• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.5
• /
• pp.569-575
• /
• 2020

In this study, a fuel cell system model for ship power was developed and verified by comparing the experimental results obtained by supplying pure oxygen. To verify the proposed model, the fuel cell output characteristics when oxygen was supplied were compared with those when air was supplied using an air compressor. In addition, the effect of the change in the thermal properties of the fuel cell system on the output of the stack was examined. Within the experimental range of this study, when pure oxygen was supplied as the cathode supply gas, the calculated and experimental voltages and outputs obtained through modeling were almost the same over the entire load range. When air was supplied instead of oxygen for the cathode supply at a constant load of 560 A, each stack voltage was approximately 14 V, the stack output was approximately 8 kW, and the stack efficiency was approximately 3 %. It was confirmed that the overall system efficiency was reduced by approximately 8 %. Among the thermal properties examined in this study, the heat transfer coefficient of the coolant to the stack was found to have the greatest effect on the output of the stack.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.4
• /
• pp.258-266
• /
• 2011

Scale induced by hardness materials in water must be controled because of it can be result in remarkable damages of pipeline as well as water quality deterioration. Especially hot water system is one of scale management required facility as scale formation can be accelerated by temperature. The scale control performance of frequency driver (FD) was tested instead of existing methods such as chemical, physical and electromagnetic methods which needs chemicals and electric power. Three kinds of pipe coupons were submerged in test water with 500 mg/L of hardness for 33 days and XRD and SEM were analysed for comparing scale formation characteristics of these coupons. Calcite ($CaCO_3$) which came from hardness of water was formed on only cast iron pipe coupon and this coupon showed higher corrosion rate than copper and stainless steel pipe coupon. Hot water circulating system connected cast iron pipe with and without FD was operated with 300 mg/L of hardness water at $50^{\circ}C$ for monitoring of scale formation and water quality with and without FD. XRD showed that FD leaded to magnetite ($Fe_3O_4$) scale which is good scale for preventing corrosion than calcite and SEM image also indicated the scale control effect of FD. Scales of 16% on pipe joint, 14% on pipe length, and 42% on heat exchanger decreased with FD comparing scales of those parts without FD. From the results of water quality, FD reduced crystallization of hardness material without chemical reaction in water and it can indicate that FD is safe and proenvironmental technology for scale reduction.

• Journal of Bio-Environment Control
• /
• v.12 no.2
• /
• pp.83-88
• /
• 2003

The effect of vertical stratification of perlite by particle size on the growth and yield of tomato In a recycling hydroponics was examined. Vertical stratifications were composed of mixed form of small medium and large size (MP), divided forms of small and large size (smal1/1arge, DP I), and medium and large size (medium/large, DP II). Tomatoes showed higher growth in divided form, specially in DP II than DP I. Deformed fruits had higher occurrence by 17.8% in the mixed form than divided forms, while they were not significantly different between mixed forms. Root activity tended to increase during 20 days to 50 days after transplanting (DAT) in all treatments, but showed highest value at 50 DAT in DP II. After harvest electric conductivity and pH of stratified perlite were slightly higher in upper zone of DP I, but were not different in the other treatments. Mineral contents in the medium after harvest were higher in lower zone than the upper zone in MP and DP II, but vice versa in DP I.

• Journal of Bio-Environment Control
• /
• v.14 no.4
• /
• pp.269-274
• /
• 2005

The purpose of this experiment was to investigate optimal ionic concentration of nutrient solution for water culture of young welsh onion (Allium fistulosum). For the purpose of clarification of optimal nutrient concentration to maximize growth of young welsh onion, different nutrient concentrations of Yamazaki's solution for welsh onion seedling $(NO_3^--N\;9.0,\;NH_4^+-N\;3.0,\;PO_4^{3-}-P\;6.0,\;K^+7.0,\;Ca^{2+}\;2.0,\;Mg^{2+}\;2.0,\;and\;SO_4^{2-}-S\;4.4me{\cdot}L^{-1})$ which selected by prior experiment were treated as 0.6, 1.2, 1.8, and $2.4dS{\cdot}m^{-1}$. Increments of fresh weight, dry weight and top length were the highest in 1.2 and, in the next, were placed by the order of 1.8, 2.4, and $0.6dS{\cdot}m^{-1}$ The regression coefficients for the maximal growth of fresh weight of cv. 'Geurnjanguedaepa' and 'Tokyokuro' were $y=-42.091x^2+171.79x+11.047 (R^2=0.8946,\; R=0.9458^*)\;and\;y=-50.069x2+157.58x+15.414(R^2=0.9343,\;R=0.9692^{**})$, respectively, and optimal EC levels according to regression coefficients were 1.68 and $1.57dS{\cdot}m^{-1}$. As the conclusions, optimal nutrient levels far young welsh onion were $1.2dS{\cdot}m^{-1}$ EC in the early growth stage and $1.6\~l .7dS{\cdot}m^{-1}$ in the later growth stage.

