• Journal of the Korean institute of surface engineering
• /
• v.18 no.4
• /
• pp.164-183
• /
• 1985

The microstructure of the zinc electrodeposits was investigated by changing the flow rate of electrolyte in zinc sulfate Bath. The cathode current efficiency increased with increasing flow rate of electrolyte. The preferred orientation of zinc electrodeposit changed from (11.2) texture to (10.3) or (10.1)+(10.2) texture with increasing current density in the range of flow rate, 0.2-1.2m/sec. The morphology of the deposits changed from the sponge deposit to the blocks of hexagonal crystallites packed together through the structures of find polycrystallite with increasing current density. The microstructure of the cross-section of the above deposits are granular structure and columnar structure respectively. The surface roughness of zinc electrodeposits decreased with increasing current density and flow rate of electrolyte.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.10
• /
• pp.1047-1048
• /
• 2000

Dye-sensitized nanocrystalline rutile $TiO_2$ solar cells were prepared, and the influence of Li+ and 1,2-dimethyl-3-hexyl imidazolium ions in the electrolyte on the photovoltaic properties was compared. The electrolyte con-taining Li+ ions produced a lower open-circuit photovoltage than the electrolyte with 1,2-dimethyl-3-hexyl im-idazolium ions, suggesting that the adsorption of Li+ ions to the rutile $TiO_2$ surface causes a shift in the band edges toward more positive potentials. At the same time, both the short-circuit photocurrent and the maximum value of the incident-photon-current conversion efficiency (IPCE) of the electrolyte containing Li+ ions were relatively higher. Data analysis suggests that presence of adsorbed Li+ ions improves via the phenomenon of band-edge movement the charge-injection efficiency by altering both the energy and number of excited state levels of the dye that participate in electron injection.

• Composites Research
• /
• v.29 no.6
• /
• pp.395-400
• /
• 2016

Recently, many research groups have studied on the epoxy-based multifunctional electrolyte to develop the structural composite bearing high mechanical properties without sacrificing the ionic conductivity at the same time. The studies on the optimal content and material selection for structural electrolyte have been published, while its curing behavior has not much analyzed yet. In this study, epoxy-based structural electrolyte containing solid electrolyte was prepared by varying the curing temperature and time. In addition, the ionic conductivities and mechanical properties of specimens were measured. We also find out the optimal hardening condition where the epoxy domain enables to be hardened within the range of temperature at which the thermal decomposition of electrolyte does not occur. Finally, we propose the multifunctional structural electrolyte showing achievable electrical and mechanical properties (282 MPa and $9{\times}10^{-6}S/cm@25^{\circ}C$).

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.4
• /
• pp.324-330
• /
• 2015

The electrolyte flow rates of vanadium redox flow battery play very important role in terms of ion transfer to electrolyte, kinetics and pump efficiency in system. In this paper a vanadium redox flow battery single cell was tested to suggest the optimization criteria of electrolyte flow rates on the efficiencies. The compared electrolyte circulation flow rates in this experimental work were 15, 30 and 45 mL/min. The charge/discharge characteristics of the flow rate of 30 mL/min was the best out of all flow rates in terms of charging and discharging time. The current efficiencies, voltage efficiencies and energy efficiencies at the flow rate of 30 mL/min were the best. The IR losses obtained at thd current density of $40mA/cm^2$, at the flow rates of 15, 30 and 45 mL/min were 0.085 V, 0.042 V and 0.115 V, respectively. The charge efficiencies at the current density of $40mA/cm^2$ were 96.42%, 96.45% and 96.29% for the electrolyte flow rates of 15, 30 and 45 mL/min, respectively. The voltge efficiencies at the current density of $40mA/cm^2$ were 77.34%, 80.62% and 76.10% for the electrolyte flow rates of 15, 30 and 45 mL/min, respectively. Finally, the energy efficiencies at the current density of $40mA/cm^2$ were 74.57%, 77.76% and 73.27% for the electrolyte flow rates of 15, 30 and 45 mL/min, respectively. The optimum flow rates of electrolytes were 20 mL/min in most of operating variables of vanadium redox flow battery.

• Membrane Journal
• /
• v.22 no.3
• /
• pp.208-215
• /
• 2012

Gel polymer electrolyte membranes were prepared from blends of polyvinyl alcohol (PVA) and poly (acrylic acid) (PAA), by solution-cast technique. The PAA content in the blend varied from 30 to 80 wt%. With the gel polymer electrolyte membranes, Zn air batteries were fabricated. The gel polymer electrolyte membranes were characterized by means of stress-strain test, impedance test. The Zn air batteries were tested by current interrupt method and galvanostatic discharge method. The tensile strength and tensile modulus decreased with increasing PAA content in the gel polymer electrolyte membrane. On the other hand, the ionic conductivity increased with increasing PAA content. The effect of ionic conductivity trend of the gel polymer electrolyte membrane in the Zn air battery was confirmed through current interrupt method and galvanostatic discharge method experiments. The battery with higher PAA content gel polymer electrolyte membrane showed lower IR drop and higher discharge capacity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.10
• /
• pp.814-819
• /
• 2010

