• Journal of the Korean Chemical Society
• /
• v.33 no.5
• /
• pp.496-503
• /
• 1989

The chemical behavior of trivalent lanthanide (Pr(III) and Yb(III)) and 2, 2, 6, 6-tetramethyl-3, 5-heptanedione(dipivaloylmethane) complexes was investigated by the use of direct current, differential pulse polarography and cyclic voltammetry. In this study, it was founded that the reduction of trivalent lanthanide complexes was observed by one electron transfer process at Epc = -0. 13 V and -0.80 V of Pr(III), and -0.02 V of Yb(III) vs. Ag-AgCl electrode. Also, it was founded that the treatment of DP and CV to the case of a first-order chemical equilibrium reaction preceding a reversible and irreversible one electron transfer reaction, (a >0. 5) the socalled ErCr electrode process. The equilibrium constant (lnK) obtained, of various solvents, these constant were founded to be increases with decreasing dielectric constant of the solvents. Plots of lnK for these reaction against ln(l/D) for the solvents was fairly straight lines, and the behavior of the heavier lanthanides was decreased equilibrium constant with increasing atomic number.

• Journal of the Korean Ceramic Society
• /
• v.43 no.5 s.288
• /
• pp.270-276
• /
• 2006

LSGM(($La_xSr_{1-x})(Ga_yMg_{1-y})O_3$) electrolyte is known to show very serious interfacial reaction with other unit cell components, especially with an anode. Such an interfacial reaction induced the phase instability of constituent component and deterioration of the unit cell performance, which become the most challenging issues in LSGM-based SOFCs. In this study, we fabricated LSGM($La_{0.8}Sr_{0.2}Ga_{0.83}Mg_{0.17}O_x$) electrolyte supported-type cell in order to avoid such interfacial problem by lowering the heat-treatment temperature of the electrode fabrication. According to the microstructural and phase analysis, there was no serious interfacial reaction at both electrolyte/anode and electrolyte/cathode interfaces. Moreover, from the electrochemical characterization of the unit cell performance, there was no distinct deterioration of the open cell voltage as well as an internal cell resistance. These results demonstrate the most critical point to be concerned in LSGM-based SOFC is either to find a proper electrode material which will not give any interfacial reaction with LSGM electrolyte or to properly adjust the processing variables for unit cell fabrication, to reduce the interfacial reaction.

• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.499-504
• /
• 1998

For the formation of cobalt polycide gate electrode, CoSi, was grown on columnar poly-Si, granular poly-Si or amorphous Si by depositing either Co monolayer or Co/Ti bilayer and its thermal stability was compared to study effects of the substrate crystallinity and the silicide formation method. When specimens were rapidly heat-treated at 90$0^{\circ}C$ up to 600 seconds, using amorphous Si or Co/Ti on all substrates improved the thermal stability. This was attributed to the uniform chemical composition of initial CoSi, and its smooth interface with the substrates, induced by smooth and clean Si surface and delayed Co diffusion. The main factors determining the thermal stability were found to be composition uniformity and smooth interface of $CoSi_2$, intially formed at the early stage of the heat-treatment.

• Resources Recycling
• /
• v.16 no.6
• /
• pp.10-19
• /
• 2007

The mechanical process followed by hydrometallurgical treatment has been developed in order to recover cobalt and lithium from spent lithium ion battery. In the previous study, a citrate precursor combustion process to prepare cathodic active materials from the leaching solution was elucidated. Resynthesis of electrode materials should be more valuable in spent battery recycling. Conventional slurry mixing of $LiCoO_2$ and carbon cannot make uniform distribution, and therefore the cathode cannot reach the theoretical charge-discharge capacity and is easily degraded during the charge-discharge cycling. In this study, ultra-fine $LiCoO_2$ powders has been prepared by modification of the combustion process and fabricated the enhanced cathode by modification of mixing method of $LiCoO_2$ and carbon added.

• The Korean Journal of Pain
• /
• v.20 no.1
• /
• pp.60-65
• /
• 2007

Complex Regional Pain Syndromes (CRPS) type I and type II are neuropathic pain conditions that are being increasingly recognized in children and adolescents. The special distinctive features of pediatric CRPS are the milder course, the better response to treatment and the higher recurrence rate than that of adults and the lower extremity is commonly affected. We report here on a case of pediatric CRPS that was derived from ankle trauma and long term splint application at the left ankle. The final diagnoses were CRPS type I in the right upper limb, CRPS type II in the left lower limb and unclassified neuropathy in the head, neck and precordium. The results of various treatments such as medication, physical therapy and nerve blocks, including lumbar sympathetic ganglion blocks, were not effective, so implantation of a spinal cord stimulator was performed. In order to control the pain in his left lower limb, one electrode tip was located at the 7th thoracic vertebral level and two electrode tips were located at the 7th and 2nd cervical vertebral levels for pain control in right upper limb, head, neck and right precordium. After the permanent insertion of the stimulator, the patient's pain was significantly resolved and his disabilities were restored without recurrence. The patient's pain worsened irregularly, which might have been caused by psychological stress. But the patient has been treated with medicine at our pain clinic and he is being followed up by a psychiatrist. (Korean J Pain 2007; 20: 60-65)

• Resources Recycling
• /
• v.26 no.4
• /
• pp.34-41
• /
• 2017

The effect of Mn(II) concentration on the anodic reactions occurring on a Pb-Ag electrode in sulfuric acid solutions has been studied by potentiostatic oxidation in the potential range of 1.8 to 2.0 V. High oxidation potentials and low initial concentrations of Mn(II) resulted in higher concentrations of soluble Mn(III) ions which were obtained from spectrophotometric analysis of the solution after oxidation. $MnO_2$ was deposited on the electrode by electrochemical oxidation of Mn(II) at 1.8 and 1.9 V, while it was formed by disproportionation of Mn(III) at 2.0 V. No $PbO_2$ was formed in the presence of Mn(II) during potentiostatic oxidation treatment for two hours at 1.8 V. Chemical reduction of $PbO_2$ with Mn(II) led to a decrease in the amount of $PbO_2$ as Mn(II) concentration increased at 1.9 and 2.0 V.

