• Proceedings of the KIEE Conference
• /
• 2001.07a
• /
• pp.377-379
• /
• 2001

When a wide area blackout occurres, reenergizing transmission lines should be done at first. The KEPCO(Korea Electric Power Corporation) divides whole power system grid into seven subsystem, and each subsystem has one of two blackstart power plants which are usually hydro or combined-combustion type, one priority power plant which should be first supplied with electric energy, and transmission lines between them. Voltage rising, line charging, and operation stability problem should be considered when these lines are reenergized. In this paper, building-up process for primary transmission system that should be energized at first is analyzed.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.249-255
• /
• 2011

This paper is about the study of a stand-alone photovoltaic power conditioning system with an energy storage system with battery. The paper proposes the appropriate circuit model of stand-alone PV PCS considering the maintenance of the battery system. It also proposes the buck converter modeling by a state-space averaging method considering characteristics of solar cell. Lastly, it shows the way to choose the suitable battery and to design the model of bi-directional converter for charging and discharging battery. PSIM simulation is used to validate the proposed algothim of the system.

• Proceedings of the KIEE Conference
• /
• 1997.07a
• /
• pp.244-246
• /
• 1997

This paper is to analyze the Premature Quench characteristics of a rotating magnet type superconducting fluxpump and consider the method of detecting and protecting this premature quench. Practically, there is contact resistance between the fluxpump and the load, namely the S.C. magnet. The thermal increase due to the contact resistance cause the premature quench before the charging current amounts to the critical current of S.C magnet. Therefore, this paper is devoted to solving the heat equation on contact region using cylindrical coordinates and to calculating the rate of thermal increase during the current is pumped up. Doing so, the predictive value of the maximum pumping current is obtained. It has been verified that the results of simulation are coincident with those of experiment. It must be considered essentially to minimize the contact resistance in designing the S.C fluxpump system in order to protect the premature quench and improve the maximum pumping current.

• Journal of the Korean Vacuum Society
• /
• v.10 no.1
• /
• pp.72-80
• /
• 2001

In this paper, we present a systematic method of extracting the input parameters of poly-Si TFT(Thin-Film Transistor) for Spice simulations. This method has been applied to two different types of poly-Si TFTs such as ELA (Excimer Laser Annealing) and SMC (Silicide Mediated Crystallization) with good fitting results to experimental data. Among the Spice circuit simulators, the PSpice has the GUI(graphic user interface) feature making the composition of complicated circuits easier. We added successfully the poly-Si TFT model of AIM-Spice to the PSpice simulator, and analyzed easily to compare the electrical characteristics of pixels without or with the line RC delay. In the comparative results, the ELA poly-Si TFT is superior to the SMC poly-Si TFT in the charging time and the kickback voltage for the TFT-LCD (Thin Film Transistor-Liquid Crystal Display).

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.5
• /
• pp.479-490
• /
• 2015

The conventional phase-shifted full-bridge (PSFB) converter with an LC filter has been widely used for high-power applications of over 1.0 kW. However, the PSFB converter cannot obtain optimal power conversion efficiency during the battery charging in electric vehicle (EV) on-board battery charger applications because of its unique drawbacks, such as a large circulating current and very high voltage stress in the rectifier diodes. As a result, the converters with a capacitive filter, such as LLC resonant converters, replace the PSFB converter in the EV chargers. This study analyzes the problems of the PSFB converter for EV on-board charger applications in detail. Moreover, the newest converters based on the conventional PSFB converter are reviewed. On the basis of the reviews, new PSFB converter topologies are proposed for EV charger applications. The new topologies are formed by connecting the rectifier stage in the PSFB converter with the output of an LLC resonant converter in series. Many problems of the conventional PSFB converter for EV charger applications can be solved and the performance can be more improved because of this structure; this idea is confirmed by an experiment consisting of prototype battery chargers under the output voltage range of 250-450 Vdc at 3.3 kW.

