• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.2 no.4
• /
• pp.3-9
• /
• 1991

This paper presents the characteristics of antenna factors of half-wave resonance dipole antennas above a ground plane. The current distributions on a horizontal and vertical dipole antennas were analyzed by the Galerkin's method of moments, and these solutions are used for calculating the horizontal and vertical antenna factors above the ground plane. It is shown that accurate antenna factors of the horizontal and vertical dipole above the ground plane are required of the radiated emission test.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.319-323
• /
• 2000

A method for miniaturization of microstrip patch antenna without degrading its radiation characteristics is investigated. The ring geometry introduces additional parameters to the antenna that can be used to control its resonance frequency and bandwidth. For a single square ring increasing the size of patch decreases the resonance frequency and bandwidth. To match the antenna to a transmission line and also enhance its bandwidth. the square ring patch is stacked by a square ring patch. The computed results are compared with experiment and good agreement is obtained.

• Journal of electromagnetic engineering and science
• /
• v.4 no.3
• /
• pp.113-118
• /
• 2004

As an application of ring filters, a new and simple method to determine an inherent-ring-resonance frequency is introduced. The ring filter consists of a ring and two short stubs. They are connected at 90$^{\circ}$ and 270$^{\circ}$ points of the ring and the ring filter may be seen in such way that two filters are connected in parallel. Therefore, if the two powers of the two filters are out-of-phase at the output, the power excited at the input can not be delivered. That can be done by making difference in length of the two short stubs, and when a certain condition is satisfied, a frequency exists where all the excited power is reflected. That is the very inherent-ring-resonance frequency. In the lossless case, the return loss with the condition reaches 0 dB at the inherent-ring-resonance frequency but does not with conductor, dielectric losses and so on. Therefore, the effective loss tangent at a frequency of interest may be obtained correctly. To verify the method, two ring filters have been fabricated in microstrip lines and the measured results show good agreement with the predicted ones.

• Journal of electromagnetic engineering and science
• /
• v.11 no.3
• /
• pp.220-226
• /
• 2011

We have proposed a new method to accurately predict the resonance of Fabry-Perot Cavity (FPC) antennas enclosed with conducting side walls. When lateral directions of an FPC antenna are not blocked with metallic walls, the conventional technique is accurate enough to predict the resonance of the FPC antenna. However, when the FPC antenna has side walls, especially for case with only a short distance between the walls, the conventional prediction method yields an inaccurate result, inevitably requiring a tedious, time-consuming tuning process to determine the correct resonant height to provide the maximum antenna gain in a target frequency band using three-dimensional full-wave computer simulations. To solve that problem, we have proposed a new resonance prediction method to provide a more accurate resonant height calculation of FPC antennas by using the well-known resonance behavior of a rectangular resonant cavity. For a more physically insightful explanation of the new prediction formula, we have reinvestigated our proposal using a wave propagation characteristic in a hollow rectangular waveguide, which clearly confirms our approach. By applying the proposed technique to an FPC antenna covered with a partially reflecting superstrate consisting of continuously tapered meander loops, we have proved that our method is very accurate and readily applicable to various types of FPC antennas with lateral walls. Experimental result confirms the validness of our approach.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.640-645
• /
• 2020

To produce an input device stably using the transparent electromagnetic pattern of an electromagnetic induction method, pattern inspection is required in advance in the production process. Various methods of inspecting the capacitive pattern for hand-touch have been proposed, but it is difficult to find the related technical data for the pattern inspection method of the transparent electromagnetic induction method. In this study, to develop an inspection system for a fused electromagnetic resonance pen sensor with a copper-etched metal mesh pattern, an inspection algorithm and method for measuring the antenna impedance inside the sensor was proposed by measuring only the exposed FPCB connector. The proposed method was configured as a control board consisting of a microprocessor that forms a loop between specific channels according to the command of a computer, a computer-controlled by the Windows program, an LCR meter measuring the impedance between specific channels, and transmitting the measurement results back to the computer. An evaluation of the proposed system and measurements of nine specimens showed that it could detect the defects of the sensor used in the actual product.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.4
• /
• pp.277-282
• /
• 2014

