• 동력기계공학회지
• /
• 제4권2호
• /
• pp.31-39
• /
• 2000

Relationships between the plating condition and the plating rate of the deposition film for the electroless plating of Co-Cu-P alloy were discussed in this report. The result obtained from this experiment were summarized as follow ; The optimum bath composition was consisted of 0.8 ppm thiourea as a stabilizing agent. Composition of the deposit was found to be uniform after two hours of electroless plating. Plating rates of nickel-catalytic surface and zincate-catalytic surface were found to be very closely equal, but the plating time of nickel-catalytic surface took longer than that of the zincated-catalytic surface.

• 한국표면공학회지
• /
• 제40권3호
• /
• pp.131-137
• /
• 2007

The typical MCFC (molten carbonate fuel cell) anode is made of Ni-10%Cr alloy. The work of this paper is focused concerning long life of anode because Ni-10% Cr anode is suffering from sintering and creep behavior during cell operation. Therefore, Ni-coated Alumina powder($20{\mu}m$) was developed by electroless nickel plating. Optimum condition of electroless nickel coation on $20{\mu}m$ alumina is as follows: pH 11.7, temperature $65{\sim}80^{\circ}C$, powder amount $100cm^2/l$. The deposition rate for Ni-electroless plating was as a function of temperature and activation energy was evaluated by Arrhenius Equation thereby activation energy calculated slope of experimental data as 117.6 kJ/mol, frequency factor(A) was $6.28{\times}10^{18}hr^{-1}$, respectively.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 추계학술발표대회
• /
• pp.25.2-25.2
• /
• 2011

Recently, thin film capacitors used for vehicle inverters are small size, high capacitance, fast response, and large capacitance. But its applications were made up of liquid as electrolyte, so its capacitors are limited to low operating temperature range and the polarity. This research proposes using Ni-P alloys by electroless plating as the electrode instead of liquid electrode. Our substrate has a high aspect ratio and complicated shape because of anodic aluminum oxide (AAO). We used AAO because film thickness and effective surface area are depended on for high capacitance. As the metal electrode instead of electrolyte is injected into AAO, the film capacitor has advantages high voltage, wide operating temperature, and excellent frequency property. However, thin film capacitor made by electroless-plated Ni on AAO for full-filling into etched tunnel was limited from optimizing the deposition process so as to prevent open-through pore structures at the electroless plating owing to complicated morphological structure. In this paper, the electroless plating parameters are controlled by temperature in electroless Ni plating for reducing reaction rate. The Electrical properties with I-V and capacitance density were measured. By using nickel electrode, the capacitance density for the etched and Ni electroless plated films was 100 nFcm-2 while that for a film without any etch tunnel was 12.5 nFcm-2. Breakdown voltage and leakage current are improved, as the properties of metal deposition by electroless plating. The synthesized final nanostructures were characterized by scanning electron microscopy (SEM).

• 한국표면공학회지
• /
• 제47권5호
• /
• pp.269-274
• /
• 2014

Electroless plating process as a solution deposition method is a viable means of preparing conductive metal films on non-conducting substrates through chemical reactions. In the present study, the preparation and properties of electroless Ni-plating on flexible silicone rubber are described. The process has been performed using a conventional Ni(P) chemical bath. Additives and complexing agents such as ammonium chloride and glycine were added and the reaction pH was controlled by NaOH aqueous solution. Ni deposition rate and crystallinity have been found to vary with pH and temperature of the plating bath. It was shown that Ni-films having the high crystallinity, enhanced adhesion and optimum electric conductivity were formed uniformly on silicone rubber substrates under pH 7 at $70^{\circ}C$. The conductive Ni-plated silicone rubber showed a high electromagnetic interference shielding effect in the 400 MHz-1 GHz range.

• 자원리싸이클링
• /
• 제10권2호
• /
• pp.27-33
• /
• 2001

무전해 Ni-Cu-P폐 도금액의 재사용에 대해 소정의 조건에서 조사하였다. 아연화처리한 후 니켈 촉매의 처리는 니켈 촉매처리를 하지 않았을 때 보다 도금시간이 연장되었다 Batch type에서 새로 제조한 도금액에 폐 도금액을 50% 첨가하여도 무전해 Ni-Cu-P 폐 도금액의 재사용이 가능하였다. 새로 제조한 도금액에 소모된 도금액의 성분을 연속적으로 보충하여 도금하면(Continuous type), 보충하지 않았을 경우(B기ch type)보다 도금시간이 10배 연장되었다. 새로 제조한 도금액에 폐 도금액 50%를 첨가하여 소모된 도금액의 성분을 연속적으로 보충할 경우(Continuous type)의 도금시간은 보충하지 않았을 경우(Batch type)의 도금시간 보다 3.7배 연장되었다. 도금층의 불량과 급격한 도금속도의 감소는 도금층의 Ni과 Cu의 성분 변화에 큰 영향을 미쳤다.

