• Environmental Engineering Research
• /
• v.15 no.2
• /
• pp.71-78
• /
• 2010

To understand the effects of acclimation schemes on the formation of anode biofilms, different electrical performances are characterized in this study, with the roles of suspended and attached bacteria in single-chamber microbial fuel cells (MFCs). The results show that the generation of current in single-chamber MFCs is significantly affected by the development of a biofilm matrix on the anode surface containing abundant immobilized microorganisms. The long-term operation with suspended microorganisms was demonstrated to form a dense biofilm matrix that was able to reduce the activation loss in MFCs. Also, a Pt-coated anode was not favorable for the initial or long-term bacterial attachment due to its high hydrophobicity (contact angle = $124^{\circ}$), which promotes easy detachment of the biofilm from the anode surface. Maximum power ($655.0\;mW/m^2$) was obtained at a current density of $3,358.8\;mA/m^2$ in the MFCs with longer acclimation periods. It was found that a dense biofilm was able to enhance the charge transfer rates due to the complex development of a biofilm matrix anchoring the electrochemically active microorganisms together on the anode surface. Among the major components of the extracellular polymeric substance, carbohydrates ($85.7\;mg/m^2_{anode}$) and proteins ($81.0\;mg/m^2_{anode}$) in the dense anode biofilm accounted for 17 and 19%, respectively, which are greater than those in the sparse anode biofilm.

• Korean Chemical Engineering Research
• /
• v.48 no.3
• /
• pp.311-315
• /
• 2010

The effects of $SO_2$ on the performance of proton exchange membrane(PEMFC) were investigated by introduction air containing $SO_2$ into cathode inlet of PEMFC. And the recovery of the cell performance by applying clean air, cycle voltammetry(CV) and high voltage holding following exposure contaminated air was studied. The $SO_2$ concentration range used in the experiments was from 20 ppb to 1.3 ppm. The performance degradation and recovery were measured by constant-current discharging, I-V polarization and electrochemical impedance spectroscopy(EIS). The cell voltage gradually decayed with time and decreased by 17 mV after 200 hours of 20 ppb $SO_2$ injection. The cell performance can be recovered partially by clean air flushing, CV and high voltage holding due to desorption of S from Pt catalyst.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.33.2-33.2
• /
• 2011

CMP (Chemical-Mechanical Planarization) 공정이란 화학적 반응과 기계적 힘을 동시에 이용하여 표면을 평탄화하는 공정으로, 반도체 산업에서 회로의 고집적화와 다층구조를 형성하기 위해 CMP 공정이 도입되었으며 반도체 패턴의 미세화와 다층화에 따라 CMP 공정의 중요성은 더욱 강조되고 있다. CMP 공정은 압력, 속도 등의 공정조건과, 화학적 반응을 유도하는 슬러리, 기계적 힘을 위한 패드 등에 의해 복합적으로 영향을 받는다. CMP 공정에서, 폴리우레탄 패드는 많은 기공들을 포함한 그루브(groove)를 형성하고 있어 웨이퍼와 직접적으로 접촉을 하며 공정 중 유입된 슬러리가 효과적으로 연마를 할 수 있도록 도와주는 역할을 한다. 하지만, 공정이 진행 될수록 그루브는 손상이 되어 제 역할을 하지 못하게 된다. 패드 컨디셔닝이란 컨디셔너가 CMP 공정 중에 지속적으로 패드 표면을 연마하여 패드의 손상된 부분을 제거하고 새로운 표면을 노출시켜 패드의 상태를 일정하게 유지시키는 것을 말한다. 한편, 금속박막의 CMP 공정에 사용되는 슬러리는 금속박막과 산화반응을 하기 위하여 산화제를 포함하는데, 산화제는 금속 컨디셔너 표면을 산화시켜 부식을 야기한다. 컨디셔너의 표면부식은 반도체 수율에 직접적인 영향을 줄 수 있는 scratch 등을 발생시킬 뿐만 아니라, 컨디셔너의 수명도 저하시키게 되므로 이를 방지하기 위한 노력이 매우 중요하다. 본 연구에서는 컨디셔너 표면에 연마 잔여물 흡착을 억제하고, 슬러리와 컨디셔너 표면 간에 일어나는 표면부식을 방지하기 위하여 소수성 자기조립 단분자막(SAM: Self-assembled monolayer)을 증착하여 특성을 평가하였다. SAM은 2가지 전구체(FOTS, Dodecanethiol를 사용하여 Vapor SAM 방법으로 증착하였고, 접촉각 측정을 통하여 단분자막의 증착 여부를 평가하였다. 또한 표면부식 특성은 Potentiodynamic polarization와 Electrochemical Impedance Spectroscopy (EIS) 등의 전기화학 분석법을 사용하여 평가되었다. SAM 표면은 정접촉각 측정기(Phoenix 300, SEO)를 사용하여 $90^{\circ}$ 이상의 소수성 접촉각으로써 증착여부를 확인하였다. 또한, 표면에너지 감소로 인하여 슬러리 내의 연마입자 및 연마잔여물 흡착이 감소하는 것을 확인 하였다. Potentiodynamic polarization과 EIS의 결과 분석으로부터 SAM이 증착된 표면의 부식전위와 부식전류밀도가 감소하며, 임피던스 값이 증가하는 것을 확인하였다. 본 연구에서는 컨디셔너 표면에 SAM을 증착 하였고, CMP 공정 중 발생하는 오염물의 흡착을 감소시킴으로써 CMP 연마 효율을 증가하는 동시에 컨디셔너 금속표면의 부식을 방지함으로써 내구성이 증가될 수 있음을 확인 하였다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.1
• /
• pp.217-222
• /
• 2018

