• 한국표면공학회지
• /
• 제28권1호
• /
• pp.3-13
• /
• 1995

Electroless Ni and Cu platings were conducted on $B_4C$ and SiC. In the electroless Ni plating, the deposition rate on $B_4C$ was higher than on SiC. However, the electroless Cu deposition occured with high deposition rate regardless of the carbide substrates used in this study. Uniformity of the deposits was better in the electroless Cu deposition than in the electroless Ni deposition. In the topographies of the electroless depositions, Ni deposits have grown as colony, whereas Cu deposits have grown as fine individual grains.

• 한국전기전자재료학회논문지
• /
• 제11권12호
• /
• pp.1091-1098
• /
• 1998

Thermal stability of the electroless deposited Cu thin film was investigated. Cu/TaN/Si multilayer was fabricated by electroless-depositing Cu thin layer on TaN diffusion barrier layer which was deposited by MOCVD on the Si substrate, and was annealed in $H_2$ ambient to investigate the microstructure of Cu film with a post heat-treatment. Cu thin film with good adhesion was successfully deposited on the surface of the TaN film by electroless deposition with a proper activation treatment and solution control. Microstructural property of the electroless-deposited Cu layer was improved by a post-annealing in the reduced atmosphere of $H_2$ gas up to $600^{\circ}C$. Thermal stability of Cu/TaN/Si system was maintained up to $600^{\circ}C$ annealing temperature, but the intermediate compounds of Cu-Si were formed above $650^{\circ}C$ because Cu element passed through the TaN layer. On the other hand, thermal stability of the Cu/TaN/Si system in Ar ambient was maintained below $550^{\circ}C$ annealing temperature due to the minimal impurity of $O_2$ in Ar gas.

• 한국세라믹학회지
• /
• 제52권4호
• /
• pp.264-268
• /
• 2015

Cu films were plated in an eco-friendly electroless bath (No-Formaldehyde) on Ni/screen printed Ag pattern/PET substrate. For electroless Cu plating, we used sodium-phosphinate ($NaH_2PO_2{\cdot}H_2O$) as reducing agent instead of Formaldehyde. All processes were carried out in electroless solution of pH 7 to minimize damage to the PET substrate. According to the increase of sodium-phosphinate, the deposition rate, the granule size, and rms roughness of the electroless Cu film increased and the Ni content also increased. The electroless Cu films plated using 0.280 M and 0.575 M solutions of sodium-phosphinate were made with Cu of 94 at.% and 82 at.%, respectively, with Ni and a small amount P. All electroless Cu plated films had typical FCC crystal structures, although the amount of co-deposited Ni changed according to the variation of the sodium-phosphinate contents. From these results, we concluded that a formation of higher purity Cu film without surface damage to the PET is possible by use of sodium-phosphinate at pH 7.

• 한국재료학회지
• /
• 제23권11호
• /
• pp.661-665
• /
• 2013

We investigated the characteristics of electroless plated Cu films on screen printed Ag/Anodized Al substrate. Cu plating was attempted using neutral electroless plating processes to minimize damage of the anodized Al substrate; this method used sodium hypophosphite instead of formaldehyde as a reducing agent. The basic electroless solution consisted of $CuSO_4{\cdot}5H_2O$ as the main metal source, $NaH_2PO_2{\cdot}H_2O$ as the reducing agent, $C_6H_5Na_3O_7{\cdot}2H_2O$ and $NH_4Cl$ as the complex agents, and $NiSO_4{\cdot}6H_2O$ as the catalyser for the oxidation of the reducing agent, dissolved in deionized water. The pH of the Cu plating solutions was adjusted using $NH_4OH$. According to the variation of pH in the range of 6.5~8, the electroless plated Cu films were coated on screen printed Ag pattern/anodized Al/Al at $70^{\circ}C$. We investigated the surface morphology change of the Cu films using FE-SEM (Field Emission Scanning Electron Microscopy). The chemical composition of the Cu film was determined using XPS (X-ray Photoelectron Spectroscopy). The crystal structures of the Cu films were investigated using XRD (X-ray Diffraction). Using electroless plating at pH 7, the structures of the plated Cu-rich films were typical fcc-Cu; however, a slight Ni component was co-deposited. Finally, we found that the formation of Cu film plated selectively on PCB without any lithography is possible using a neutral electroless plating process.

