• Journal of the Korean Society for Railway
• /
• v.12 no.6
• /
• pp.902-908
• /
• 2009

TETRA is the standard of Digital Trunked Radio System developed by the ETSI (European Telecommunications Standards Institute). It is currently adopted as Electric Power IT Wireless Backbone Network in Korea, and a national enterprise is going on for versatile utilization of TETRA. To use TETRA wireless network, TETRA modem is very necessary such that performance measurements are very crucial for each TETRA modem by various manufacturers. In this paper, PED (Protocol Evaluation Data) is suggested for PD performance measurement in D-TRS wireless network environment. The performance measurements for different data lengths and transmission intervals are done using TG (Traffic Generator) on Test Bed. The data size is increased by 10 bytes from 10-byte to 400-byte, and it is measured 1,000 times for each transmission interval of 0.5, 1.0, and 1.5 seconds. Based on the transmission time measured, average transmission speed and MER (Message Error Rate) are derived for TETRA Modem performance measurement. Two TMR880i's of EADS are used for TETRA modem, and SwMI (Switching and Management Infrastructure) of EADS is used for switching system in this paper.

• Journal of the Korean Society for Railway
• /
• v.12 no.2
• /
• pp.249-253
• /
• 2009

This paper dealt with the insulation evaluation by a measurement of partial discharge(PD) on traction motors used in a hybrid vehicle. The PD method has been accepted as an effective and a non-destructive. technique to evaluate insulation performance of low-voltage electric and electronic devices. In this paper, the PD measurement system which was manufactured with a coupling network, a low noise amplifier, and an associated electronics is described. The PD measurement system has the frequency bandwidth of $1[MHz]{\sim}30[MHz]$ at -3 [dB] and the stable sensitivity of 19 [mV/pC] for the traction motor. From the experimental results, discharge inception voltage (DIV) and apparent charge (q) were $1,100[V_{rms}]$ and 105 [pC] for the used motor, and $1,400[V_{rms}]$ and 84 [pC] for the new one. By comparing the DIV and q, we could evaluate the insulation condition for the traction motors.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.9
• /
• pp.1343-1347
• /
• 2013

This paper presents an analysis methods for current collection quality in catenary system by means of video image based monitoring system. Arcing is the sparking at the interface point between pantograph and contact wire when the electric trains have traction current values at speed. Percentage of arcing at maximum line speed is measurable parameters for compliance with the requirements on dynamic behaviour of the interface between pantograph and contact wire in accordance with requirement of IEC and EN standards. The arc detector and video is installed on a train aim at the trailing contact strip according to the travel direction. The arc detector presented and measured verity of value such as the duration and power density of each arc and the video image is measured a image when the arc is occurred in pantograph. In this paper we analysis of video image in accordance with power density of arcing from arc detector and compared with video image and power density of arcing so as to produce quality of arcing from image.

• Journal of KSNVE
• /
• v.7 no.3
• /
• pp.369-376
• /
• 1997

With recent progress of developing infrastructure, construction vibration from the sites and traffic vibration caused by high-speed rail, subway, and roads is becoming a hazardous factor for vibration environment. In order to predict the damages caused by the vibrations mentioned above the vibration sources, have to be distinguished between point vibration and line vibration. Once the character of the vibration source is determined vibration propagation phenomenon needs to be analyzed by using prediction formula, and compared to the limits authorized by the law. The main purpose of this thesis is to manage the efficient vibration by reflecting these finding in making a consrtuction plan. Therefore, Vibration Management System (VMS) was developed which can predict and analyze the extent of developed utilizing Geographic Information System (GIS) to build a database. This database contains the attribute and the location information of the sources for predicting the formula of explosive vibration and subway traffic vibration, the buildings, the surrounding area and measurement sites. VMS will be useful in the future for predicting the vibrations caused by pile drive, traffic vibrations such as high speed electric railway, highway and roads, and other explosive vibrations by supplementing and updating the database.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.133-138
• /
• 2010

This paper describes on aerodynamic characteristics of pantograph system for Next generation high speed train(HEMU-400). The pantograph which supports electric power is located on the roof. Because of this, it generate high drag, severe acoustic noise and vibration which induced unstable flow due to complex configuration. Therefore, the design of high efficient pantograph needs to increase operational speed. In this research, wind tunnel tests were performed to design a high efficient pantograph system using 1/4 scaled model which were KTX-II pantograph, single arm pantograph and periscope type pantograph with square cylinder shape panhead and optimized shape panhead. For real operational condition, flow directions were adapted by rotation of pantograph. From this results of wind tunnel, it is checked that the pantograph with optimized panhead and single arm type or periscope type has better aerodynamic performance. In addition, lift control device and spoiler in pantograph were tested to investigate the validity of application.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.872-898
• /
• 2007

