• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.11
• /
• pp.3115-3120
• /
• 2009

An electric point-machine which changes over a turnout so that it enables a train to be operated in the routine that a train is to proceed has been installed and used in most of the railways such as not only urban railways but also main-line railways. Most of the maintenance works in this electric point-machine is that the maintenance workers manually measure motor power, control power and display power in the site with the use of portable counters. Especially in case of NS or NS-AM electric point machine, the maintenance cycle is so frequent that during the operation casualty accidents caused by carelessness occurs as well as more staff is required for this measurement. In this paper we propose a system for monitoring the state of electric point machine installed in the site to improve maintenance efficiency and it is expected that this monitoring system confirms any measured values on electric point machines in real-time and improves maintenance efficiency.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.12
• /
• pp.1821-1829
• /
• 2017

A point machine requires lots of time and attention in terms of maintenance, since it causes 40% of failures among the railway signaling devices. The senescence of the point machine critically matters to the overall turnout system. In this paper, we analyzed the aging characteristics of the point machine by using the switching current of the point machine. The analysis is done based on the switching current measurements of the point machines deployed in the Sehwa outdoor test site and the Korail Kyongbu line. It is expected that the analysis result can be utilized for real-time diagnosis in the aspect of the maintenance of the point machines and predicting abnormal operations.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.10a
• /
• pp.48-53
• /
• 1998

In this paper, the new electrochemical machining method is proposed for the micro unit fabrication by using the point electrode tools. The precision shape control capacity is improved by using the point electrode method. It was observed that an electric discharge phenomenon occurs during the electrochemical machining process by using the spraying and torrent type electrolyte supply method.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.750-752
• /
• 2003

This paper presents a method of tolerance analysis for a electric machine. Tolerance analysis technique is required to find the tolerance band of design variables and estimate the characteristic distribution of the electric machine, because that manufacturing tolerances as well as measuring errors have a great influence on the electric machine. Therefore, this paper introduces Stochastic Response Surface Methodology to achieve the tolerance analysis. As an example, the tolerance analysis is applied to the analysis of torque characteristics for a BLDC motor from the electric point of view.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.5
• /
• pp.93-99
• /
• 2002

In general, manufacturing error is originated from bad material, machine tool defection and tool breakage. When the manufacturing process is stable, the most of error come from the tool wear. In common on-machine measurement teaching probe and touch sensor are widely used however in this paper the electric touch point type automatic tool compensation system is developed the performance of it is validated and effective operating is proposed.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.100-105
• /
• 2002

In general, manufacturing error originated in bad material, machine tool defection, tool defection, and tool breakage. When the manufacturing process is stable, the error is come from the tool wear. In common on-machine measurement, teaching probe and touch sensor are widely used, however in this thesis the automatic tool compensation system using electric touch point measuring system is developed and evaluated, and effective operating is proposed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.906-909
• /
• 2000

To improve dimension accuracy and make very small parts are one of the major purpose on the electrochemical micromachining. This paper introduce a small machine tool by using the point electrode. That has a data acquisition system for gathering applied electric condition between the gap. Point electrode on this system was made by this method as well. It was found that variable phenomena occurred through the acquired V-I curve on the process.

• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.6
• /
• pp.791-799
• /
• 1999

The purpose of this study was to investigate the displacements of cast framework by torch soldering and electric soldering techniques. Specimen had two cylinders and connecting bar that had sectioned with 0.3mm gap at mid point. 10 of total specimens were divided into two groups. In torch soldered group, soldering investment block was made and conventional torch solder-ing procedure was carried out. In electric soldered group, electric soldering was carried out on the master cast without soldering investment block by using electric soldering machine(Dentapunkt DP 7, Kulzer, Germany) After soldering procedure, three dimensional coordinates of two centroids of each cylinder were measured by three dimensional coordinate measuring machine. The intercentroidal displacement and global displacement were calculated and then, these values were compared and evaluated. The results were obtained as follows: 1. Intercentroidal distances of specimens decreased after both soldering procedures, and the decrease in intercentroidal distance was greater for torch soldered group than for electric soldered group 2. Global displacements of torch soldered group were greater than those of electric soldered group.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2019.05a
• /
• pp.400-402
• /
• 2019

The electric point machine, which is used for the control of the turnout used to change the track of the train, is very important in the railway system. Various wired and wireless real-time monitoring systems are used to check the status of the point machine, but there is a possibility of malfunction due to sensor or network error. In this paper, a redundant monitoring system was designed that incorporates the point machine monitoring system and the CCTV camera control system to double check the operation of the point machine. In the point machine monitoring system, the operating state of the railway converter is monitored, alarmed and transmitted over the network. The CCTV camera control system, which received this information, was required to record the status of the turnout and the point machine in question and send it to the administrator. The manager of the railway line can check the conversion status of the railway through the monitoring screen for the railway line switcher first, and then confirm the switching status directly through the CCTV camera image, thereby improving the reliability of the point machine operation. It will also enable the safe and efficient operation of personnel for management. It is expected to contribute to preventing a derailment caused by a malfunction of the point machine.

• Journal of Powder Materials
• /
• v.12 no.5 s.52
• /
• pp.351-356
• /
• 2005

Nanoscale Al powder with thin layer of alumina was produced by Wire Electric Explosion (WEE) process. Spark-Plasma Sintering (SPS) was performed for the produced powder to confirm the effectiveness of SPS like so-called 'surface-cleaning effect' and so on. Crystallite size and alumina content of produced powder varied with the ratio of input energy to sublimation energy of Al wire ($e/e_s$): Increase in ($e/e_s$) resulted in the decrease of crystallite size and the increase of alumina content. Shrinkage curve during SPS process showed that the oxide surface layer could not be destroyed near the melting point of Al. It implied that there was not enough or no spark-plasma effect during SPS for Al/Alumina powder.