• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.11 s.170
• /
• pp.2014-2021
• /
• 1999

The present investigation is concerned with the degradation characteristics of cast stainless steel(CF8M), exposed to the $\sigma$-phase degradation at $700^{\circ}C$. In the present paper, the degradation of CF8 M at $700^{\circ}C$ is evaluated by a non-destructive test, DL-EPR(double loop electrochemical potentiokinetic reactivation). The surface of specimens is observed by using scanning electron microscopy after DL-EPR test. Also. chromium contents of matrix, grain boundary and ferrite phase are analyzed by electron probe X-ray micro analyzer. Through the experiments, the following results are obtained 1) The degree of sensitization(DOS) of CF8M aged up to 15hr at $700^{\circ}C$ is increased with acing time while that is decreased with aging time from 15hr to 150hr. 2) The impact energy decreases with increase of $\sigma$-phase while DOS increases with $\sigma$-phase until aging time reaches to 15hr. After the aging time. 15hr, the $\sigma$-phase and the rate of impact energy with respect to aging time decreases. Therefore the degradation behavior of the CF8M can be evaluated by comparing SEM micrographs and the value of DOS.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.182-182
• /
• 1999

The chemisorption effect of CO on the Ni/Cu(001) surface was investigated using LEED(Low Energy Electron Diffraction) and EELS(Electron Energy Loss Spectrscopy0 under the UHV conditions. after mounting the Cu(001) single crystal in the UHV chamber (base pressure 1$\times$10-10Torr), a clean surface was obtained after a few cycles of repeated Ar+ ion sputtering and annealing at about 40$0^{\circ}C$. The epitaxial thin Ni films were formed on the Cu(001) by evaporation from 99.999% Ni block. The pseudomorphic growth and the orderness of the thin Ni films were monitored by c(2$^{\circ}C$2) LEED pattern. CO adlayers on Ni epitaxial thin films were prepared by dosing pure CO has through a leak valve. After CO adsorpton at room temperature, two pairs of peaks were observed by EELS, whose relative intensities are changed as the film thickness is varied and time is elapsed. These two pair of peaks are likely related to different bonding sites (-top and bridge sites) of C-Ni as well as C-O vibration. Experimental results and qualitative interpretation of the spectra wille be discussed. The possibility of using EELS in combination with probe species (CO) to investigate the nature of thin film growth is mentioned. We will report the experimental result of O2 dosage on Ni film and interaction of CO and O2.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.95-99
• /
• 2008

Cu has been used for metallic interconnects in ULSI applications because of its lower resistivity according to the scaling down of semiconductor devices. The resistivity of Cu lines will affect the RC delay and will limit signal propagation in integrated circuits. We investigated the electrolyte effects of the electroplating solution in the resistivity value of Cu films grown by electroplating deposition (EPD). The resistivity was measured with a four-point probe and the material properties were investigated with XRD (X-ray Diffraction), AFM (Atomic Force Microscope), FE-SEM (Field Emission Scanning Electron Microscope) and XPS (X-ray Photoelectron Spectroscopy). From these experimental results, we found that the electrolyte condition plays an Important role in formation of Cu film with lower resistivity by EPD.

