• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 춘계학술대회 논문집
• /
• pp.18-18
• /
• 2010

최근 PCA 아크튜브를 사용한 세라믹 메탈핼라이드 램프가 개발되어 기존의 석영관 메탈핼라이드 램프의 사용 범위를 넘어 다양하게 활용되고 있다. 이에 따라 램프의 신뢰성 또한 중요한 요소로 여겨지게 됨으로 본 논문에서는 세라믹 메달핼라이드 램프의 아크튜브의 열화특성을 확인하기기 위해 램프를 가속열화 시켜 구조적 변화를 확인하였다. 이 결과 모세 관 내 Moly winding과 세라믹 아크튜브의 열팽창계수 차이로 인해 간격이 멀어지고 그 사이로 원소들이 침입하였고 이로 인해 아크튜브와 전극의 열화를 촉진하며 전극의 틀어짐을 유발하였다. 또 내부에 봉입된 희토류 금속 요오드화물이 고온에서 PCA 관벽과 반응을 일으켜 아크튜브를 부식시킴을 확인할 수 있었다.

• ETRI Journal
• /
• 제20권2호
• /
• pp.241-249
• /
• 1998

The structure and electrical characteristics of metal-ferroelectric-semiconductor FET(MFSFET) for a single transistor memory are presented. The MFSFET was comprised of polysilicon islands as source/drain electrodes and $BaMgF_4$ film as a gate dielectric. The polysilicon source and drain were built-up prior to the formation of the ferroelectric film to suppress a degradation of the film due to high thermal cycles. From the MFS capacitor, the remnant polarization and coercive field were measured to be about $0.6{\mu}C/cm^2$ and 100 kV/cm, respectively. The fabricated MFSFETs also showed good hysteretic I-V curves, while the current levels disperse probably due to film cracking or bad adhesion between the film and the Al electrode.

• Transactions on Electrical and Electronic Materials
• /
• 제6권1호
• /
• pp.6-9
• /
• 2005

Aging characteristics of 0.2PMN-0.8PZT multilayer ceramic actuators (MCA) has been investigated by applying both triangular wave function for unpoled and unipolar wave for poling. P-E hysteresis loops of the MCA had been distorted after about 90 million cycles running in triangular wave function. Effective electromechanical coupling coefficient was calculated in resonant and anti resonant frequencies. And pseudo-piezoelectric constant $d_{33}$ was also estimated from the strain versus electric field characteristics. The crack growth of MCA was clearly observed along to the boundary between electrode and inactive area. That results were thought due to the internal tensile stress came from both actuation of $d_{33}$ mode and motion of Poisson ratio.

• 한국표면공학회지
• /
• 제36권2호
• /
• pp.168-175
• /
• 2003

The purpose of solder plating on chip external electrode is to provide a proper solderability to chips on PCB's. The quantitative or qualitative analysis of solderability has been performed by destructive methods, reflow or flow. Evidently, the solderability tends to depend on the grain structure which is varied with additives. Research on the feasibility of employing electrochemical techniques to characterize the solderability of electroplated tin - lead, with respect to the additives, was non destructively performed. The deposit morphology and the polarization behavior of electrolytes containing proprietary additives were evaluated to investigate the soldering degradation. The plated panels from synthetic electrolyte were analyzed according to % Sn, plating thickness, deposit appearance, grain structure, solderability and cyclic voltammetry.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.2047-2049
• /
• 2000

In this study, we describe comparison of insulation characteristics of polyamid papers with heating conditions. The partial discharge behavior until breakdown and breakdown strength for thermal degradation films are observed in $SF_6$ gas chamber. The four layered NOMEX films of thickness of 50${\mu}m$ were used as solid insulation films and the sphere of which diameter is 40mm to sphere electrode system was used and each insulation films were inserted between sphere electrodes. The used gas pressure was 1.0bar and used temperature was each of 250$^{\circ}C$, 270$^{\circ}C$, 300$^{\circ}C$, 320$^{\circ}C$, 350$^{\circ}C$ and the voltage were applied until breakdown films.

