• Journal of Magnetics
• /
• v.21 no.1
• /
• pp.65-71
• /
• 2016

To increase the retaining force, a novel design for a concentric, bi-directional, electromagnetic valve actuator that contains double-layer permanent magnets is presented in this paper. To analyze the retaining-force change caused by the magnets, an equivalent magnetic circuit (EMC) model is established, while the EMC circuit of a double-layer permanent-magnet valve actuator (DLMVA) is also designed. Based on a 3D finite element method (FEM), the calculation model is built for the optimization of the key DLMVA parameters, and the valve-actuator optimization results are adopted for the improvement of the DLMVA design. A prototype actuator is manufactured, and the corresponding test results show that the actuator satisfies the requirements of a high retaining force under a volume limitation; furthermore, the design of the permanent magnets in the DLMVA allow for the attainment of both a high initial output force and a retaining force of more than 100 N.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.14 no.4
• /
• pp.471-477
• /
• 2014

In this paper, a modeling and co-simulation methodology is proposed to predict the radiated electromagnetic interference (EMI) from on-chip switching I/O buffers. The output waveforms of I/O buffers are simulated including the on-chip I/O buffer circuit and the RC extracted on-chip interconnect netlist, package, and printed circuit board (PCB). In order to accurately estimate the EMI, a full-wave 3D simulation is performed including the measurement environment. The simulation results are compared with near-field electromagnetic scan results and far-field measurements from an anechoic chamber, and the sources of emission peaks were analyzed. For accurate far-field EMI simulation, PCB power trace models considering IC switching current paths and external power cable models must be considered for accurate EMI prediction. With the proposed EMI simulation model and flow, the electromagnetic compatibility can be tested even before the IC is fabricated.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.7 s.98
• /
• pp.661-670
• /
• 2005

In this paper, the microstrip $90^{\circ}$ hybrid to provide -3dB coupling and $90^{\circ}$ phase difference at broadband frequency range of 2 to 6 GHz is designed. This proposed hybrid is composed of 3-section. The two outside section are realized by symmetrical edge coupled lines, but on the other hand the middle section consists of VIP(Vertically Installed Planar) circuit. The ground part of VIP circuit is partially removed to get tight coupling, particularly. This hybrid is easy to realize due to microstrip structure and has good holing flexibility by taking advantage of VIP circuit as a control point of optimization. The proposed hybrid provide satisfactory performance as compared with simplicity of structure and fabrication first of all.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.7
• /
• pp.1240-1246
• /
• 2000

The finite-difference time-domain (FDTD) method is applied to analyze a single step microstrip discontinuity in the substrate, and an equivalent circuit model comprised of two inductors and a capacitor has been developed using the numerical results. The microstrip discontinuity newly introduced in this paper has a thickness change of the substrate in the longitudinal direction with a uniform strip width. The discontinuity can be applied to the feeding circuit design for the patch antennas and interconnections between microwave circuit modules. The simulation results are compared with those computed by HFSS, and two results showed a good agreement. An equivalent circuit developed from the FDTD results, which is accurate within 2.4% in magnitudes of $S_{11}$ and $S_{21}$,can be applied for the computer-aided design of microwave circuits.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.924-929
• /
• 2009

In this paper, a dual-band MIMO antenna with a band stop matching circuit for next generation USB dongle application is proposed. The proposed multiband MIMO antenna consists of two dual-band PIFAs which provide wideband characteristics. In order to improve the isolation characteristic at the LTE(Long Term Evolution) band, a band stop matching circuit was inserted at the corner of each antenna element. The inserted band stop matching circuit is to suppress the surface current at the specific frequency band and to generate two additional resonances around 770 MHz for LTE band and near 830 MHz for digital communications network(DCN) service. The proposed MIMO antenna can cover LTE and DCN services, simultaneously.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.9
• /
• pp.875-880
• /
• 2011

We design and analyze the cloaking circuit using 2D transmission line structure to make up for the weakness of the established cloaking circuit using only lumped inductor and capacitor elements. The 2D transmission line structure enables one to conveniently design the cloaking circuit with available element values. All the necessary analysis and synthesis(design) formulas have been derived. A cloaking circuit for a cylindrical scatterer in free space has been designed based on the provided design formulas and its effects have been investigated using the circuit simulator ADS. The effect of the cloaking medium for this specific case has been observed to be about 10.5 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.10
• /
• pp.1121-1127
• /
• 2010

This paper describes the equivalent circuit of $45^{\circ}$ layer, one of $11.25^{\circ}$, $22.5^{\circ}$, and $45^{\circ}$ phase shift layers, which are needed for X-band Radant lens 4-bit phase shifter. The equivalent circuit is extracted by comparing the CST's MWS results with the Agilent's ADS results for $45^{\circ}$ phase shift layer. The simulated result is compared with the measured one. Using the extracted equivalent circuit, the phase bit simulation results of 4-bit Radant lens are also presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.10 s.89
• /
• pp.1005-1010
• /
• 2004

An analysis method of slot-coupled microstripline to waveguide transition is presented to developed a simple but accurate equivalent circuit model. The equivalent circuit consists of an ideal transformer, microstrip open stub, and admittance elements looking into a waveguide and a half space of feed side from a slot center. The related circuit element values are calculated by applying the reciprocity theorem, the Fourier transform and series representation, the complex power concept, and the spectral-domain immittance approach. The computed scattering parameters are compared with the measured, and good agreement validates the simplicity and accuracy of the proposed equivalent circuit model.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.7
• /
• pp.1048-1056
• /
• 2001

Decoupling capacitors are commonly used to reduce the effect of SSN propagated through parallel power and ground planes in high-speed multilayer printed circuit boards (PCBs). In this paper, we introduced a simple high frequency measurement and proposed a wideband (50 MHz ∼3 GHz) equivalent circuit model for decoupling capacitor considering high frequency parasitic effects. The proposed model can be easily combined with the SPICE model of power supply planes far SSN analysis. The circuit simulations with the proposed model show good agreement with the measurement results. Also, we expect to accurately analyze the noise reduction effect as a function of value and location using the proposed model of decoupling capacitor.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.3
• /
• pp.223-228
• /
• 2010

In this paper, temperature compensation circuit for the X-band voltage controlled oscillator(VCO) is presented by using the temperature sensor with the OP-AMP circuit. The frequency drifting by the temperature could be compensated by applying the tuning voltage which include the linearly changing output voltage of the temperature sensor. As a result, the frequency variation is reduced to 6.6~4.4 MHzfrom the 71~73 MHz variation with the compensation circuit over -30~+$60^{\circ}C$ range, when VCO is operated in the frequency range of 9.95~10.05 GHz.