• Journal of Welding and Joining
• /
• v.2 no.1
• /
• pp.4-17
• /
• 1984

Overlaid weld metals of austenitic stainless steel in a pressure vessel of power reactor are usually post-weld heated for a long period of time after welding. The PWHT is considered as a kind of sensitizing and it is important to check the soundness of the weld metal after PWHT, especially about the precipitation of carbides. The purpose of this report is to obtain information on the relation between the change of microstructure and Post-Weld Heat Treatment in the overlaid weld metals. Metallurgical aspects of the problem on austenitic stainless steel heated at $625^{\circ}C$, $670^{\circ}C$, $720^{\circ}C$ and $760^{\circ}C$ for 3, 10, 30, 100 and 300 hours have been investigated by means of optical-micrography, micro-hardness measurement, scanning electron microscope and electron-probe micro analysis. From the results obtained, the following conclusions are drawn; 1) The PWHT above $625^{\circ}C$ for a long time causes a diffusion of carbon atoms from low alloy steel into stainless steel, and consequently carbon is highly concentrated at the boundary layer of stainless steel. 2) C in ferritic steel migrated to austenitic steel and carbides precipitated in austenitic steel along fusion line. At higher temperatures, the ferrite grains coarsened in the decarburized zone. 3) In the change of microstructure of stainless steel overlaid weld metal, the width of carbides precipitated zone and decarburized zone increased with increase of PWHT temperature and time. 4) At about $625^{\circ}C$ to $760^{\circ}C$, chromium carbides, mainly $M_{23} C_6$, precipitate very closely in the carburized layer with remarkable hardening. 5) Precipitation of delta ferrite from molten weld metal depends on solidification phenomenon. There was a small of ferrite near the bond in which the local solidification time was short, comparing with after parts of weld metal. Shape and amount of ferrite were not changed by Post-Weld Heat Treatment after solidification.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.238-238
• /
• 2012

현재 국내 주얼리(gold alloy) 제품을 생산함에 있어 주조 방법은 크게 대기 중 주조(흡입주조) 방법과 진공주조 방법으로 나누어진다. 국내 주얼리 제조업체의 약 90%이상이 대기 중에서 주조하는 흡입주조방법을 통해 제품을 제작하고 있고, 국외의 경우, 대다수 진공주조방법을 통해 제품을 제작하고 있다. 본 연구에서는 주얼리 제품을 생산할 때 사용되는 합금재료(master alloy)가 동일한 조건에서 주조방법을 달리하여 각각 24개씩 총 48개의 14K yellow gold alloy 제품을 제작한 후 열처리를 통해 각각의 기계적, 물리적 특성분석을 비교 분석하였다. EPMA (Electron Probe Micro Analysis)분석을 통해 합금재료 및 제품의 구성성분을 조사하였고, ICP-MS (Inductively Coupled Plasma Mass Spectroscopy)를 사용하여 성분에 대한 정량분석을 실시하였다. 용체화처리(solid solution treatment)는 $700^{\circ}C$, 30분의 조건으로 실시하였고, 시효경화처리(age-hardening)는 $200{\sim}300^{\circ}C$의 온도범위에서 $50^{\circ}C$ 간격으로 실시하였다. 열처리 전과 후 시료의 grain 들의 배열 및 size 변화를 관찰하기 위해 식각 후 OM (optical microscope) 및 SEM (Scanning Electron Microscope)를 통해 분석하였다. 열처리 전 제품의 경도측정결과 대기 중 흡입주조방법 및 진공 주조방법을 통해 제작된 제품이 각각 119 Hv, 126 Hv로 나타났고, 용체화 처리 후 98 Hv, 92 Hv로 감소하였다. 시효경화 처리 후의 경도변화는 대기 중 흡입주조 및 진공주조방법을 통해 제작된 제품 모두 $270^{\circ}C$에서 각각 154 HV, 166 HV로 가장 높은 경도 값을 나타내었고, $270^{\circ}C$ 이상에서는 과시효(over aging)현상으로 인해 경도 값이 다시 감소하는 경향을 나타내었다. EPMA mapping 분석을 통해 주조방법에 따라 각각 제품의 구성성분분포도를 확인하였다. 이를 통해 열처리 전 다소 불균일하게 분포되었던 성분들이 열처리 후 균일해짐을 확인할 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.53-53
• /
• 2011