• Journal of Bio-Environment Control
• /
• v.18 no.3
• /
• pp.225-231
• /
• 2009

'Nokkwang' green pepper plants were grown in soil system (silty loam with pH 6.5) under the greenhouse, to determine the effects of subsurface drip irrigation (SDI) and subsurface drip irrigation plus aeration (SDIA) into root zone comparing with conventional surface drip irrigation (DI) in terms of water use efficiency, soil properties, and growth and fruit yield. Two drip lines per crop row were layed on the soil surface in DI system, buried at a depth of 20cm below the soil surface in SDI system, and also buried at a depth of20cm below the soil surface and aerated for 3minutes a hour during the daytime ($08:00{\sim}19:00$) by a air compressor in SDIA system. A automatic irrigation with starting point of -20kPa and ending point of -10kPa based on soil moisture contents was applied by controllers and electronic vacum soil moisture sensors. Reduction in soil moisture contents was delayed in SDI and SDIA, compared to DI. Irrigation amount applied in pepper cultivation was around 30% less in SDI than in DI. Electric conductivity and nitrate nitrogen content in the surface soil grown green pepper were significantly lowered in SSDI and SDIA, compared to DI. Better development of root system was observed in SDIA and SDI than in DI. Results showed that pepper fruit yield increased by 30% in SDIA and 22% in SDI in comparision with DI.

• Journal of Bio-Environment Control
• /
• v.17 no.2
• /
• pp.138-142
• /
• 2008

To develop suitable alternative substrates in hydroponics of sweet pepper, changes of water contents of substrates and electric conductivity (EC) of drainage nutrient solution, growth and fruit characteristics according to the kind of coir substrates were investigated compared with rockwool. In all coir substrates compared with rockwool during growing period, water contents were higher, EC of drainage nutrient solution except for fiber 50% were lower, and the coefficient of variation were a little, especially were so in fiber 30% of coir substrates. Plant growth in fiber 30% substrate was better than others but there was no significant difference. Photosynthesis rate and chlorophyll content were best in fiber 50% substrate. Fruit weight was no significant difference, but LID ratio and shape of the fruits were good in fiber 50% substrate and rockwool as which were close to regular square. Therefore, it was estimated that mixed coir substrates with fiber $30{\sim}50%$ are enough in possibility as alternative substrate.

• Journal of Digital Contents Society
• /
• v.19 no.8
• /
• pp.1585-1592
• /
• 2018

Due to un-balancing weight allocation on the wheelchair the existing wheelchair system are faced with the risk of flipping or falling when a wheelchair goes up to a hill. In to order to be safer during riding the wheelchair, in this paper, we proposed a real-time new solution using the integrated Gyro Sensor and Tilt Sensor for controlling the balance. Because the typical property of wheelchair is for the special user who meets the difficulty in moving on foot the maintain the balance of wheel-chair systems have become important and helpful. In our method, we calculate the seat angle using information from Tilt Sensor. However, due to the law of inertia when a wheelchair is moving there is a deviation in the output value of Tilt Sensor. Therefore, we have to optimize the value of the angle by utilizing the acceleration that is the output of the Gyro Sensor. We took the advantages by using the combination of Gyro and Tilt sensors. Moreover, we also solved the consumption issue of the whole system. Through various experimentations with usage of ZigBee sensor module, the power consumption for the balancing system is reduced significantly.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.649-655
• /
• 2020