• 자원리싸이클링
• /
• 제12권1호
• /
• pp.18-24
• /
• 2003

무전해 Ni-Cu-B 폐 도금액의 재사용에 대해 소정의 조건에서 조사하였다. 아연화처리한 후 니켈 촉매의 처리는 니켈 촉매처리를 하지 않았을 때 보다 도금시간이 연장되었다. Batch type에서 새로 제조한 도금액에 폐 도금액을 40% 첨가하여도 무전해 Ni-Cu-B 폐 도금액의 재사용이 가능하였다. 새로 제조한 도금액에 소모된 도금액의 성분을 연속적으로 보충하여 도금하면(continuous type), 보충하지 않았을 경우(batch type) 보다 도금시간이 6배 연장되었다. 새로 제조한 도금액에 폐 도금액 40%를 첨가하여 소모된 도금 액의 성분을 연속적으로 보충할 경우(continuous type)의 도금시간은 보충하지 않았을 경우(continuous type)의 도금시간 보다 2배 연장되었다. 도금층의 불량과 급격한 도금속도의 감소는 도금층의 Ni과 Cu의 성분 변화에 큰 영향을 미쳤다.

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 1999년도 제3회 총회 및 추계학술발표회
• /
• pp.35-35
• /
• 1999

• Journal of the Optical Society of Korea
• /
• 제19권3호
• /
• pp.217-221
• /
• 2015

Developing a metallization that has low cost and high efficiency is essential in solar-cell industries, to replace expensive silver-based metallization. Ni/Cu two-step metallization is one way to reduce the cost of solar cells, because the price of copper is about 100 times less than that of silver. Alkaline electroless plating was used for depositing nickel seed layers on the front electrode area. Prior to the nickel deposition process, 2% HF solution was used to remove native oxide, which disturbs uniform nickel plating. In the subsequent step, a nickel sintering process was carried out in $N_2$ gas atmosphere; however, copper was plated by light-induced plating (LIP). Plated nickel has different properties under different bath conditions because nickel electroless plating is a completely chemical process. In this paper, plating bath conditions such as pH and temperature were varied, and the metal layer's structure was analyzed to investigate the adhesion of Ni/Cu metallization. Average adhesion values in the range of 0.2-0.49 N/mm were achieved for samples with no nickel sintering process.

• 한국표면공학회지
• /
• 제18권4호
• /
• pp.153-163
• /
• 1985

In the electroless nickel plating bath which contained nickel sulfate, sodium hypophosphite, boric acid and triethanolamine, effect of their concentration on the rate of deposition was tested by gravimetric method and polarization method. The polarization method that polarize small range of voltage anodicaly and cathodicaly at the mixed potential in the electroless plating bath can calculate mixed current (depositing rate) from $i_{mp}=\frac {i}{\eta}\;\frac{RT}{nF}\;or\;i_{mp}=\frac{i}{\eta}\;\frac{1}{2.3}(\frac{b_a\;\;b_c}{b_c+b_a})$ Where $i_{mp}$ is the depositing current, i is the polarized current, ${\eta}$ is the polarized voltage, $b_a\;and\;b_c$ are the Tafel slop of anodic and cathodic polarization curves respectively. The calculated mixed current ($i_{mp}$) is proportional to the depositing rate obtained by gravimetric method and corresponded mostly to the real depositing rate by multifying supplementary constant. The polarization method can be used for founding inclination of reaction on various concentration of each composition. Decreasing or increasing concentration of triethanolaminc as a complexing agent , the depositing rate is decreased and when the bath contained 25-50mL/L of triethanoloamine, the depositing rate is increased. The depositing rate is increased with increasing the concentration of boric acid, and when the bath contained 0.5M of boric acid, the depositing rate is increased abruptly. The optimum composition of the electroless nickel bath was estimated 0.1M of nickel sulfate, 0.25M of sodium hypophosphite, 0.5M of boric acid, and 25-50mL/L of triethanalamine.

• 한국표면공학회지
• /
• 제44권6호
• /
• pp.246-249
• /
• 2011

Surface modification before coating nickel by coupling agents and/or etchant of glass did not provide enough adhesive strength of electroless nickel deposits on glass. Effect of heat treatments on hardness as well as adhesion of nickel deposits was studied by using tape test for adhesion, nanoindenter for hardness and glancing angle x-ray diffractometer (GAXRD) for phase characterization. Heat treatment improved hardness as well as adhesion. XRD results give that the improvements of adhesion and hardness are due to the formation of $NiSiO_4$ around the interface between the nickel deposits and the glass and the precipitation of $Ni_3P$ causing precipitation hardening, respectively. The details in effects of heat treatment on adhesion and hardness are described here.