• Corrosion Science and Technology
• /
• v.19 no.6
• /
• pp.288-295
• /
• 2020

This study investigated the erosion-corrosion characteristics of 5038-H321 aluminum alloy in a natural seawater solution through various electrochemical experiments and flow rate parameters. Cathodic polarization experiments were conducted at flow rates ranging from 4 to 12 knots. Considering the concentration polarization section representing a relatively low current density, the range of the potentiostatic experiment was determined to be -1.6 to -1.0 V. The potentiostatic experiment was conducted at various potentials for 180 minutes in seawater. After the experiment, the corrosion characteristics were evaluated by observing surface morphology and measuring surface roughness. As a result, as the applied potential was lower, the amount of calcareous deposits increased and the roughness tended to increase. On the other hand, it was confirmed that the roughness was larger in the static condition than the flow rate condition due to the influence of the flow velocity. Variations in the chemical composition with flow rate variations were analyzed by energy-dispersive spectroscopy (EDS). In conclusion, the cathodic potential of AA5083-H321 in seawater was determined to be -1.0 V.

• Corrosion Science and Technology
• /
• v.21 no.5
• /
• pp.360-371
• /
• 2022

Electropolishing has various parameters because an electrochemical reaction is applied. Accordingly, experiments to determine factors and levels of electropolishing conditions are in progress for various materials. The purpose of this investigation was to optimize conditions for electropolishing using the taguchi method for UNS S31603. Factors such as electrolyte composition ratio, electrolyte temperature, and electropolishing process time were selected. Electropolishing was optimized using analysis of variance (ANOVA), signal-to-noise ratio (the smaller the better characteristics), and surface analysis. Results of ANOVA revealed that only the electrolyte composition ratio among factors was effective for surface roughness. As a result of statistical analysis of the signal-to-noise ratio, the highest signal-to-noise ratio was calculated under electropolishing conditions with sulfuric acid and phosphoric acid ratio of 4:6, an electrolyte temperature of 75 ℃, and electropolishing process time of 7 minutes. In addition, the surface roughness after electropolishing under the above conditions was 0.121 ㎛, which was improved by more than 88% compared to mechanical polishing.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.5
• /
• pp.507-514
• /
• 2022

There is growing interest in sustainable energy sources that can reduce fossil fuel dependence and environmental pollution while meeting rapidly growing energy demands. Hydrogen have been investigated as one of the ideal alternative energies because it has relatively high efficiency without emitting pollutants. The light-sensitized enzymatic (LSE) system, which uses hydrogenase-enzymes, is one of the methods towards economically feasible system configurations that enhance the rate of hydrogen generation. Hydrogenase is an enzyme that catalyzes a reversible reaction that oxidizes molecular hydrogen or produces molecular hydrogen from protons and electrons. In this paper, utilization of [NiFe]-hydrogenase (from Pyrococcus furiosus) in photoelectrochemical hydrogen production system such as handling, immobilization, physicochemical and electrochemical analysis, process parameters, etc. was introduced.

• Nuclear Engineering and Technology
• /
• v.55 no.4
• /
• pp.1518-1527
• /
• 2023

A method was proposed for in-situ evaluating the thickness and resistivity of the oxide/hydroxide film formed on the surface of aluminum alloy exposed to sump water formed in the containment after a loss-of-coolant accident. The evaluation entailed fitting a model for the film impedance, which has film thickness and other variables describing the resistivity profile of the film along its thickness direction as fitting parameters, to the practically measured electrochemical impedance data. The obtained resistivity profiles implied that the films formed at pHs_25℃ 7, 8, 9, 10, and 11 all had a duplex structure; compared to the outer layer in contact with the solution, the inner layer of the film had a much higher resistivity and was inferred to be denser and provide most of the protectiveness of the film. Both the thickness and the total resistance of the film decreased with the increasing solution pH_25℃, suggesting that the films formed in more alkaline solutions had less protectiveness against corrosion, consistent with the increasing aluminum alloy corrosion rates previously identified.