This paper describes results for surface and bulk characterization of the most promising thin film solar cell material for high performance devices, (Ag,Cu) (In,Ga) Se2 (ACIGS). This material in particular exhibits a range of exotic behaviors. The surface and general materials science of the material also has direct implications for the operation of solar cells based upon it. Some of the techniques and results described will include scanning probe (AFM, STM, KPFM) measurements of epitaxial films of different surface orientations, photoelectron spectroscopy and inverse photoemission, Auger electron spectroscopy, and more. Bulk measurements are included as support for the surface measurements such as cathodoluminescence imaging around grain boundaries and showing surface recombination effects, and transmission electron microscopy to verify the surface growth behaviors to be equilibrium rather than kinetic phenomena. The results show that the polar close packed surface of CIGS is the lowest energy surface by far. This surface is expected to be reconstructed to eliminate the surface charge. However, the AgInSe2 compound has yielded excellent atomic-resolution images of the surface with no evidence of surface reconstruction. Similar imaging of CuInSe2 has proven more difficult and no atomic resolution images have been obtained, although current imaging tunneling spectroscopy images show electronic structure variations on the atomic scale. A discussion of the reasons why this may be the case is given. The surface composition and grain boundary compositions match the bulk chemistry exactly in as-grow films. However, the deposition of the heterojunction forming the device alters this chemistry, leading to a strongly n-type surface. This also directly explains unpinning of the Fermi level and the operation of the resulting devices when heterojunctions are formed with the CIGS. These results are linked to device performance through simulation of the characteristic operating behaviors of the cells using models developed in my laboratory.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.333-333
• /
• 2011

We have investigated the breakdown properties in liquids by high voltage pulse system. High voltage pulse power system is consisted of the Marx-generator with two capacitors (0.5 ${\mu}F$, withstanding voltage is 40 kV), to which the charging voltage can be applied to maximum 30 kV DC, spark gap switch and charging resistor of 20 $M{\Omega}$. We have made use of tungsten pin electrodes of anode-cathode (A-K), which are immersed into the liquids. The breakdown voltage and current signals are measured by high voltage probe (Tektronix P6015A) and current monitor (IPC CM-1.S). Especially the high speed breakdown or plasma propagation characteristics in the pulsed A-K gap have been investigated by using the high speed ICCD camera. We have measured the electron temperature through the Boltzmann plot method from the breakdown spectrums. Here the A-K gap has been changed by 1 mm, 2 mm, and 3 mm. The used liquids are distilled water and solution of salt (0.9 %). The output voltage and current signals at breakdown in distilled water are shown to be bigger than those in saline solution. The breakdown voltage and current characteristics in liquids will be discussed in accordance with A-K gap distances. It is also found that the electron temperatures and plasma densities in liquids are decreased in conformity with A-K gap.

• Korean Journal of Materials Research
• /
• v.14 no.6
• /
• pp.389-393
• /
• 2004

The silicide layer used as a diffusion barrier in microelectronics is typically required to be below 50 nm-thick and, the same time, the silicides also need to have low contact resistance without agglomeration at high processing temperatures. We fabricated Si(100)/15 nm-Ni/15 nm-Co samples with a thermal evaporator, and annealed the samples for 40 seconds at temperatures ranging from $700^{\circ}C$ to $1100^{\circ}C$ using rapid thermal annealing. We investigated microstructural and compositional changes during annealing using transmission electron microscopy and auger electron spectroscopy. Sheet resistance of the annealed sample stack was measured with a four point probe. The sheet resistance measurements for our proposed Co/Ni composite silicide was below 8 $\Omega$/sq. even after annealing $1100^{\circ}C$, while conventional nickel-monosilicide showed abrupt phase transformation at $700^{\circ}C$. Microstructure and auger depth profiling showed that the silicides in our sample consisted of intermixed phases of $CoNiSi_{x}$ and NiSi. It was noticed that NiSi grew rapidly at the silicon interface with increasing annealing temperature without transforming into $NiSi_2$. Our results imply that Co/Ni composite silicide should have excellent high temperature stability even in post-silicidation processes.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.104.2-104.2
• /
• 2012