• 한국세라믹학회지
• /
• 제53권5호
• /
• pp.469-477
• /
• 2016

The application of nanomaterials for electrodes of intermediate temperature solid oxide fuel cells (SOFC) is introduced. In conventional SOFCs, the operating temperature is higher than 1073 K, and so application of nanomaterials is not suitable because of the high degradation rate that results from sintering, aggregation, or reactions. However, by allowing a decrease of the operating temperature, nanomaterials are attracting much interest. In this review, nanocomposite films with columnar morphology, called double columnar or vertically aligned nanocomposites and prepared by pulsed laser ablation method, are introduced. For anodes, metal nano particles prepared by exsolution from perovskite lattice are also applied. By using dissolution and exsolution into and from the perovskite matrix, performed by changing $P_{O2}$ in the gas phase at each interval, recovery of the power density can be achieved by keeping the metal particle size small. Therefore, it is expected that the application of nanomaterials will become more popular in future SOFC development.

• Journal of Electrical Engineering and Technology
• /
• 제9권2호
• /
• pp.609-614
• /
• 2014

We fabricated amorphous zinc tin oxide (ZTO) transparent thin-film transistors (TTFTs). The effects of Al electrode on the mobility and threshold voltage of the ZTO TTFTs were investigated. It was found that the aluminum (Al)-ZTO contact decreased the mobility and increased the threshold voltage. Traps, originating from $AlO_x$, were assumed to be the cause of degradation. An indium tin oxide film was inserted between Al and ZTO as a buffer layer, forming an ohmic contact, which was revealed to improve the performance of ZTO TTFTs.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.348-348
• /
• 2005

High capacitance MLCC has been enabled through the use of nickel electrodes to produce thinner layers at acceptable costs. High capacitance MLCC devices offer significant advantages to electrolytics such as tantalum and aluminum ; Lower ESR for high frequency applications. Non-polarized. Many process improvement have enabled this technology Higher dielectric constants Thinner dielectric and electrode layers through BME More accurate layer construction. This study is high capacitance MLCC electrical propertics. reliability, Analysis on DOE(Design Of Experiment) of the electical propertics.

• 한국표면공학회지
• /
• 제30권2호
• /
• pp.121-127
• /
• 1997

Vanadium tungsten oxide thin films were formed by RF magnetron sputtering and the effects of tungsten addition on the crystallinity and on the electrochemical behavior were investigated. X-ray analysis revealed that amorphized films could be obtained by tungase addition. In order to investigate the electrochemical behavior of the vanadium tungsten oxide films, electrochemical insertion and extraction of lithium were out in 1m $LiCIO_4$-PC-DME electrolyte using litium metal as a counter electrode. When the tungsten was added to the $V_2O_5$ films, cycling reversibility was considerably improved. Electrochemical test showed the cell capacity of about $70\mu\;Ah/\textrm{cm}^2-\mu\textrm{m}$ when the amount of additive tungseten reached 30 atomic percent. No appreciable degradation of the cell capacity could be observed after hundred cycles of insertion and extration od Li.

• Journal of Electrochemical Science and Technology
• /
• 제14권2호
• /
• pp.145-151
• /
• 2023

Planer-type electrolyte substrates are often utilized for stack manufacturing of electrolyte-supported solid oxide fuel cells (ES-SOFCs) to fulfill necessary requirements such as a high mechanical strength and redox stability. This work did an electrochemical analysis of ES-SOFC with different NiO-YSZ anode thicknesses to find the optimal value for the high performance of the fuel cell. The cell resistivities were constant at anode thickness between 25-58 ㎛, but a thick anode (74 ㎛) caused a high electrode resistivity leading to a dramatic reduction in cell performance. A stability test was performed for 50 hours at 700℃, and the results showed a degradation rate of 0.3% per 1000 h by extrapolated fitting.