Pantograph sliding plate abrasion auto-detect system, one of the electric rail car auto-detecting devices, is a system that decides how much abrasion and when to replace without an inspector physically looking at the abrasion on the wet plate using machine vision, a cutting-edge technology. This paper covers the cause of deteriorating reliability that affects pantograph wet plate edge detection due to noise added to the video when it rains. In order to remove such noise, problems should be checked through Smoothing, Averaging mask and Median filter using filtering technique and stable edge detection without being affected by noise should be induced in video measurement used in machine vision technology.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.11
• /
• pp.2171-2175
• /
• 2011

The objective of this paper is to discuss technologies on assessing reliability of arc detectors by composing a system that generates and simulates occurrence of arc caused by loss of contact between pantographs and contact wires in a laboratory condition. In order to establish the arc simulator, a device that generates light having the bandwidth of arcs that occur between carbon-metal. The simulator was designed under conditions of EN 50317 and simulations were conducted using the developed device. According to the results, it was possible to conduct certification tests following regulations of international standards and the precision of the simulator was satisfactory. The proposed arc detector assessment system is expected to enhance precision of current collection quality performance assessment methods at high-speed lines and conventional lines while being referred as fundamental technologies for development of detectors suiting international conditions.

• Journal of Satellite, Information and Communications
• /
• v.2 no.2
• /
• pp.69-74
• /
• 2007

Recently, the demands for the satellite broadband mobile communication services are increased. To provide these services, mobile satellite communication systems for the passengers or crews on the high-speed moving vehicles, are being developed for the last several years especially in the Europe and North America. However, most of these systems can provide only several hundred kbps of transmission rate and this is not enough performance to provide satellite internet service for the group users such as passengers on the high-speed train. Moreover, service availability with these systems is limited to be rather low because they don't have any countermeasure scheme for the N-LOS environment which happens often along the railway. This paper describes mobile broadband satellite communication system, which is on the development, to provide high data-rate internet services to the high-speed trains. This system is applied with the inter-networking scenarios of both satellite/terrestrial network and satellite/gap-filler network so that it can provide seamless service even in the train operating environment, and these inter-networking schemes result in high service availability. And this system also has the countermeasure schemes, such as upper layer FEC and antenna diversity, for the short fading which is occurred periodically on the railway due to the power supplying structures so that it can provide high speed internet services. Mobile DVB-S2 technology which is now being standardized in the DVB is used for the forward-link transmission and DVB-RCS for the return-link.

• Journal of the Korean Society for Railway
• /
• v.18 no.2
• /
• pp.139-148
• /
• 2015

By increasing the vertical stiffness of the rail fastening system, the dynamic wheel load of the vehicle can be increased on the ballast track, though this increases the cost of track maintenance. On the other hand, the resistance acting on the wheel is decreased, which lowers the cost of the electric power to run the train. For this reason, the determination of the optimal fastener stiffness is important when attempting to minimize the economic costs associated with both track maintenance and energy to operate the train. In this study, a numerical method for evaluating the optimal vertical stiffness of the fasteners used on ballast track is presented on the basis of the process proposed by L$\acute{o}$pez-Pita et al. They used an approximation formula while calculating the dynamic wheel load. The evaluated fastener stiffness is mainly affected by the calculated dynamic wheel load. In this study, the dynamic wheel load is more precisely evaluated with an advanced vehicle-track interaction model. An appropriate range of the stiffness of the fastener applicable to the design of ballast track along domestic high-speed lines is proposed.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.1
• /
• pp.143-153
• /
• 2014

This paper presents a novel application of LCC resonant converter for 60kW EV fast charger and describes development of the high efficiency 60kW EV fast charger. The proposed converter has the advantage of improving the system efficiency especially at the rated load condition because it can reduce the conduction loss by improving the resonance current shape as well as the switching loss by increasing lossless snubber capacitance. Additionally, the simple gate driver circuit suitable for proposed topology is designed. Distinctive features of the proposed converter were analyzed depending on the operation modes and detail design procedure of the 10kW EV fast charger converter module using proposed converter topology were described. The proposed converter and the gate driver were identified through PSpice simulation. The 60kW EV fast charger which generates output voltage ranges from 50V to 500V and maximum 150A of output currents using six parallel operated 10kW converter modules were designed and implemented. Using 60kW fast charger, the charging experiments for three types of high-capacity batteries were performed which have a different charging voltage and current. From the simulation and experimental results, it is verified that the proposed converter topology can be effectively used as main converter topology for EV fast charger.