• Proceedings of the KIEE Conference
• /
• 1993.07a
• /
• pp.464-466
• /
• 1993

In this paper, a peak detection algorithm having high reliability is proposed. The peak detection algorithm is implemented to a charger and power control system which is applicable to home appliances or notebook PC directly. The charger and power control system is controlled by a microprocessor, M50927 (Mitzubishi), to improve cost to performance ratio. The charger algorithm is designed to be operated under optimal charge node and various protections are added tn improve the reliability of the charger.

• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.297-299
• /
• 2000

본 논문은 휴대용 기기 충전을 위한 영구 자석형 선형 발전기의 특성 해석을 담고 있다. 발생된 전력의 크기와 용량, 충방전 시간 측정을 포함하고 있으며, 전압 평활화에 따른 결과 역시 고려하였다.

• Journal of Sensor Science and Technology
• /
• v.5 no.3
• /
• pp.33-40
• /
• 1996

$(Ba_{0.5}\;Ca_{0.5})TiO_{3}$ humidity-sensitive devices were fabricated by a solid reaction method, and their electrical properties were investigated. The specimens exhibited good humidity sensitivity, in which the impedance changes linearly. It is shown that electrical conduction with moisture adsorption is dominated by the ions through characteristics of charging and discharing current, and electrical conductivity increases as rasing the temperature and relative humidity. It is realized that relative permittivity increases and activation energy decreases with increasing relative humidity.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.3
• /
• pp.27-34
• /
• 2005

This paper presents a three phase Line-Interactive uninterruptible power supply(UPS) system with dual converter structure. The three phase UPS system consists of two active power compensator topologies. One is a series active compensator, which works as a voltage source in phase with the source voltage to have the sinusoidal source current and high power factor under the deviation and distortion of the source voltage. The other is a parallel active compensator, which works as a conventional sinusoidal voltage source in phase with the source voltage, providing to the load a regulated and sinusoidal voltage with low total harmonic distortion(THD). This paper presents in the series and parallel active compensator charging method depending on the amplitude of the source voltage. The conventional Line-Interactive UPS system is responsible for the DC charging and output voltage regulation at the same time, but UPS system with dual converter structure, a series active compensator can also charge the DC link. Therefore the charging algorithm using the series and parallel compensator needs to be researched. Therefore, by making the DC link voltage stable it can contribute the stability of series and parallel compensator. The simulation and experimental result are depicted in this paper to show the effect of the proposed algorithm.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.999-1002
• /
• 2004

We propose and simulate a new integrated DAC analog buffer composed of only p-type poly-Si TFTs in AMLCD and AMOLED. Proposed circuit employs a voltage level shifter which $V_{OUT}$ has a linear functional relation to $V_{IN}$. The proposed scheme enables to allow a constant $V_{GS}$ of buffer transistor so that the charging speed of pixel data address is improved.

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.1
• /
• pp.92-96
• /
• 2003

This paper deals with the characteristics of persistent current switch (rCS) system fer applied HTS magnet system. To apply the high-Tc superconductor in superconducting machine such as motror, generator, MAGLEV, MRI, and NMR, the study on high-Tc superconducting persistent current mode must be performed. In this experiment, the PCS system consists otd superconducting magnet, PCS and magnet power supply. The superconducting magnet was fabricated by connecting four double pancake coils (DPCs) in series. The PCS was inductive double pancake coil type and heated up by the SUS 303L tape heater. The optimal length of PCS was calculated and thermal quench state of PCS was simulated by using finite element method(FEM) and compared with experimental results. The optimal energy to normalize the PCS was calculated and introduced. Finally, the persistent current was observed with respect to various ramping up rate and magnitude of charging current.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.486-491
• /
• 1991

The photovoltaic modules have each maximum power point, which depending on the intensity of sunlight, modules temperature and etc. Cuk converter is used to obtain the maximum charging power from photovoltaic modules to storage batteries. This paper proposed to a new tracking control method by detecting its current and voltage in photovoltaic power generation system controlled by microprocessor, in order to operate at the maximum power point tracking(MPPT) even if the sunlight and the temperature are varied.

• Journal of Sensor Science and Technology
• /
• v.28 no.6
• /
• pp.407-413
• /
• 2019

Using 3D printing technology, we created a biomimetic water strider robot that can monitor environments. We found ways to increase the bearing capacity of the fluid-driven water strider robot by conducting experiments then comparing with more stable robots. The controller of the robot is based on Arduino, and can be controlled wirelessly with a Bluetooth module. The speed of the robot is 7.37 cm/s, and the bearing capacity is 29 g. A lithium polymer battery that can be charged with a solar cell was used as a power source, and both the charging and driving times were also explored.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.5
• /
• pp.2043-2050
• /
• 2017

This paper presents two MPC (Model Predictive Control) based charging and discharging algorithms of BESS (Battery Energy Storage System) for capacity firming of wind generation. To deal with the intermittency of the output of wind generation, a single BESS is employed. The proposed algorithms not only make the output of combined systems of wind generation and BESS track the predefined reference, but also keep the SoC (State of Charge) of BESS within its physical limitation. Since the proposed algorithms are both presented in simple if-then statements which are the optimal solutions of related optimization problems, they are both easy to implement in a real-time system. Finally, simulations of the two strategies are done using a realistic wind farm library and a BESS model. The results on both simulations show that the proposed algorithms effectively achieve capacity firming while fulfilling all physical constraints.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.2
• /
• pp.111-115
• /
• 2012

In this paper, a solar energy powered bicycle linked to a wireless sensor network (WSN) which monitors the transfer of solar energy to an electrical energy storage unit and an analysis of its effectiveness is proposed. In order to achieve this goal, a solar-powered bicycle with an attached ZigBee and a far-end wireless network supervisory system is setup. Experimental results prove that our prototype, solar energy powered bicycle, can achieve enough solar energy for charging a two lead-acid battery pack. As a result, the user, through use of a wireless network in the parking period can be kept aware of the data on the amount of immediate solar radiation, the degree of illumination, the ambient temperature, and electrical energy storage capacity information of the bicycle through an internet interface.