이종 재료의 접합에 대한 연구는 단일 재료에서 얻을 수 없는 물리적/기계적 특성과 이종 재료의 우수한 특성을 얻을 수 있다는 장점이 있어 국내외 적으로 연구가 활발히 진행되고 있다. 이러한 이종 접합 기술은 구조재료와 에너지 변환분야에 가장 많이 사용되고 있으며, 그 외 광촉매와 Thin film, 경량구조재료 등에도 사용되고 있다. 그 중 FGM(Functional Graded Materials)는 조성의 점진적인 변화를 통하여 접합하는 방법으로 이종 재료 접합 시 발생하는 내부 응력을 해소해줌으로써 적합한 방법이라고 할 수 있다. FGM 제작에 사용되는 방법으로 널리 알려진 것들로는 plasma spraying, 원심주조, 분말 야금법, PVD, CVD 그리고 EPD(electrophoretic deposition) 등이 있다. 이중에서 EPD는 수용액이나 유기용매와 같은 분산매체 중에 콜로이드 입자의 표면에 대전되는 전하를 이용하여, 외부에서 전장을 걸어서 입자의 움직임을 제어하는 기술이다 EPD는 코팅 속도가 상대적으로 빠르고 두꺼운 코팅 층 제작이 가능하다. 또한 바인더, 윤활제 또는 가소제를 사용하지 않고 다양한 종류와 모양의 기판 위에 균일한 코팅이 가능하다는 장점이 있다. 본 연구에서는 Ni substrate를 이용하여 그 위에 Ni과 $Al_2O_3$의 조성을 점진적으로 변화시켜 FGM을 EPD 방법으로 코팅하였다. 여기서 사용된 Ni은 높은 녹는점과 좋은 연성으로 인해 성형이 용이하여 구조재료로 적합하며, $Al_2O_3$는 고내열성과 내부식성을 가지며 경도가 높다는 장점이 있다. 본 연구에서는 EPD 방식을 이용하여 Ni/$Al_2O_3$ FGM을 코팅하였으며, 코팅 후 발생하는 substrate와의 접착력 문제를 해결하기 위해서 건조 방식과 substrate의 표면 상태를 최적화하여 다층의 Ni/$Al_2O_3$ FGM을 코팅 및 소결하였다. Zeta-potential 측정을 통해 electrophoretic mobility와 suspension의 분산 안정도를 평가 할 수 있었으며, X-ray 회절 분석(XRD)을 통하여 Ni 의 환원 여부를 확인하였다. 또한 Scanning electron microscopy(SEM) 분석을 통하여 미세구조 분석을 하였고, 최종적으로 Electron Probe Micro Analyzer (EPMA) 를 이용하여 다층 구조의 조성변화를 확인함으로 Ni/$Al_2O_3$의 FGM 코팅이 이루어졌음을 확인하였다.

• Journal of Korean society of Dental Hygiene
• /
• v.14 no.2
• /
• pp.281-286
• /
• 2014

Objectives : The aim of this study is to evaluate the surface changes of enamel specimen, tooth structure by toothpastes in child and adult. Methods : Experimental teeth were collected from extracted human primary teeth. 120 enamel specimens were prepared by cutting the teeth into $2{\times}3{\times}2mm$ blocks using diamond saw and the specimens were assigned to 3 groups. Group 1 was used as control with no treatment. Group 2 was treated with child toothpaste and Group 3 was treated with adult toothpaste on primary enamel surface for 3 minutes daily over 4 weeks. The specimens were immersed into individual container having artificial saliva and the artificial saliva was changed every day. The electron probe micro analyzer(EPMA) provided weight percent(wt%) of calcium(Ca) and phosphorous(P) on enamel surface. The morphology was analyzed by scanning electron microscopy(SEM). Data were analyzed by one-way analysis of variance(ANOVA) and Tukey's test post-hoc test using SPSS(Version 20, SPSS Inc., Chicago, USA). Level of significance was set at 0.05. Results : The surface changes of the primary teeth revealed a significant difference during 4 weeks. Calcium(Ca) and phosphorous(P) levels were found the weight percent difference and a rough enamel surface was seen on SEM after adult toothpaste application. Conclusions : The changes in Ca and P and the morphological surface were affected by the primary tooth treated with adult toothpaste. Enamel surface showed significant differences during 4 weeks.