• Laser Solutions
• /
• v.8 no.1
• /
• pp.27-37
• /
• 2005

During laser spot welding of the braun tube electron gun, phenomena such as serious spattering and oxidative reaction, etc. were occurred. The spatter occurred from weld pool affects the braun tube, namely it blocks up a very small hole on the shadow mask and causes short circuit between two poles of the electron gun. We guessed that high power density and oxidative reaction are main sources of these problems. So, we studied to prevent and to reduce spatter occurring in spot welding of the braun tube electron gun using pulsed Nd:YAG laser. The characteristics of laser output power was estimated, and the loss of laser energy by optical parameter and spatter was measured by powermeter. The effects of welding parameters, laser defocused distance and incident angle, were investigated on the shape and penetration depth of the laser welded bead in flare and flange joints. From these results, the laser peak power was a major factor to control penetration depth and to occur spatter. It was found that the losses of laser energy by optic parameter and sticked spatter affect seriously laser weldability of thin sheets.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.6
• /
• pp.618-625
• /
• 2005

This paper has achieved that an optimal design and experiments of heater and cathode of electron gun that serve to embody high current density in CRT display. For the high brightness, high resolution and larger size in CRT display, high current density of electron gun is indispensible. An Impregnation style cathode is used, and must heighten operating temperature of heater to get high current density for this, it is proportional hereupon and power dissipation increases. In this paper, to get low power cathode with high current density, There are produced and tested sample that differ lead type of heater, coating method, the pitch and number of winding of the first and second coiling in the heat emission area for the low power design of high current density cathode heater in this paper.

• The Journal of Korean Institute of Information Technology
• /
• v.16 no.11
• /
• pp.43-49
• /
• 2018

Computer simulation was performed using the SIMION program to develop an electron gun for MCP cleaning. The target, MCP, is located 180mm from the source of the electron gun, and the diameter of the MCP is approximately 20mm. Therefore, we tried to find the condition that the beam diameter of electrons reaching the MCP is to be 20mm using four variables such as E, ${\phi}$, d1, d2, where the E is the energy of the electron reaching the MCP, the ${\phi}$ is the diameter of the extractor, and the d1 and the d2 are the distance from the electron source to the end of the extractor tube, and to the wall of chamber, respectively. As a result of simulation, we figuried out that the E and the d2 have little effect on the beam diameter. On the other hand, we also found that the beam diameters were very sensitive to the d1 and varied relatively large with respect to the ${\phi}$, and the d1 was the secondary order function of the ${\phi}$. Therefore we found that this function will allow us to design electron guns that are suitable for the purposes of this study.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.395-398
• /
• 2002

The spherical aberration and optical integer (f) of the electron gun's main lens in color CRT is obtained, using electron beam trajectory. A spherical aberration is obtained from the relation between the object plane and the image of a beam trajectory. To analyze beam profile, 3rd and 1st order coefficient were obtained and used. It is shown that, in practice, they are applied to electron gun design.

• Journal of Information Display
• /
• v.2 no.1
• /
• pp.43-46
• /
• 2001

To meet the demand of the display market for large, flat, high-resolution screen, the Super Common eXtended field Oval lens (S-CXO) has been developed with resolution improvement of 10% or more compared to a conventional electron gun. A new main lens structure is adopted, to enhance the effectiveness of aperture and the performance. The new main lens can be assembled using an existing assembly system

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.2
• /
• pp.86-89
• /
• 2013

Dye-sensitized solar cells have a FTO/$TiO_2$/Dye/Electrode/Pt counter electrode structure, yet more than a 10% electron loss occurs at each interface. A passivating layer between the $TiO_2$/FTO glass interface can prevent this loss of electrons. In theory, ZnO has excellent electron collecting capabilities and a 3.4 eV band gap, which suppresses electron mobility. FTO glass was coated with ZnO thin films by RF-magnetron sputtering; each film was deposited under different $O_2$:Ar ratios and RF-gun power. The optical transmittance of the ZnO thin film depends on the thickness and morphology of ZnO. The conversion efficiency was measured with the maximum value of 5.22% at an Ar:$O_2$ ratio of 1:1 and RF-gun power of 80 W, due to effective prevention of the electron recombination into electrolytes.

