• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.2
• /
• pp.151-154
• /
• 2020

Radiation noise due to EMI noise generated by the driving circuits of LED lighting devices in a medical imaging room was reduced by decreasing the noise source in the driving circuits and changing the number of corrections in EMI filters. Noise attenuation and filter changes enabled driving circuits that reduced the electromagnetic waves. Such circuits were efficiently designed by using capacitors and inverters in a given space. Therefore, the malfunction of radiation devices can be minimized by using EMI-reduction filter circuits, and reliable operation of medical devices can be expected by blocking electromagnetic waves.

• Journal of electromagnetic engineering and science
• /
• v.9 no.2
• /
• pp.53-60
• /
• 2009

Remarkable developments in the electric and electronic industry have given people's daily life much more convenience and abundance. However, in electrical communication, or electric and electronic fields, making electrical and electronic devices more functional, more integrated, and faster have put electromagnetic interference(EMI) into more complex forms, and lots of problems such as interruption, malfunction, or interference by noise between electrical communication systems occurs every day. In this research, the electromagnetic compatibility(EMC) filter in the high powered breaker was designed and fabricated as a counter measure. The filter attenuated noise more than 20${\sim}$50 dB in the range of 10 MHz${\sim}$1.5 GHz. And, when the electric fast transient(EFT) of 4 kV in the level 4 of IEC 61000-4-4 was induced, it was soon suppressed to 600 V.

• Journal of Magnetics
• /
• v.10 no.4
• /
• pp.163-170
• /
• 2005

The RF integrated noise filters are fabricated by photolithography. The stack for the electromagnetic noise filters consists of the nano-granular ($Co_{41}Fe_{38}AI_{13}O_8$) soft magnetic film / $SiO_2$ / Cu transmission line / seed layer (Cu/Ti) / $SiO_2$-substrate. A good signal-attenuation feature along with a low signal-reflection feature is observed in the present filters. Especially in the noise filter incorporated with a $Co_{41}Fe_{38}AI_{13}O_8$ magnetic film with lateral dimensions of $2000{\mu}m$ wide, 15 mm long and $1{\mu}m$ thick, the maximum magnitude of signal attenuation reaches -55 dB, and the magnitude of signal reflection is below -10 dB in the overall frequency range. And this level of signal attenuation is much larger than that of a noise filter incorporated with a Fe magnetic film.

• Journal of Korean Society for Quality Management
• /
• v.46 no.3
• /
• pp.379-396
• /
• 2018

Purpose: The purpose of this study was to propose a standard form of noise filter drawing, which is widely used in the field of weapon systems, to define the essential specification which is not standardized at the existing drawings and to employ the reference for manufacturing and qualification test. Methods: To do that, it identifies the improvements to analyze 19 noise filter drawings, studies the principle of noise filtering to find the essential part of the spec. and reviews the MIL-STD-220C and KS IEC 60939, which is the widely used as a formal spec. pertaining to the noise filter. Throughout the study, a standard form is developed to standardize the attenuation characteristics and find eight crucial metrics to specify the noise filter. Results: The results of this study are as follows; The standardized drawings can be used as the qualification test of the item and the manufacturing and engineering documents to make the noise filter, which are also applicable to the reference document to review KDS(Korea Defense Standard) drawings.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.552-559
• /
• 1998

Conducted noise in power line contains both the common mode(CM) and differential mode(DM) noise. These two modes of noise are caused by different noise sources and paths. Therefore, CM/DM noise must be deal with individually in EMI filter. In this paper the technique to separate power line noise is presented, which can be used to measure both the CM and the DM noise from total generated noise. Also, noise-separator is designed and experimental results showed 30 dB above of separation performance in 10 kHz~10 MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.8
• /
• pp.748-753
• /
• 2002

In this paper, a new topology of a active capacitor is proposed in order to apply the resonator in the design of RF active bandpass filters. Through the noise analysis of the active capacitor, the optimized low noise design process is also presented, Due to the low noise performance of the proposed active bandpass filter, it can be used in the RF front-end of the receivers. In designed 2-stage active bandpass filter at 1.9 GHz shows insertion loss of 0 dB, noise figure of 2.6 dB, and OIP3 of 8 dBm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.12
• /
• pp.963-968
• /
• 2018

In this paper, a compact common mode filter using passive elements is designed and fabricated. To design a common mode filter with required frequency response, the equivalent circuits of the common mode filter in differential mode and common mode were analyzed. Compared with the former filter using a ${\lambda}/4$ resonator, the size of the proposed structure was reduced by 60 %. The fabricated common mode filter has a maximum differential mode insertion loss of 1.2 dB and a minimum common mode absorption efficiency of 78.2% in the CMA - bandwidth of 27.5 %.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2016.05a
• /
• pp.176-176
• /
• 2016

• Journal of Industrial Technology
• /
• v.34
• /
• pp.71-78
• /
• 2014

Recently, using the electronic devices was increased with semiconductor developments. So, the EMI(Electromagnetic interference) problem become to important issue for coexistence with each electronic devices. The EMI is caused by switching operation from the power switches as the FET and the transistor in power conversion devices. In this paper, the hybrid EMI filter that composed with active components and passive components was described. The EMI filter is applied to the 160 watts LED driver experimentally verify the performance. The hybrid EMI filter is compared with non-filter, only passive filter and only active filter. The proposed EMI filter attenuated CM noise more than traditional passive filter.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.11
• /
• pp.1074-1080
• /
• 2013

The low phase noise and wideband frequency synthesizer has been designed by using YTO. Offset PLL structure is used for reducing a division ratio of feedback loop. The phase noise modeling is applied to optimize loop filter of PLL and YTO module. And DDS is used as reference signal of frequency synthesizer for fine resolution. The fabricated wideband frequency synthesizer has the output frequency of 3.2 GHz to 6.8 GHz, phase noise of -107 dBc/Hz at 10 kHz offset from the carrier and frequency resolution of 1 Hz. The measured phase noise is well agreed with the simulated one.