The deterioration of the Battery is decided by SoC and SoH. To determine Battery deterioration, SoC measurement method of Battery by Transfer Function was studied. The SoC of the Battery changes most greatly in the 1Hz band where the DC resistance is detected. but it is a narrow band to observe, therefore, the observation band was moved to 1kHz using the tone busrst signal. Welch's method was used to observe the frequency domain characteristics of the signal. As a result of the spectral estimation, it was confirmed that the response signal of the battery is 1dB difference when the SoC is 40%, 60%, and 80%, respectively. Through this, Proposed the new method of Battery SoC measurement.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.1
• /
• pp.41-45
• /
• 2007

Phospho-olivine $LiFePO_4$ cathode materials were prepared by hydrothermal reaction. Carbon black was added to enhance the electrical conductivity of $LiFePO_4$. The structural and morphological performance of $LiFePO_4$ and $LiFePO_4$-C powders were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM). $LiFePO_4$/Li and $LiFePO_4$-C/Li cells were characterized electrochemically by cyclic voltammogram (CV), charge/discharge experiments and ac impedance spectroscopy. The results showed that the discharge capacity of $LiFePO_4$/Li cell was 147 mAh/g at the first cycle and 118 mAh/g after 30 cycles, respectively. The discharge capacity of $LiFePO_4$-C/Li cell with 5 wt% carbon black was the largest among $LiFePO_4$-C/Li cells, 133 mAh/g at the first cycle and 128 mAh/g after 30 cycles, respectively. It was demonstrated that cycling performance of $LiFePO_4$-C/Li cell with 5 wt% carbon black was better than that of $LiFePO_4$/Li cell.

• Applied Chemistry for Engineering
• /
• v.24 no.3
• /
• pp.247-252
• /
• 2013

Sulfonated poly(ether ether ketone) (SPEEK) with a certain degree of sulfonation were synthesized by reacting PEEK and sulfuric acid at different reaction time. Then ion-selective composite carbon electrodes (ISCCE) were fabricated by coating the prepared SPEEK on the surface of carbon electrodes. The specific capacitance and resistance of the ISCCE were analyzed by electrical impedance spectroscopy. The ion exchange capacities (IEC) of the SPEEKs were measured in the range of 1.60~2.57 meq/g depending on the sulfonation time. The SPEEK more than 2.5 meq/g of IEC was considered unsuitable for fabricating the ISCCE because it was dissolved in water. The specific capacitance of the prepared ISCCE increased with increasing the IEC of coated SPEEKs and the capacitance was improved up to about 20% compared to that of uncoated carbon electrode. In addition, the electrical resistance of coating layer decreased significantly with increasing the IEC of coated SPEEKs. It is expected that the desalination efficiency of conventional capacitive deionization process can be improved by using the prepared ISCCE coated with SPEEK.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.4
• /
• pp.137-143
• /
• 2005