• Fashion & Textile Research Journal
• /
• v.21 no.3
• /
• pp.363-369
• /
• 2019

This study developed electroconductive textiles by coating polypyrrole to PET nonwoven-based Polyvinyl Alcohol (PVA) nanoweb made by electrospinning and applying the developed electrotextiles as ECG Electrodes. To find the optimum coating conditions for high electrical conductivity, the ratios of 2.6-Naphthalenedisulfonic acid with Disodium Salt (NDS) vs Ammonium Persulfate (APS) as an oxidant and a doping agent in the solution were changed from 3:7 to 7:3; the immersion time of the specimen in the solution was 1 hour. PVA nanowebs coated with polypyrrole under various conditions were filmed with FE-SEM. FT-IR analysis was also performed to examine the presence of polypyrrole nanoparticles in the PVA nanoweb. The electrical resistance of the treated specimens were measured with a Multimeter. Consequently, the PVA Nano Web was undamaged even after heat treatment that allowed for coating. Uniform polypyrrole nanoparticles then formed on the surface of the PVA nanoweb after coating. The measured electrical resistance was shown to be at least $12K{\Omega}/{\Box }$ from a maximum of $3,456K{\Omega}/{\Box }$. The proper amount of NDS content had a positive effect on the conductivity improvement of electroconductive textiles; in addition, the highest electrical conductivity was achieved with a ratio of 3:7 between NDS and APS.

• Korean Journal of Materials Research
• /
• v.29 no.3
• /
• pp.167-174
• /
• 2019

To improve the performance of carbon nanofibers as electrode material in electrical double-layer capacitors (EDLCs), we prepare three types of samples with different pore control by electrospinning. The speciments display different surface structures, melting behavior, and electrochemical performance according to the process. Carbon nanofibers with two complex treatment processes show improved performance over the other samples. The mesoporous carbon nanofibers (sample C), which have the optimal conditions, have a high sepecific surface area of $696m^2g^{-1}$, a high average pore diameter of 6.28 nm, and a high mesopore volume ratio of 87.1%. In addition, the electrochemical properties have a high specific capacitance of $110.1F\;g^{-1}$ at a current density of $0.1A\;g^{-1}$ and an excellent cycling stability of 84.8% after 3,000 cycles at a current density of $0.1A\;g^{-1}$. Thus, we explain the improved electrochemical performance by the higher reaction area due to an increased surface area and a faster diffusion path due to the increased volume fraction of the mesopores. Consequently, the mesoporous carbon nanofibers are demonstrated to be a very promising material for use as electrode materials of high-performance EDLCs.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.2
• /
• pp.93-100
• /
• 2021

Copper sheets has been used widely in electric and electron industry fields because they have good electric and heat conduction property of the material. And, in order to bond copper material, a kind of soldering process is generally used. But, because it is difficult to bond by soldering between overlapped thin copper sheets, so, another kind of brazing bonding process can be used in that case. But, because the brazing process needs wide bonding area, it needs heat treatment process in electric furnace. Generally, for spot welding of sheets, a conventional electric Resistance Spot Welding process(RSW) has been used, it has welding characteristics using contact resistance heating induced by electric current flow between sheets. But, because copper sheets has the low electric resistance, it is difficult to weld by electric resistance spot welding. So, in this study, an electric Resistance heated Surface Friction Spot Welding process(RSFSW) is suggested and is testified for the spot welding ability of thin copper sheets. It is known from the experimental results and simulation that the suggested spot welding process will be able to improve the spot welding ability of copper sheets by the combined three kinds of heating generated by surface friction by rotating pin, and conducted from heated steel electrode, and generated by contact resistance of electricity.

• International Journal of Computer Science & Network Security
• /
• v.23 no.2
• /
• pp.183-192
• /
• 2023

Radiofrequency ablation (RFA) is an alternative treatment for liver cancer to the surgical intervention preferred by surgeons. However, the main challenge remains the use of RF for the ablation of large tumours (i.e., tumours with a diameter of >3 cm). For large tumours, RFA takes a large duration in the ablation process compared with surgery, which increases patient pain. Therefore, RFA for large tumours is not preferred by surgeons. The currently materials used in RF electrodes, such as the nickeltitanium alloy (nitinol), are characterized by low thermal and electrical conductivities. On the other hand, the use of materials that have high thermal and electrical conductivities, such as titanium aluminide alloy (gamma titanium), produces more thermal energy for tumours. In this paper, we developed a cool-tip RF electrode model that uses nickel-titanium alloy and replaced it with titanium aluminide alloy by using the finite element model (FEM). The aim of this paper is to study the effect of the thermal and electrical conductivities of gamma titanium on the ablation volume. Results showed that the proposed design of the electrode increased the ablation rate by 1 cm³ /minute and 6.3 cm³/10 minutes, with a decrease in the required time ablation. Finally, the proposed model reduces the ablation time and damages healthy tissue while increasing the ablation volume from 22.5% cm³ to 62.5% cm³ in ten minutes compared to recent studies.