the dielectric breakdown characteristics. The dielectric breakdown strength of specimens with added $SiO_2$ decreases slowly below $80^{\circ}C$ (low temperature) but decreases rapidly above $80^{\circ}C$ (high temperature). However, the gradient of the dielectric breakdown strength of specimens with added MgO is slow at both low and high temperatures. The dielectric breakdown strength of specimens with 0.4 wt% $SiO_2$ is the best among the specimens with added $SiO_2$, and that of specimens with 3.0 wt% and 5.0 wt% MgO is the best among those with added MgO. Moreover, the dielectric strength of specimens with 3.0 wt% MgO at high temperatures is approximately 53.3% higher than that of specimens with added $SiO_2$ at $100^{\circ}C$, and that of specimens with 5.0 wt% of MgO is approximately 59.34% higher under the same conditions. The dielectric strength of MgO is believed to be superior to that of $SiO_2$ owing to enhanced thermal radiation because the thermal conductivity rate of MgO (approximately 42 $W/m{\cdot}K$) is approximately 32 times higher than that of $SiO_2$ (approximately 1.3 $W/m{\cdot}K$). We also confirmed that the allowable breakdown strength of specimens with added MgO at $100^{\circ}C$ is within the error range when the breakdown probability of all specimens is 40%. A breakdown probability of up to 40% represents a stable dielectric strength in machinery and apparatus design.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.2
• /
• pp.63-67
• /
• 2010

The organic solar cells with Glass/ITO/PEDOT:PSS/P3HT:PCBM/Al structure were fabricated using regioregular poly (3-hexylthiophene) (P3HT) polymer:(6,6)- phenyl $C_{61}$-butyric acid methyl ester (PCBM) fullerene polymer as the bulk hetero-junction layer. The P3HT and PCBM as the electron donor and acceptor materials were spin casted on the indium tin oxide (ITO) coated glass substrates. The optimum mixing concentration ratio of photovoltaic layer was found to be P3HT:PCBM = 4:4 in wt%, indicating that the short circuit current density ($J_{SC}$), open circuit voltage ($V_{OC}$), fill factor (FF) and power conversion efficiency (PCE) values were about 4.7 $mA/cm^2$, 0.48 V, 43.1% and 0.97%, respectively. To investigate the effects of the post annealing treatment, as prepared organic solar cells were post annealed at the treatment time range from 5min to 20min at $150^{\circ}C$. $J_{SC}$ and $V_{OC}$ increased with increasing the post annealing time from 5min to 15min, which may be originated from the improvement of the light absorption coefficient of P3HT and improved ohmic contact between photo voltaic layer and Al electrode. The maximum $J_{SC},\;V_{OC}$, FF and PCE values of organic solar cell, which was post annealed for 15min at $150^{\circ}C$, were found to be about 7.8 $mA/cm^2$, 0.55 V, 47% and 2.0%, respectively.

• Journal of the Korean Society of Radiology
• /
• v.8 no.7
• /
• pp.455-459
• /
• 2014

We grew the $Li_6Gd(BO_3)_3:Ce^{3+}$ scintillator and determined the scintillation and thermoluminescence properties for X-rays. The emission spectrum of $Li_6Gd(BO_3)_3:Ce^{3+}$ is located in the range of 370~500 nm, peaking at 423 nm an 455 nm, due to the $4f{\rightarrow}5d$ transition of $Ce^{3+}$ ions. The fluorescence decay time of the crystal is composed three components. The fast component is 60 ns (25%), the intermediate component is 787 ns (29%) and the slow component is $5.9{\mu}s$ (46%) of the crystal. The after-glow is caused by the electron and hole traps in the crystal lattice. We determined physical parameters of the traps in the crystal. The thermoluminescence trap are composed two traps. The determined activation energy (E), kinetic order (m) and frequency factor (s) of the first trap are 0.65 eV, 1.01 and $6.9{\times}10^8s^{-1}$. And, the determined activation energy, kinetic order and frequency factor of the second trap are 0.96 eV, 1.79 and $3.1{\times}10^{12 }s^{-1}$, respectively.