• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.2
• /
• pp.157-167
• /
• 2020

Removing radioactive concrete is crucial in the decommissioning of nuclear power plants. However, this process generates radioactive aerosols, exposing workers to radiation. Although large amounts of radioactive concrete are generated during decommissioning, studies on the internal exposure of workers to radioactive aerosols generated from the cutting of radioactive concrete are very limited. In this study, therefore, we calculate the internal radiation doses of workers exposed to radioactive aerosols during activities such as drilling and cutting of radioactive concrete, using previous research data. The electrical-mobility-equivalent diameter measured in a previous study was converted to aerodynamic diameter using the Newton-Raphson method. Furthermore, the specific activity of each nuclide in radioactive concrete 10 years after nuclear power plants are shut down was calculated using the ORIGEN code. Eventually, we calculated the committed effective dose for each nuclide using the IMBA software. The maximum effective dose of ¹⁵²Eu constituted 83.09% of the total dose; moreover, the five highest-ranked elements (¹⁵²Eu, ¹⁵⁴Eu, ⁶⁰Co, ²³⁹Pu, ⁵⁵Fe) constituted 99.63%. Therefore, we postulate that these major elements could be measured first for rapid radiation exposure management of workers involved in decommissioning of nuclear power plants, even if all radioactive elements in concrete are not considered.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.689-696
• /
• 2018

System grounding is applied to the neutral point of a power source to secure the from any abnormal voltage and/or grounding fault. System grounding, which is applied mainly in ships is an ungrounded and resistance grounded system. Vessels using the MV power system with 3.3kV, 6.6kV, and 11kV mainly adopt a high resistance grounding system among the resistance grounding systems. The ground fault accounts for 95% of all faults occurring in the electrical system and when a fault occurs, the line-to-ground voltage of the power system is increased excessively, which adversely affects the onboard insulation system. This study analyzed the variation characteristics of the line-to-ground voltage neutral point according to the degree of ground fault in a resistance ground system applied in vessels. For this purpose, the characteristics of the grounding system were first explained, and the modeling of the neutral point potential of the line-to-ground voltage of the resistance grounding system in the vessels was derived. Finally, this study examined how the line-to-ground voltage, line voltage, and neutral point change according to various variable environments through MATLAB simulations.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.11B
• /
• pp.1383-1388
• /
• 2011

Due to many recent activities on enforcement of the intensified environmental regulation such as the policies of curbing the greenhouse gas and the Restriction of Hazardous Substances (RoHS), the usage of Light emitting diode (LED) has been rapidly increased and energy efficient management of LED light system is regarded as an important technology to enhance the energy efficiency. In this paper, we propose an energy-efficient control scheme of LED light, being composed of multiple light sources. The proposed scheme controls the intensity of LED light source to minimize the total intensity while providing the quality of lighting service. The intensity of light is assumed to be proportional to power consumption, thus the objective is to minimize the total power consumption. A linear programming problem is formulated to find the optimal intensity of each light source and procedure to apply the proposed scheme in the real system is suggested. The performance evaluation results elucidate that the proposed scheme achieves over 20% improvement in power consumption of light intensity in comparison with the conventional dimming control scheme.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.493-500
• /
• 2017

Based on the data accumulated through EMU fault management, this paper examines the reliability of old railway car parts and proposes measurements to improve safety. Subway Line 7 of the Seoul Metropolitan Rapid Transit Corporation, auxiliary power unit (Static Inverter) of the EMU second version is a core equipment to supply power to various room-service units in cars and make an effect directly on passenger satisfaction. To analyze the pattern of failure throughout the field data over a long period of time, this analysis of statistics and reliability considers the operating environment and stress factors. This statistical analysis presents the correlation between failure and the temperature stress factors related to frequent failure occurring intensively in summer. In addition, throughout the analysis of the life of the IGBT inverter, the effect of the temperature stress factor was observed before and after the repair. As a result of an analysis of the optimal operating conditions considering two variations of EMU, such as variable load and outside temperature, a difference in the cooling capacity between the optimal operating conditions and frequent failure conditions was observed. Based on this analysis, this paper suggests a way to minimize cooling capacity difference for the optimal operational conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.285-293
• /
• 2016

In the paper, we propose a data transmission repeating system that allows data transmission for the effective supervision of cows grazing in the pasture. It is normal practice to divide the pasture into different areas for the purpose of distributing the grazing. However, this makes it difficult to supply electrical power and transmit data, because some of the pastures are far away from the office used for collecting data. To solve this problem, we developed a repeating system that can allow data transmission in the pasture using a solar charging system that consists of a 60W solar panel, 12V/100A battery and 6A solar controller for the power supply and a data transmission algorithm which extends the range of data transmission when using the proposed repeating system. We verified the performance of the repeating system by checking whether the data transmission is successful or not when transmitting from various test points when there is an obstacle between the receiver and repeating system. We also verified the solar charging system by measuring the battery voltage when the system is operated continuously for 31 days and whether the system can supply sufficient power when the weather is cloudy or rainy for a few days. Finally, we verified the performance of the repeating system and data transmission algorithm by conducting experiments in a pasture.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.650-656
• /
• 2018