• Progress in Medical Physics
• /
• v.27 no.1
• /
• pp.25-30
• /
• 2016

The dosimetric characteristics were experimentally evaluated for electron beams from the prototype linac developed for radiotherapy units. This paper focuses on the electron beam output and energy variations as a function of electron gun heater current. The electron energy was derived from its mean and most probable energies measured by film dosimetry. The electron beam output at the maximum electron energy was measured with the plane parallel ionization chamber in water using TRS-398 dosimetry protocol. The mean energy and the most probable energy of the electron beam were 6.54~3.31 MeV and 5.94~2.80 MeV at electron gun current of 2.02~2.50 A respectively. The output dose rate for an electron beam of mean energy 6.54 MeV was 5.41 Gy/min ${\pm}1.5%$ at the reference depth in water.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.8
• /
• pp.719-731
• /
• 1991

This paper introduces a relatively simple computer simulation method for analyzing trajectory of electron beam in cylindrical electrode of the CRT, which outputs the cutoff voltag, beam current, spot size and plots out the trajectory, rom the input data on physical construction and applied voltages of electron gun. In order to improve computing speed in obtaining potential distibution, the authors have ivided the space into seveal setos and allocated different mesh sizes epending on the acuracy required to each sector and applied the finite difference method in calculation. The plot of trajectoy obtained from the simulation provided useful insight into the focusing mechanism of the CRT. The computed and measured result including beam curent. spot sizs and cutoff voltages for several model guns have ageed within eperimental error. The simulation program enables the designer to compare the effects of varied electrode shpe without the epense of building an actual gun and may be appli in esigning and implementing the electron gun assemply.

• Journal of Welding and Joining
• /
• v.20 no.4
• /
• pp.525-534
• /
• 2002

During laser spot welding of the braun tube electron gun, phenomena such as serious spattering and oxidative reaction, etc. were occurred. The spatter occurred from weld pool affects the braun tube, namely it blocks up a very small hole on the shadow mask and causes short circuit between two roles of the electron gun. We guessed that high power density and oxidative reaction are main sources of these problems. So, we studied to prevent and to reduce spatter occurring in spot welding of the braun tube electron gun using pulsed Nd:YAG laser. The characteristics of laser output power was estimated, and the loss of laser energy by optical parameter and spatter was measured by powermeter. The effects of welding parameters, laser defocused distance and incident angle, were investigated on the shape and penetration depth of the laser welded bead in flare and flange joints. From these results, the laser peak power was a major factor to control penetration depth and to occur spatter. It was found that the losses of laser energy by optic parameter and sticked spatter affect seriously laser weldability of thin sheets. The deepest penetration depth is gotten on focal position, and a "bead transition" occurred with a slight displacement of focal position relative to the workpiece surface and the absorption rate of the laser energy is affected by the shape factor of the workpiece. When we changed the incident angle of laser beam, the penetration depth was decreased a little with increasing of the incident angle, and the bead width was increased. The spattering was prevented by considering laser beam energy and incident angle.ent angle.

• Journal of the Korean Chemical Society
• /
• v.40 no.12
• /
• pp.719-723
• /
• 1996

An inverse photoemission spectrometer has been built and tested to study the unoccupied electron energy states of solid surfaces. It consists of a low energy electron gun and a band pass photon detector in an ultra-high vacuum chamber. The electron ray tracing simulation and current measurement of the electron gun show a good focus and a high flux of electron current. The overall resolution of the spectrometer is 0.74 eV and the sensitivity of the photon detector is about 10 counts/$sec{\cdot}{\mu}A.$ As a test experiment, the inverse photoemission spectra of a Ge(111) sample is in good agreement with the theoretical result.