• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.576-577
• /
• 2005

In this paper, the oxidization characteristics were analyzed according to the shapes of Residual Current Protective Device(RCD) contacts. RCD is an electrical safety device specially designed to immediately switch the electricity off when electric leakage is detected at a level harmful to a person using electrical equipment. The shapes of RCD contacts are a little bit different according to the models. When RCD is turned on, stationary and moving contact do not fit together. So, it can cause the increase of contact resistance. To discover the deterioration characteristics of RCD contacts by switching repetition, the contacts were analyzed by stereo microscope, Scanning Electron Microscope(SEM) and Energy Dispersive X-ray Spectrometer(EDS).

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.381-384
• /
• 1988

This paper analysed basic operation in Zero-voltages-switching quasi-resonant buck converter and considered steady state characteristics. Especially, it is confirmed that converter operating at maximum 1MHz switching frequency in load characteristics. In this paper, a novel slope method is proposed and implemented in regulation characteristics analysis. It is proved that experimenental results coincide with theory results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.235-238
• /
• 1996

In this paper, We intended to evaluate the characteristics of XLPE/EPDM interface which exists in the cable joint. The fault was mainly occurred in this interface. Thus we looked into the electrical characteristics through the conduction current and the breakdown test. Through from the experiment, we obtained the result that the conduction current in this interface flowed less than other dielectric materials, that the breakdown strength was higher and that the pressure dependance ㅐf the breakdown strength was higher.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.58-60
• /
• 1998

This paper analyzes the torque characteristics with the structure of harmonic side drive motor using by F.E.M and conformal mapping method. F.E.M and conformal analysis result are almost same. Through the results, we investigate how do design parameters variation affect torque characteristics.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.2
• /
• pp.104-108
• /
• 2016

To research the correlation between oxygen vacancy and the electrical characteristics of ZTO, which is made by using a target mixed ZnO:SnO₂=1:1, the ZnO, SnO₂ and ZTO were analyzed by PL, XPS, XRD patterns and electrical properties. It was compared with the electron orbital spectra of O 1s in accordance with the electrical characteristics of ZnO, SnO₂ and ZTO. The electrical characteristics of ZTO were improved by increasing the annealing temperatures, due to the high degree of crystal structures at a high temperature, and the physical properties of ZTO was similar to that of ZnO. The amorphous structure of SnO₂ was increased with increasing the temperature. The Schottky contact of oxide semiconductors was formed using the depletion region, which is increased by the electron-hole combination due to the annealing processes. ZnO showed the Ohmic contact in spite of a high annealing temperature, but SnO₂ and ZTO had Schottky contact. As such, it was confirmed that the electrical properties of ZTO are affected by the molecules of SnO₂.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.709-718
• /
• 2015

Traditional transmission planning usually caters for rated wind power output. Due to the low occurrence probability of nominal capacity of wind power and huge investment in transmission, these planning methods will leads to low utilization rates of transmission lines and poor economic efficiency. This paper provides a novel transmission expansion planning method for integrating large-scale wind power. The wind power distribution characteristics of large-scale wind power output and its impact on transmission planning are analyzed. Based on the wind power distribution characteristics, this paper proposes a flexible and economic transmission planning model which saves substantial transmission investment through spilling a small amount of peak output of wind power. A methodology based on Benders decomposition is used to solve the model. The applicability and effectiveness of the model and algorithm are verified through a numerical case.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.08a
• /
• pp.15-18
• /
• 2003

Fault current limiters (FCL) are extensively needed to suppress fault currents, especially for trunk power systems heavily connected to high voltage/large current transmission lines. Due to its ideal electrical behavior, high-temperature superconductor fault current limiter (HTSFCL) becomes one of the most important developing trends of limiters in power system. This paper describes the result of an investigation of the dielectric characteristics of turn-to-turn insulation for pancake and solenoid type reactor coil in liquid nitrogen. The influence of thickness in a variety length, on AC, DC and impulse surface flashover has been investigated. Also, the relationships between the number of turn and breakdown characteristics were clarified. The information gathered in this test series should be helpful in the design of liquid nitrogen filled DC reactor type HTSFCL.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.460_461
• /
• 2009

This paper analyzes the steady state characteristics for variable speed wind power system with doubly-fed induction generator(DFIG). This paper explains the equivalent circuit and phasor diagram of DFIG for different operating conditions. It also simulates the torque-slip characteristics with respect to changes of different parameters. Simulation results show the torque-slip characteristics, stator power factor-rotor voltage and stator current-rotor voltage.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.05a
• /
• pp.69-73
• /
• 2005

The arc dispersion and contacts characteristics were analyzed according to switching off Residual Current Protective Device(RCD) switch. Arc dispersion process was taken by high speed imaging system at a rate of 10,000 frames per second. When RCD was switched from on to off, art was observed and it took about 2.3[ms] from the generation of arc to the extinction of arc. When RCD was switched from off to on, arc was not observed. We repeated switching on and off 1000, 3000 and 6000 times. After repetition, the surface characteristics of contacts were taken by stereo microscope and Scanning Electron Microscope(SEM). From the scattering patterns analysis of arc and the analysis of deteriorated contacts, it could be applicable to the research of electric fire and arc suppression.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1965-1967
• /
• 1999

We have investigated the electrical characteristics of the poly-Si TFT's with the novel gate insulator structure. The gate insulator makes the offset region to reduce leakage current, and the electrical characteristics are obtained by employing Virtual Wafer Fab. simulator. As increases the gate insulator thickness above the offset region of this structure from $0{\AA}$ to $2000{\AA}$, the OFF state current at $V_G$=10V decrease by two orders in magnitude while ON state current doesn't decrease significantly. ON/OFF current ratios for conventional device and the proposed device with $2000{\AA}$ gate insulator thickness are $1.68{\times}10^5$ and $1.07{\times}10^7$, respectively.