• Journal of Sensor Science and Technology
• /
• v.32 no.6
• /
• pp.357-369
• /
• 2023

Wound healing is a complex and dynamic process, making the accurate and timely assessment of skin wounds a crucial aspect of effective wound care management, especially for chronic wounds. Unlike conventional wound dressings that simply cover the wound area once some form of medicine is administered onto the wound, recent studies have introduced versatile approaches to smart wound dressings capable of interacting with wound fluids to monitor physicochemical and pathological parameters to determine the wound healing status. Such electrochemical wound dressings can be integrated with on-demand, closed-loop drug delivery or stimulation systems and ultimately expanded into an ideal technological platform for the prevention, treatment, and management of skin wounds or illnesses. This article briefly reviews the wound healing mechanism and recent strategies for effective wound care management. Specifically, this review discusses the following aspects of smart wound dressings: sensor-integrated smart bandages to detect wound biomarkers, smart bandages developed to accelerate wound healing, and wireless, closed-loop automatic (on-demand) wound healing systems. This review concludes by providing future perspectives on effective wound care management.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.6
• /
• pp.651-662
• /
• 2022

The electrochemical impedance spectroscopy(EIS) method was used to evaluate the concrete deterioration process related to chloride-induced steel corrosion with various corrosion levels(initiation, rust propagation and acceleration periods). The impressed current technique, with four total current levels of 0C, 13C, 65C and 130C, was used to accelerate steel corrosion in concrete cylinder samples with w/c ratio of 0.4, 0.5, and 0.6, immersed in a 0.5M NaCl solution. A series of EIS measurements was performed to monitor concrete deterioration during the accelerated corrosion test in this study. Some critical parameters of the equivalent circuit were obtained through the EIS analysis. It was observed that the charge transfer resistance(R_c) dropped sharply as the impressed current increased from 0C to 13C, indicating a value of approximately 10kΩcm². However, the sensitivity of R_c significantly decreased when the impressed current was further increased from 13C to 130C after corrosion of steel had been initiated. Meanwhile, the double-layer capacitance value(C_dl) linearly increased from 50×10^-6μF/cm² to 250×10^-6μF/cm² as the impressed current in creased from 0C to 130C. The results in this study showed that monitoring C_dl is an effective measurement parameter for evaluating the progress of internal concrete damages(de-bonding between steel and concrete, micro-cracks, and surface-breaking cracks) induced by steel corrosion. The findings of this study provide a fundamental basis for developing an embedded sensor and signal interpretation method for monitoring concrete deterioration due to steel corrosion at various corrosion levels.

• Korean Journal of Clinical Pharmacy
• /
• v.10 no.1
• /
• pp.13-18
• /
• 2000

The bioequivalence of two clarithromycin tablets, the $Klaricid^{TM}$ (Ciba-Geigy Korea Ltd.) and the $Pylocin^{TM}$ (Kyungdong Pharmaceutical Co., Ltd.), was evaluated according to the Korean Guidelines for Bioequivalence Test (KGBT 1998). Sixteen healthy male volunteers ($20\sim26$ years old) were randomly divided into two groups and a randomized $2\times2$ cross-over study was employed. After one tablet containing 250 mg of clarithromycin was orally administered, blood sample was taken at predetermined time intervals, and the concentrations of clarithromycin in serum were determined using high-performance liquid chromatographic method with electrochemical detector. The pharmaco-kinetic parameters (area under the concentration-time curve: $AUC_t$, maximum concentration; $C_{max}$ and time to maximum concentration; $T_{max}$) were calculated and analysis of variance (ANOVA) was utilized for the statistical analysis of parameters. The results showed that the differences in $AUC_t,\;C_{max}\;and\;T_{max}$ between two tablets based on $Klaricid^{TM}$ tablet were $-0.22\%,\;-0.48\%\;and\;-1.63\%$, respectively. The powers $(1-\beta)\;for\;AUC_t,\;C_{max}\;and\;T_{max}\;were\;99.07\%,\;88.15\%\;and\;99.99\%$, respectively. Detectable differences $(\Delta)\;and\;90\%$ confidence intervals ($\alpha$=0.10) were all less than $\pm20\%$ All the parameters above met the criteria of KGBT 1998, indicating that $Pylocin^{TM}$ tablet is bioequivalent to $Klaricid^{TM}$ tablet.