• Progress in Superconductivity and Cryogenics
• /
• v.19 no.3
• /
• pp.49-53
• /
• 2017

The superconducting magnets have a large inductance as well as high operating current. Therefore, mega-joule scale energy can be stored in the magnet. The energy stored in the magnet is sufficient to damage the magnet when a quench occurs. Quench heater and dump resistor can be used to protect the magnet. However, using quench heater to create quench resistors through heat transfer can be slower than instantly switching resistors. Also, electrical short, overheating and breakdown can occur due to quench heater. Moreover, the number of dump resistor should be limited to avoid large terminal voltage. Therefore, in this paper, we propose a quench protection method for extracting the energy stored in a magnet by charging and discharging energy through a capacitor switching without increasing resistance. The simulation results show that the proposed system has a faster current decay within the allowable voltage level.

• Current Optics and Photonics
• /
• v.1 no.5
• /
• pp.468-473
• /
• 2017

We determined the feasibility of a fishing camera system using an optical fiber as the fishing line by testing a power-over-fiber (POF) module and multimode optical fiber. Operation of the remote camera module (RCM) without the battery was preferred because the removal of the charging or battery replacement section enabled a waterproof single-body type design. The average efficiency of the photovoltaic power converter (PPC) in the tested POF module was 32.6% at 820 nm, and thus, a high-power laser of at least 1.27 W was required for operating the developed RCM with an electrical dissipation of 413 mW. Because the optical fiber was wound on a fishing reel, composite loss composed of bending and tensile loss occurred. To mitigate the composite loss, we employed a simple holder that showed an improvement in the composite loss of 0.38 dB to 0.8 dB, which was considerably better than the losses without the holder.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.1
• /
• pp.20-28
• /
• 2003

In this paper, we present results of the comparative analysis of the flicker phenomena in the poly-Si TFT-LCD and a-Si:H TFT-LCD arrays for the development and manufacturing of wide-area and high-quality TFT-LCD displays. We used four different types of TFTs; a-Si:H TFT, excimer laser annealed (ELA) poly-Si TFT, silicide mediated crystallization (SMC) poly-Si TFT, and counter-doped lateral body terminal (LBT), poly-Si TFT. We defined the electrical quantity of the flicker so that we could compare the flickers quantitatively for four different 40" UXGA TFT-LCDs. We identify three factors contributing to the flicker, such as charging time, kickback voltage and leakage current, and analyze how much each of three factors give rise to the flincker in the different TFT-LCD arrays. In addition, we suggest and show that, in the case of the poly-Si TFT-LCD arrays, the low-level (minimum) gate voltages should be carefully chosen to minimize the flicker because of their larger leakage currents compared with a-Si TFT-LCD arrays.

• Ceramist
• /
• v.22 no.2
• /
• pp.122-132
• /
• 2019

Wearable electronic devices with batteries must be lightweight, flexible and highly durable. Most importantly, the battery should be able to self-generate to operate the devices without having to be too frequently charged externally. An eco-friendly energy harvesting technology from various sources, such as solar energy, electromagnetic energy and wind energy, has been developed for a self-charging flexible battery. Although the energy harvesting from such sources are often unstable according to the surrounding environment, the energy harvesting from body movements and vibrations has been less affected by the surrounding environment. In this regard, flexible piezoelectric modules are the most attractive solution for this issue, because they convert mechanical energy to electrical energy and harvest energy from the human body motions. Among the various flexible piezoelectric modules, piezoelectric nanofibers have advantages when used as an energy harvester in wearable devices, due to their simple manufacturing process with good applicability to polymers and ceramics. This review focused on diverse flexible piezoelectric nanofibers and discusses their applications as various energy harvesting systems.

• Journal of Power Electronics
• /
• v.13 no.3
• /
• pp.429-436
• /
• 2013

Online simulations are utilized to reduce time and cost in the development and performance optimization of plug-in hybrid electric vehicle (PHEV) and electric vehicles (EV) systems. One of the most important factors in an online simulation is the accuracy of the model. In particular, a model of a battery should accurately reflect the properties of an actual battery. However, precise dynamic modeling of high-capacity battery systems, which significantly affects the performance of a PHEV, is difficult because of its nonlinear electrochemical characteristics. In this study, a dynamic model of a high-capacity battery cell for a PHEV is developed through the extraction of the equivalent impedance parameters using electrochemical impedance spectroscopy (EIS). Based on the extracted parameters, a battery cell model is implemented using MATLAB/Simulink, and charging/discharging profiles are executed for comparative verification. Based on the obtained results, the model is optimized for a high-capacity battery cell for a PHEV. The simulation results show good agreement with the experimental results, thereby validating the developed model and verifying its accuracy.