The TFT-LCD industry is a kind of large-scale industrial Giant Microelectronics device industry and has a similar semiconductor process technology. Wet etching forms a relatively large proportion of the entire TFT process, but the number of published research papers on this topic is limited. The main reason for this is that the components of the etchant, in which the reaction takes place, are confidential and rarely publicized. Aluminum (Al) and copper (Cu), which have been used in recent years for the manufacture of large area LCDs, are very difficult materials to process using wet etching. Cu, a low-resistance material, can only be used in the wet etching process, and is used as a substitute for Al due to its high speed etching, low failure rate, and low power consumption. Further, the abnormal reaction of hydrogen peroxide ($H_2O_2$), which is used as an etching solution, requires additional piping and electrical safety devices. This paper proposes a method of minimizing the damage to the plant in the case of adverse reactions, though it cannot limit the adverse reaction of hydrogen peroxide. In recent years, there have been many cases in which aluminum etching equipment has been changed to copper. This paper presents a countermeasure against abnormal reactions by implementing safety PLC with a high safety grade.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.3
• /
• pp.129-134
• /
• 2020

Moisture infiltration inside the solar cell module, filling of EVA sheet, melting of the frame seal, and deterioration of power generation performance in the module one year after installation are occurring. Whitening phenomenon, electrode corrosion phenomenon, and dielectric breakdown phenomenon are appearing in solar cell module installed in Korea before 5-7 years, leading to deterioration of power generation performance, and big problems for long-term reliability and long life technology are emerging. Therefore, in order to solve these problems, the development of a micro inverter (MiCrco Inverter Converter, MiC) including the function of securing the durability of the solar cell module and monitoring the aging progress and the solar cell based on the monitoring data from the MiC smart monitoring programs have been proposed to determine the aging of modules. In addition, in order to become a highly efficient solar smart monitoring system through systematic operation management through IT convergence with MiC that has enhanced monitoring function of solar cell module, SoC(System On Chip) in micro inverter is the environment for solar cell module. There is a demand for functions that can detect information in a complex manner and perform communication and control when necessary. Based on these requirements, this paper aims to develop SoC-based low-cost MiC smart photovoltaic system technology.

• Journal of the Korea Society of Computer and Information
• /
• v.19 no.4
• /
• pp.1-8
• /
• 2014

As cores in multi-core processors are integrated in a single chip, power density increased considerably, resulting in high temperature. For this reason, many research groups have focused on the techniques to solve thermal problems. In general, the approaches using mechanical cooling system or DTM(Dynamic Thermal Management) have been used to reduce the temperature in the microprocessors. However, existing approaches cannot solve thermal problems due to high cost and performance degradation. However, floorplan scheme does not require extra cooling cost and performance degradation. In this paper, we propose the diverse floorplan schemes in order to alleviate the thermal problem caused by the hottest unit in multi-core processors. Simulation results show that the peak temperature can be reduced efficiently when the hottest unit is located near to L2 cache. Compared to baseline floorplan, the peak temperature of core-central and core-edge are decreased by $8.04^{\circ}C$, $8.05^{\circ}C$ on average, respectively.

• Korean Journal of Environment and Ecology
• /
• v.33 no.6
• /
• pp.708-721
• /
• 2019

This study was conducted to understand the plant community structure characteristics of warm-temperate forest in Geoje Island. Survey sites were set up on ridges, valleys, and slopes where evergreen broad-leaved trees predominated or distributed in canopy, sub-canopy, or shrub layers at Chunjangsan(Mt.). Thirty-one sites were located in the areas, such as vegetation community, ridges, valleys, and slopes, to observe vegetation structure and location changes. The community classification with TWINSPAN identified six groups: Neolitsea sericea-Platycarya strobilacea, N. sericea-Styrax japonicus, N. sericea-Euonymus oxyphyllus, Pinus thunbergii-N. sericea, N. sericea-Quercus serrata, and Q. variabilis-P. strobilacea. Considering the results of previous studies that reported that the successional pattern of the warm temperate forests progressed from deciduous to evergreen forests, the regions predominated by deciduous communities such as P. thunbergii, Q. serrata, P. strobilacea, Zelkova serrata, and Q. variabilis, is likely to transform into the evergreen forest predominated by N. sericea. The relationship between the impact of the environmental factors and the vegetation distribution showed that slope, Na +, K +, electrical conductivity, and clay among physical properties had direct or indirect effects on vegetation distribution.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.4
• /
• pp.1-13
• /
• 2014

The paper gives an overview of the concepts, basic requirements, and trends regarding packaging technologies of power modules in hybrid (HEV) and electric vehicles (EV). Power electronics is gaining more and more importance in the automotive sector due to the slow but steady progress of introducing partially or even fully electric powered vehicles. The demands for power electronic devices and systems are manifold, and concerns besides aspects such as energy efficiency, cooling and costs especially robustness and lifetime issues. Higher operation temperatures and the current density increase of new IGBT (Insulated Gate Bipolar Transistor) generations make it more and more complicated to meet the quality requirements for power electronic modules. Especially the increasing heat dissipation inside the silicon (Si) leads to maximum operation temperatures of nearly $200^{\circ}C$. As a result new packaging technologies are needed to face the demands of power modules in the future. Wide-band gap (WBG) semiconductors such as silicon carbide (SiC) or gallium nitride (GaN) have the potential to considerably enhance the energy efficiency and to reduce the weight of power electronic systems in EVs due to their improved electrical and thermal properties in comparison to Si based solutions. In this paper, we will introduce various package materials, advanced packaging technologies, heat dissipation and thermal management of advanced power modules with extended reliability for EV applications. In addition, SiC and GaN based WBG power modules will be introduced.