Porous carbon electrodes with wooden materials are manufactured by molding carbonized wood powder. Electrical properties of the interface for electrolyte and porous carbon electrode are investigated from viewpoint of NaCl electrolyte concentration, capacitance and complex impedance. Density of porous carbon materials is 0.47~0.61 g/$cm^3$. NaCl electrolytic absorptance of the porous carbon materials is 5~30%. As the electrolyte concentration increased, capacitance is increased and electric resistance is decrease with electric double layer effect of the interface. The electric current of the porous carbon electrode compared in the copper and the high density carbon electrode was improved on a large scale, due to a increase in surface area. The circuit current increased as the distance between of the porous carbon electrode and the zinc electrode decreased, due to increase in electric field. Experimental results indicated that the current properties of galvanic cell could be improved by using porous carbon electrode.

• New & Renewable Energy
• /
• v.3 no.1 s.9
• /
• pp.54-59
• /
• 2007

A sintering aid, $B_{2}O_{3}$ have been included into a $LiAlO_{2}$ electrolyte support by a tape casting method in order to reinforce mechanical strength of the support for molten carbonate fuel cells [MCFCs). Starting idea originates from the low melting point of $B_{2}O_{3}$ ($450^{\circ}C$), which can provide the low temperature consolidation of ceramic materials. The mechanical properties and the microstructure changes of the $B_{2}O_{3}$-included electrolyte support were examined by scanning electron microscope, mercury porosimetry, X-ray powder diffraction [XRD], high temperature differential scanning calorimeter and three-point bending strength measurement. The mechanical strength was clearly improved by addition of $B_{2}O_{3}$. The increase of mechanical strength results from the neck growth of a new $LiAlO_{2}$ phase between $LiAlO_{2}$ particles by the liquid phase sintering. Average pore size and porosity of the electrolyte support reinforced by addition of the sintering aid, $B_{2}O_{3}$, was $0.24{\mu}m$ and 59%, respectively which were suitable microstructure of a matrix for an application of MCFCs.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.04a
• /
• pp.220-224
• /
• 2009

The effect of addition of single and binary additives on the performance of dye-sensitized $TiO_2$ solar cells based on 1,2-dimethyl-3-propylimidazolium iodide (DMPII) in ethylene carbonate (EC) and gamma-butyrolactone (GBL) has been evaluated at different cell temperatures in the $30-120^{\circ}C$ range. The electrolyte containing a single additive, 2-(dimethylamino)-pyridine (DMAP) showed best performance, which showed further enhancement for an electrolyte containing binary additives, DMAP and 5-chloro-1-ethyl-2-methylimidazole (CEMI) in equal molar ratio. The performance of the dye sensitized solar cell (DSC) based on electrolyte containing binary additives were found to be better than an acetonitrile based electrolyte. The dependence of different photovoltaic parameters (Voc, Jsc, ff, n) of the DSC upon temperature has been studied over the $30-120^{\circ}C$ range and only a small decrease in conversion efficiency has been observed. Thus the electrolyte containing binary additives (DMAP, CEMI) in EC/GBL solvent and show better performance in the investigated temperature range ($30-120^{\circ}C$).

• Korean Journal of Materials Research
• /
• v.9 no.6
• /
• pp.622-629
• /
• 1999

Effects of the fluorination in the $K_2$TiF\ulcorner solution and in-situ KF+ KOH electrolyte on the electrochemical charge-discharge properties of CaNi\ulcorner and the Mg-CaNi\ulcorner electrodes were investigated. In-situ fluorination in the KF+ KOH electrolyte compared with pre-fluorination in the$ K_2$TiF\ulcorner solution could improve the electrochemical cycling durability of CaNi\ulcorner and MG-CaN\ulcorner electrodes. The fluorinated layer on the alloy surface by pre-fluorination to improve the activity and anti-corrosion of the electrodes was dissolved in the pure KOH electrolyte during the cycling. The fluorinated layer was formed continuously on the surface of the electrode by thee2N KF addition in the 6N KOH electrolyte. The excess F\ulcorner ion addition in KOH electrolyte could improve the electrochemical cycling durability of CaNi\ulcorner and Mg-CaNi\ulcorner electrode. But, in case of MG-CaNi\ulcorner electrode, the discharge capacity of the electrode was reduced and the poor cycling property was shown with increasing of the MG process times.

• Composites Research
• /
• v.28 no.5
• /
• pp.285-290
• /
• 2015

Multiscale multiphysics in structural batteries make mechanical property testing difficult. In this research, the effect of electrolyte-coating on the mechanical performance of carbon fabric was studied using a suitable mechanical test method for structural batteries. For this experiment, two types of specimens were determined their dimension according to ASTM. One type of specimen was smaller than the standard dimension. The specimens were coated by spreading the electrolyte material on carbon fabric, hardened using epoxy, and tested for tensile properties using universal testing machine. As a result, it was found that the mechanical properties of carbon fabric were not influenced by electrolyte coating. In addition, the small-scale specimen used in this experiment was determined to be sufficiently reliable.