CrSiN coatings of stepwise changing Si concentration were deposited on stainless steel by closed field unbalanced magnetron sputtering (CFUBM) system. Microstructure of the films due to the Si concentration is measured by XRD. The corrosion behavior of CrSiN coatings in deaerated $3.5\%$ NaCl solution was investigated by potentiodynamic test, electrochemical impedance spectroscopy (EIS) and surface analyses. The microstructure of CrSiN film depends on the Si concentration. When Si/(Cr+si) was under $11.7\%$, preferred orientation is defined at CrN(220), CrN(311) and $Cr_2N(111).$ The results of potentiodynamic polarization tests showed that the corrosion current density and porosity decreased with increasing Si/(Cr+si) ratio. EIS measurements showed that the corrosion resistance of Si-bearing CrN was improved by phase transformation of the film, which leads to increase of pore resistance and charge transfer resistance. At the Si(Cr+si) ratio of 20, the Si-bearing CrN possesses the best corrosion resistance due to the highest pore resistance and charge transfer resistance.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.153-153
• /
• 2017

The application of the coating supports the mechanical characteristics of the implant, and various materials and coatings are currently being used in the implant in a way to accelerate adhesion. Especially, plasma electrolytic oxidation (PEO) coating has been proposed continually with good surface treatment of titanium alloys. Also, the PEO process can incorporate Ca and P ions on the titanium surface through variables varied factor. PEO process for bioactive surface has carried out in electrolytes containing Ca and P ions. Natural bone is composed of mineral elements such as Mg, Si, Zn, Sr, and Mn, etc. Especially, Mg and Si of these elements play role in bone formation and growth after clinical implantation of bio-implants. In this study, corrosion charateristics of PEO-treated Ti-6Al-4V alloy in solution containing Si and Mg ions has been investigated using several experimental techniques. The PEO-treated surfaces were identified by X-ray diffraction, using a diffractometer (XRD, Philips X' pert PRO, Netherlands) with Cu $K{\alpha}$ radiation. The morphology was observed by field-emission scanning electron microscopy (FE-SEM, Hitachi 4800, Japan) and energy-dispersive X-ray spectroscopy (EDX, Oxford ISIS 310, England). The potentiodynamic polarization and AC impedance tests for electrochemical degradations were carried out in 0.9% NaCl solution at similar body temperature using a potentiostat with a scan rate of 1.67mV/s and potential range from -1500mV to + 2000mV.

• Applied Chemistry for Engineering
• /
• v.4 no.2
• /
• pp.373-380
• /
• 1993

The preparation method of Raney nickel catalyst and the effect of promotor for the hydrogen electrode in alkaline fuel cell were investigated with electrochemical methods. The best electrode performance was observed with the Raney nickel which was obtained at $700^{\circ}C$ of sintering temperature and 60:40 of nickel:aluminum. As titanium was added for promotor, the activity of catalyst and characteristic of electrode was improved. Especially, the electrode containing 2w/o of titanium showed the maximum mass activity of 2.4A/g and its mean particle size was $5.7{\mu}m$. The resistance and capacitance of the electrode containing 2w/o of titanium, measured with AC impedance spectroscopy, were calculated to the $0.3{\Omega}cm^2$ and $0.42F/cm^2$, respectively.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.57.2-57.2
• /
• 2011

Dye-sensitized solar cells (DSSC) have recently been developed as a cost-effective photovoltaic system due to their low-cost materials and facile processing. The production of DSSC involves chemical and thermal processes but no vacuum is involved. Therefore, DSSC can be fabricated without using expensive equipment. The use of dyes and nanocrystalline $TiO_2$ is one of the most promising approaches to realize both high performance and low cost. The efficiency of the DSSC changes consequently in the particle size, morphology, crystallization and surface state of the $TiO_2$. Nanocrystalline $TiO_2$ materials have been widely used as a photo catalyst and an electron collector in DSSC. Front electrode in DSSC are required to have an extremely high porosity and surface area such that the dyes can be sufficiently adsorbed and be electronically interconnected, resulting in the efficient generation of photocurrent within cells. In this study, DSSC were fabricated by an screen printing for the $TiO_2$ thin film. $TiO_2$ nanoparticles characterized by X-ray diffractometer (XRD) and scanning electron microscope (SEM) and scanning auger microscopy (SAM) and zeta potential and electrochemical impedance spectroscopy(EIS).In addition, DSSC module was modeled and simulated using the SILVACO TCAD software program. Improve the efficiency of DSSC, the effect of $TiO_2$ thin film thickness and $TiO_2$ nanoparticle size was investigated by SILVACO TCAD software program.