• Journal of the Korean Electrochemical Society
• /
• v.4 no.4
• /
• pp.146-151
• /
• 2001

The Frumkin adsorption isotherm of the over-potentially deposited hydrogen (OPD H) for the cathodic $H_2$ evolution reaction (HER) at the poly-Ni|0.05M KOH aqueous electrolyte interface has been studied using the phase-shift method. The behavior of the phase shift $(0^{\circ}\leq{\phi}\leq90^{\circ})$ for the optimum intermediate frequency corresponds well to that of the fractional surface coverage $(1\geq{\theta}\geq0)$ at the interface. The phase-shift method, i.e., the Phase-shift profile $(-{\phi}\;vs.\;E)$ for the optimum intermediate frequency, can be used as a new method to estimate the Frumkin adsorption isotherm $(\theta\;vs.\;E)$ of the OPD H for the cathodic HER at the interface. At the poly-Ni|0.05M KOH aqueous electrolyte interface, the rate (r) of change of the standard free energy of the OPD H with $\theta$, the interaction parameter (g) for the Frumkin adsorption isotherm, the equilibrium constant (K) for the OPD H with $\theta$, and the standard free energy $({\Delta}G_{\theta})$ of the OPD H with ${\theta}$ are $24.8kJ mol^{-1},\;10,\;5.9\times10^{-6}{\leq}K{\leq}0.13,\;and\;5.1\leq{\Delta}G_{\theta}\leq29.8kJ\;mol^{-1}$. The electrode kinetic parameters $(r,\;g,\;K,\;{\Delta}G_{\theta})$ depend strongly on ${\theta} (0{\leq}{\theta}{\leq}1)$.

• Nuclear Engineering and Technology
• /
• v.24 no.2
• /
• pp.154-162
• /
• 1992

Two major goals for chemical cleaning on the secondary side of nuclear steam generators are to remove sludge effectively and to minimize corrosion of base metals. In this work, electrochemical and sludge dissolution behaviors have been investigated in order to find out which parameters are critical and important during a copper removal process for chemical cleaning and to evaluate safety aspects and effectiveness of two major copper removal processes developed commercially in foreign countries. Hydrogen peroxide is vert effective for the process to use EDTA, NH$_4$OH and EDA at 38$^{\circ}C$ to control the potential of copper in a potential range sood for copper sludge removal. Corrosion rates for carbon steel SA 285 Gr.C and Alloy 600 are very small during this process if it is controlled properly. However, the corrosion rate of SA 285 Gr.C will be increased greatly if its corrosion potential is maintained below -450mV. The process to use EDA and ammonium carbonate is effective at 6$0^{\circ}C$ to dissolve copper sludge if the corrosion potential of copper can be controlled above -200mV. However, it is very difficult to raise the corrosion potential of copper to this range by air blowing and stirring.

• Journal of the Korean Ceramic Society
• /
• v.40 no.6
• /
• pp.507-512
• /
• 2003

The LiN $i_{l-y}$ $Co_{y}$ $O_2$ samples were synthesized at 80$0^{\circ}C$ and 85$0^{\circ}C$, by the solid-state reaction method, from the various starting materials LiOH, L $i_2$C $O_3$, NiO, NiC $O_3$, $Co_3$ $O_4$, CoC $O_3$, and their electrochemical properties are investigated. The LiN $i_{l-y}$ $Co_{y}$ $O_2$ pre-pared from L $i_2$C $O_3$, NiO, and $Co_3$ $O_4$ exhibited the $\alpha$-NaFe $O_2$ structure of the rhombohedral system (space group; R3m). As the Co content increased, the lattice parameters a and c decreased. The reason is that the radius of Co ion is smaller than that of Ni ion. The increase in da shows that two-dimensional structure develops better as the Co content increases. The LiN $i_{0.7}$ $Co_{03}$. $O_2$［HOO(800,0.3)] synthesized at 80$0^{\circ}C$from LiOH, NiO, and $Co_3$ $O_4$ exhibited the largest first discharge capacity 162 mAh/g. The size of particles increases roughly as the valve of y increases. The samples with the larger particles have the larger first discharge capacities. The cycling performances of the samples with the first discharge capacity larger than 150 mAh/g were investigated. The LiN $i_{0.9}$ $Co_{0.1}$ $O_2$［COO(850,0.1)］ synthesized at 85$0^{\circ}C$ from L $i_2$C $O_3$, NiO, and $Co_3$ $O_4$ showed an excellent cycling performance. The sample with the larger first discharge capacity will be under the more severe lattice destruction, due to the expansion and contraction of the lattice during intercalation and deintercalation, than the sample with the smaller first discharge capacity. As the first discharge capacity increases, the capacity fading rate thus increases.increases.s.s.s.