Recently, much attention has been paid to nonlinear ultrasonic technology as a potential tool to assess hidden damages that cannot be detected by conventional ultrasonic testing. One nonlinear ultrasonic technique is measurement of the resonance frequency shift, which is based on the hysteresis of the material elasticity. Sophisticated measurement of resonance frequency is required, because the change in resonance frequency is usually quite small. In this investigation, the nonlinear electromagnetic acoustic resonance (NEMAR) method was employed. The NEMAR method uses noncontact electromagnetic acoustic transducers (EMATs) in order to minimize the effect of the transducer on the frequency response of the object. Aluminum plate specimens that underwent three point bending fatigue were tested with a shear wave EMAT. The hysteretic nonlinear parameter ${\alpha}$, a key indicator of damage, was calculated from the resonance frequency shift at several levels of input voltage. The hysteretic nonlinear parameter of a damaged sample was compared to that of an intact one, showing a difference in the values.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.5
• /
• pp.603-613
• /
• 1998

Resonant characteristic of Whispering modes(W. G. mode) on a dielectric disk resonator is influenced by an external circuit that is placed near the disk to excite this type of modes. In order to evaluate this phenomenon, we divide the disk resonator as two parts; a coupling part in which the mode coupling occurs and on uncoupled region. In the coupled part, we regard the part of the disk as a curved waveguide which is loaded with matched circuit, and derive a coupled mode equation for nonparallel dielectric waveguides. From the coupled mode equation, we calculate coupling coefficients and a coupled electromagnetic field. By using the complex coupling coefficients, we can calculate power transfer. We also calculate a resonant frequency in consideration of the mode coupling phenomenon. The calculated resonance frequence is confirmed by experiment for the resonance characteristics. As the results, it is found that the discrepancy between the theoretical and the experimental resonance frequencies is about 1.28% and the discrepancy between theory and experiment of FSR is about 0.6%.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.4
• /
• pp.225-230
• /
• 2004

An electromagnetic actuator has been designed and fabricated for Probe-based data storage applications. The actuator consists of permanent magnets(SmCo) housing and a media Platform which is connected to the Si frame by four couples of Si leaf springs. In order to generate electromagnetic force, Cu coils were electroplated under the media platform. The magnetic field distribution was calculated with 3D Finite Element Method of Maxwell 3D program. The field strength felt by Cu coils was estimated to be about 0.33T when the distance between the media platform and permanent magnets is $200\mu\textrm{m}$. The static and dynamic motions of the actuator were analyzed by FEM method with ANSYS 5.3. The measured displacements of the actuator were about $\pm$$92\mu\textrm{m}$ for input current of $\pm$40㎃ and the resonance frequency was 100Hz. The proposed electromagnetic actuator can be utilized for media driver of probe-based data storage system.

• Carbon letters
• /
• v.27
• /
• pp.90-97
• /
• 2018

Electromagnetic interference (EMI) shielding is an important issue in modern daily life due to the increasing prevalence of electronic devices and their compact design. This study estimated EMI-shielding effect (EMI-SE) of small ($8-14{\times}17mm$) Hanji (Korean traditional paper) doped with carbon nanotubes (CNTs) and compared to Hanji without CNT using $^2H$ (92.1 MHz) and $^{23}Na$ (158.7 MHz) nuclear magnetic resonance (NMR) peak area data obtained from 1 M NaCl in $D_2O$ samples in capillary tubes that were wrapped in the Hanji samples. The simpler method of using the variation of reflected power and tuning frequency by inserting the sample into an NMR coil was also tested at 242.9, 158.7, and 92.1 MHz. Overall, EMI shielding was relatively more effective at the higher frequencies. Our results validated that NMR methods to be useful to evaluate EMI-SE, particularly for small, flexible shielding materials, and demonstrated that EMI shielding by absorption is dominant in Hanji mixed with CNT.

• Journal of Power Electronics
• /
• v.17 no.4
• /
• pp.1058-1070
• /
• 2017

This paper proposes a novel active damping scheme to suppress LCL-filter resonance with only grid-current feedback control in grid-connected voltage-source converters. The idea comes from the concept of the model reference adaptive control (MRAC). A detailed theoretical derivation is given, and the effectiveness of this method is explained based on its physical nature. According to the control structure of this method, the active damping compensator, which is essentially a second order resonant integrator (SORI) filter, provides an effective solution to damp LCL resonance and to eliminate the need for additional sensors. Compared with extra feedback methods, the cost and complexity are reduced. A straightforward tuning procedure for the active damping method has been presented. A stability analysis is illustrated in the discrete domain while considering a one-step delay. Finally, experimental results are presented to validate the analysis and to demonstrate the good performance of the proposed method.