• Electrical & Electronic Materials
• /
• v.9 no.1
• /
• pp.24-29
• /
• 1996

A composite piezoelectric ceramic transducer is fabricated with three piezoelectric ceramic disk vibrators and two sheets of thin insulator. Its equivalent circuit is derived from the Mason's model of a thickness-driven piezoelectric vibrator. When the electric input near its fundamental resonance frequency is applied to the center vibrator and the output voltages across the left and the right vibrators are connected in series to the resistor loads, the load characteristics at resonance frequencies under the various resistor loads and the frequency characteristics near the resonance frequency without load are investigated. Furthermore, symbolic expressions for input impedances, voltage ratios, resonance frequencies, and bandwidths are derived. The data calculated from those symbolic expressions are agreed well with the measurement data.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.05a
• /
• pp.293-296
• /
• 2009

In order to protect the electrical fire, AFCI(Arc Fault Cirruit Interrupter) was obligated to adopted in United States of America since 2002. AFCI using by line resistor of neutral trace needs to compensate the resistance variation of the line resistor by temperature variation. In this paper, the ASIC including the temperature compensation circuit is implemented. The successful implementation is verified by showing the effectiveness of an electric and a temperature characteristics for ARC signals by simulation results.

• Journal of Magnetics
• /
• v.17 no.4
• /
• pp.285-290
• /
• 2012

Electric Power Steering (EPS) system is superior to conventional Hydraulic Power Steering (HPS) system in aspect of fuel economy and environmental concerns. The EPS system consists of torque sensor, electric motor, ECU (Electric Control Unit), gears and etc. Among the elements, the torque sensor is one of the core technologies of which output signal is used for main input of EPS controller. Usually, the torque sensor has used torsion bar to transform torsion angle into torque and needs linear characteristic in terms of flux variation with respect to rotation angle of permanent magnet. The torsion angle of both ends of a torsion bar is measured by a contact variable resistor. In this paper, the sensor is accurately analyzed using 3D finite element method and its characteristics with respect to four different shapes of the stator teeth are compared. The four shapes are rectangular, triangular, trapezoidal and circular type.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.313-316
• /
• 2002

A SRM inverter has very low switching frequency. This results in reducing the burden for a high-speed of the gate-amp interface circuit. and the linearity of optocoupler is used to protect the intanteneous peak current for the stable operation In this paper, series resistor is used to equal the current sharing of each switching device and a linear gate-amp is proposed to protect the intanteneous peak current which occurs in transient state.

• Proceedings of the KIEE Conference
• /
• 1997.07e
• /
• pp.1688-1691
• /
• 1997

In this work, we have developed the off-line diagnostic system for power cable insulation using DC voltage decay method to diagnose the insulation degradation of underground power cables. Measurement errors of diagnostic system are less than 1% for $1T{\Omega}$ internal resistor. We have also developed measurement and diagnostic programs for win95 which is suitable for the database construction and the management of data. We could conclude that it is possible to apply this system to the multi-grounded underground cable systems.

• Journal of the Korea Safety Management & Science
• /
• v.23 no.3
• /
• pp.103-113
• /
• 2021

As the use of capacitors in electrical appliances and electrical control circuits increases, the related electrical fire is increasing. There are various parts such as resistors, coils, and capacitors that make up an electric circuit. Among them, the ignition of a capacitor with a temporary charging function is closely related to the structural characteristics of the capacitor. Capacitors can explode due to various reasons, and the high heat generated when they explode ignites the inflammable dielectric, which in turn burns the inflammable materials such as the surrounding electric wires and spreads into a fire. In this paper, the ignition mechanism is studied by conducting a reenactment experiment on the various probabilities that can be ignited in an electric capacitor, and the prevention measures to be applied to the fire prevention are presented.

• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.114-119
• /
• 2006

High critical current density, high n value, multiple faults endurances, and fast recovery characteristics of YBCO thin films are very attractive characteristics for developing resistive type superconducting fault current limiters. But due to the limited current and voltage ratings of one YBCO module, it is needed to construct series and parallel module connections for high capacity electric networks. Especially for distribution network, more than 30 units should be connected in series to meet voltage level. So in order to construct distribution-level superconducting fault current limiter, simultaneous quench in one YBCO thin films should be realized, and furthermore, quench should be occurred in all fault current limiting units equally to avoid local heating and failures. In this paper, we proposed optimum design of YBCO thin films for fault current limiting module and technical method using shunt resistor to achieve simultaneous quench between multi current limiting units. From the analytical and the experimental results, optimal current path and thickness of shunt material was determined for YBCO thin films and shunt resistor between modules was developed. Finally, 14 kV one phase resistive fault current limiter using multi YBCO thin films was constructed and it was possible to get satisfactory test results.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.702_703
• /
• 2009

Electric Power Steering(EPS) system is superior to conventional Hydraulic Power Steering(HPS) system in aspect of fuel economy and environmental concerns. The EPS system consists of torque sensor, electric motor, ECU(Electric Control Unit), gears and etc. Among the elements, the torque sensor is one of the core technologies of which output signal is used for main input of EPS controller. Usually, the torque sensor has used torsion bar to transform torsion angle into torque. The torsion angle of both ends of a torsion bar is measured by a contact variable resistor. In this paper, the sensor is accurately analyzed using 3D finite element method and its characteristics with respect to four different shapes of the stator teeth are compared. The four shapes are rectangular, triangular, trapezoidal and circular type.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10b
• /
• pp.1420-1423
• /
• 1990

DC series motor has been widely applicated in industry due to many advantageous characteristics, such as high starting torque, easy construction of its controller, and cost economy, etc.. However, by high starting current, excessive surge voltage, and so on, many problems which could make engineers relinguish to use it are induced. In this paper, various protection methods for power circuit are discussed. Particularly, a new proposed snubber circuit which consists of two diodes, one capacitor, and a resistor increases the performance with respect to the suppression of the surge voltage. Furthermore, the plugging algorithm, by checking the armature current and voltage and controlling the field coil current, is designed and implemented. Also, these methods and algorithms were applicated in electric vehicle, and we could find its stability to be considerably improved.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.1914-1918
• /
• 1998

In the case of synchronous machines, certain power system disturbances cause the induced rotor current to assume negative values when no static converter is present. A converter, however. prevents negative current from flowing, so that overvoltages occur. The overvoltages can be effectively limited as crowbar circuit using GTO. This newly proposed crowbar circuit with current limiting resistor absorbs energy when overvoltage comes from power system repeatedly and is verified through experiment.