This study determined effective educational strategies by investigating and analyzing the related educational demands for SMEs (small and medium-sized enterprises) in the 4th Industrial Revolution based area of smart farms. In order to derive the approprate educational strategies, Importance-Performance Analysis (IPA) and Borich's Needs Assessment Model were conducted based on the smart farm technological field. As a result, the education demand survey showed high demand for production systems and intelligent farm machinery. In detail, Borich's analysis showed the need for pest prevention and diagnosis technology (8.03), network and analysis SW linkage technology (7.83), and intelligent farm worker-agricultural power system-electric energy hybrid technology (7.43). In contrast, smart plant factories (4.09), lighting technology for growth control (4.46) and structure construction technology (4.62) showed low demands. Based on this, the IPA portfolio shows that the network and analysis SW linkage technology and the CAN-based complex center are urgently needed. However, the technology that has already been developed, such as smart factory platform development, growth control lighting technology and structure construction technology, was oversized. Based on these results, it is possible to strategically suggest the customized training programs for industrial sectors of SMEs that reflect the needs for efficiently operating smart farms. This study also provides effective ways to operate the relevant training programs.

• Journal of Periodontal and Implant Science
• /
• v.27 no.4
• /
• pp.819-828
• /
• 1997

The purpose of this study was to evaluate the abrasion-resistance of root surface after NaF iontophoresis, Nd:YAG laser irradiation and combined treatment 50 anterior teeth with flat interproximal root surface that had been extracted due to periodontal destruction were selected. All teeth were treated by the same procedure as conventional periodontal root treatment, such as scaling and root planing, root conditioning with tetracycline HCI(lOOmg/ml, 5min). The pre-treatment weight of each tooth was measured by a dial scale(SHIMADEU Co, LIBROR EB-220HU, capacity 220.000 g, Japan). All teeth were divided into 5 groups as follows: Nd:YAG laser irradiation(group 1, 1 W, 100 mJ, 10Hz, fiberoptic-root surface distance=5mm, $10\;sec.{\times}6times$, EL.EN.EN060, Italy): NaF iontophoresis(group 2, $150{\mu}A$, 4 min}: Nd:YAG laser irradiation following NaF iontophoresis(group 3): NaF iontophoresis following Nd:YAG laser irradiation(group 4): No treatment(control group). Electric toothbrushing (Oral-B, Brown Co, Germany) was conducted during 1 hour($lO\;min.{\times}6\;times$). Subsequently post-treatment weight was remeasured by the same method as pre-treatment weight measurement. The difference of abrasion rate among all groups was statistically analyzed by ANOVA(SAS program). Following results were obtained: 1. The abrasion rate was significantly lower in Nd:YAG laser irradiation group than NaF iontophoresis group(p < 0.001). 2. The abrasion rate was significantly lower in combined groups of Nd:YAG laser irradiation and NaF iontophoresis than either Nd:YAG laser irradiation group or NaF iontophoresis group(p < 0.001). 3. There was no significant difference in abrasion rate according to application order in the combined groups(p > 0.05). 4. The abrasion rate was significantly lower in all experimental groups than control group(p < 0.001). The results suggest that combined treatment of Nd:YAG laser irradiation and NaF iontophoresis on exposed root surface after periodontal therapy can enhance the abrasion-resistance of root surface and may inhibit the root caries development.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.3
• /
• pp.479-485
• /
• 2006

The double gate(DG) MOSFET is a promising candidate to further extend the CMOS scaling and provide better control of short channel effect(SCE). DGMOSFETs, having ultra thin undoped Si channel for SCEs control, ale being validated for sub-20nm scaling. A novel analytical transport model for the subthreshold mode of DGMOSFETs is proposed in this paper. The model enables analysis of short channel effect such as the subthreshold swing(SS), the threshold voltage roil-off$({\Delta}V_{th})$ and the drain induced barrier lowering(DIBL). The proposed model includes the effects of thermionic emission and quantum tunneling of carriers through the source-drain barrier. An approximative solution of the 2D Poisson equation is used for the distribution of electric potential, and Wentzel-Kramers-Brillouin approximation is used for the tunneling probability. The new model is used to investigate the subthreshold characteristics of a double gate MOSFET having the gate length in the nanometer range $(5-20{\sim}nm)$ with ultra thin gate oxide and channel thickness. The model is verified by comparing the subthreshold swing and the threshold voltage roll-off with 2D numerical simulations. The proposed model is used to design contours for gate length, channel thickness, and gate oxide thickness.