• 마이크로전자및패키징학회지
• /
• 제15권2호
• /
• pp.17-21
• /
• 2008

Sn-Cu계 솔더 범프에서 무전해도금법을 이용한 범프 형성에 대한 연구를 하였다. $20{\mu}m$ via에 전기도금법으로 구리를 채운 웨이퍼 위에 ball형태의 범프를 형성하기 위하여 구리와 주석을 도금하여 약 $10{\mu}m$높이의 범프를 형성하였다. 구리 범프 형성 시 via위에 선택적으로 도금하기 위하여 활성화 처리 후 산세처리를 실시하고 무전해 도금액에 안정제를 첨가하였다. 무전해도금법을 이용하여 주석 범프 형성 시 도금층이 구리 범프에 비해 표면의 균일도가 벌어지는 것으로 관찰되었지만 reflow공정을 실시한 후 ball 형태의 균일한 Sn-Cu 범프를 형성하였다.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2001년도 The IMAPS-Korea Workshop 2001 Emerging Technology on packaging
• /
• pp.100-103
• /
• 2001

본 연구에서는 무전해도금으로 증착된 구리박막의 열적 및 접착특성에 관하여 고찰하였다. Si 기판에 MOCVD 방법으로 TaN 확산방지막을 증착한 후, 무전해 도금으로 구리박막을 증착하여 Cu/TaN/Si 다층구조를 제조공정하였다. 그리고, Ar 분위기에서 열처리시켰으며, 열처리온도에 따른 비저항 변화를 고찰함으로서 Cu/TaN/Si 계의 열적 특성을 분석하였다. 무전해도금 구리박막의 접착특성은 스크래치 테스트에 의해 평가하였으며, 열적 증착방법과 스퍼터 방법으로 증착된 구리 박막과 비교하였다. 스크래치 테스트 결과, 무전해도금 구리 박막의 접착력이 열적 증착과 스퍼터 방법으로 증착된 구리 박막보다 더 우수하였다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1994년도 추계 학술발표 강연 및 논문 개요집
• /
• pp.43-44
• /
• 1994

• 마이크로전자및패키징학회지
• /
• 제6권1호
• /
• pp.31-37
• /
• 1999

본 연구에서는 집적회로의 배선공정에 적용될 무전해도금된 Cu박막의 열적 특성과 접착특성에 대하여 고찰하였다. 시편은 Si 기판에 MOCVD법으로 TaN 확산방지막을 증착시킨 후 그 위에 무전해도금법으로 Cu 막을 증착시켜 Cu/TaN/Si 구조의 다층박막을 제조하였다. 이렇게 제조된 Cu/TaN/Si 시편을 수소와 Ar 분위기에서 각각 열처리시킨 후 열처리온도에 따른 비저항을 측정함으로써 Cu박막의 열적 안정성을 분석하였다. Cu박막과 TaN확산방지막과의 접착특성을 분석하기 위하여 scratch test를 사용하였으며, TaN 확산방지막에 대한 무전해도금된 Cu배선막의 접착력은 일반적인 Thermal evaporation과 Sputturing 방법으로 증착된 Cu 박막의 경우와 비교함으로써 평가되었다. TaN 박막에 대한 Cu박막의 접착성을 평가하기 위해 scratch test를 행한 결과 무전해도금된 Cu박막의 경우 다른 방법으로 증착된 Cu 박막과 비슷한 접착특성을 나타내었으며, acoustic emission분석과 microscope 관찰 결과 sputtering이나 evaporation 방법으로 증착된 Cu박막 보다 무전해도금된 Cu박막이 상대 적으로 우수한 접착력을 나타내었다.

• Journal of Electrochemical Science and Technology
• /
• 제8권3호
• /
• pp.215-221
• /
• 2017

The electroless plating process largely consists of substrate cleaning, seed formation (activator formation), and electroless plating. The most widely used activator in the seed formation step is Pd, and Sn ions are used to facilitate the formation of this Pd seed layer. This is problematic because the Sn ions interfere with the reduction of Cu ions during electroless plating; thus, the Sn ions must be removed by a hydrochloric acid cleaning process. This method is also expensive due to the use of Pd. In this study, Cu electroless plating was performed by forming a seed layer using a silver nanosol instead of Pd and Sn. The effects of the Ag nanosol concentration in the pretreatment solution and the pretreatment time on the thickness and surface morphology of the Cu layer were investigated. The degrees of adhesion to the substrate were similar for the electroless-plated Cu layers formed by conventional Pd activation and those formed by the Ag nanosol.

• 한국재료학회지
• /
• 제13권2호
• /
• pp.101-105
• /
• 2003

In this study, we have investigated the availability of the electroless Ni-B plating for a diffusion barrier of the bus electrode. The Ni-B layer of 1$\beta$: thick was electroless deposited on the electroplated Cu bus electrode for AC plasma display. The layer was to encapsulate Cu bus electrode to prevent from its oxidation and to serve as a diffusion barrier against Cu contamination of the transparent dielectric layer in AC plasma display. The microstructure of the as-plated barrier layer was made of an amorphous phase and the structure was converted to crystalline at about 30$0^{\circ}C$. The concentration of boron was about 5∼6 wt.% in the electroless Ni-B deposit regardless of DMAB concentration. The electroless Ni-B deposit was coated on the surface of the electroplated Cu bus electrode uniformly. And the electroless Ni-B plating was found to be an appropriate process to form the diffusion barrier.