• 비파괴검사학회지
• /
• 제37권2호
• /
• pp.115-121
• /
• 2017

The nonlinear ultrasonic technique is a potential nondestructive method to evaluate material degradation, in which the ultrasonic nonlinearity parameter is usually measured. The ultrasonic nonlinearity parameter is defined by the elastic nonlinearity coefficients of the nonlinear Hooke's equation. Therefore, even though the ultrasonic nonlinearity parameter is not equal to the elastic nonlinearity parameter, they have a close relationship. However, there has been no experimental verification of the relationship between the ultrasonic and elastic nonlinearity parameters. In this study, the relationship is experimentally verified for a heat-treated aluminum alloy. Specimens of the aluminum alloy were heat-treated at $300^{\circ}C$ for different periods of time (0, 1, 2, 5, 10, 20, and 50 h). The relative ultrasonic nonlinearity parameter of each specimen was then measured, and the elastic nonlinearity parameter was determined by fitting the stress-strain curve obtained from a tensile test to the 5th-order-polynomial nonlinear Hooke's equation. The results showed that the variations in these parameters were in good agreement with each other.

• 항공우주기술
• /
• 제9권2호
• /
• pp.73-79
• /
• 2010

본 연구에서는 비선형 유한요소 해석을 수행하여 굴곡도에 따른 유연직물복합재료의 등가 탄성계수를 예측하였다. 해석은 상용 유한요소 해석 프로그램인 ABAQUS를 사용하여 수행되었다. 해석에서는 섬유다발의 재료적 비선형성과 대변형 시 발생하는 기하학적 비선형성이 고려되었으며, 섬유다발의 대 전단 변형으로 발생하는 기하학적 비선형성을 고려하기 위하여 사용자 부프로그램을 작성하여 이를 ABAQUS내에 삽입하였다. 결과에서는 일축하중 상태에 있는 유연직물복합재료의 응력-변형률 거동을 예측하여 이로부터 계산된 등가탄성계수를 시험결과와 비교하였으며, 다양한 섬유 굴곡도를 갖는 유연직물복합재료에 대한 등가탄성계수를 계산하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.933-943
• /
• 2009

Axial loads and shaft resistances can be calculated by load transfer analysis using strain data with load level. In load transfer analysis, the elastic modulus of concrete is a one of the most important parameters to consider. The elastic modulus, $E_{50}$, suggested by ACI (American Concrete Institute), has been commonly used. However, elastic modulus of concrete shows nonlinear stress-strain characteristic, so nonlinearity should be considered in load transfer analysis. In this paper, a load transfer analysis was performed by using data obtained from bi-directional pile load tests for four cases of drilled shafts. For consideration of nonlinearity, elastic modulus was calculated by both the Fellenius method and the nonlinear method, assuming the stress-strain relation of concrete to be a quadratic function, and then, the calculated elastic modulus was applied to the estimation of shaft resistance. The calculated shaft resistances were compared with the result obtained using the constant elastic modulus of ACI code. It was found that the f-w curves are similar to each method, and elastic modulus and shaft resistances decreased as strain increased. Moreover, shaft resistances estimated from elastic modulus considering nonlinearity were 5~15% different than those obtained using the constant elastic modulus.

• Computers and Concrete
• /
• 제19권1호
• /
• pp.1-6
• /
• 2017

Prestressed concrete I-girders are subject to different load types at their construction stages. At the time of strand release, i.e., detensioning, prestressed concrete girders are under the effect of dead and prestressing loads. At this stage, the camber, total net upward deflection, of prestressed girder is summation of the upward deflection due to the prestressing force and the downward deflection due to dead loads. For the calculation of the upward deflection, it is generally considered that prestressed concrete I-girder behaves linear-elastic. However, the field measurements on total net upward deflection of prestressed I-girder after detensioning show contradictory results. In this paper, camber calculations with the linear-elastic beam and elastic-stability theories are presented. One of a typical precast I-girder with 120 cm height and 31.5 m effective span length is selected as a case study. 3D finite element model (FEM) of the girder is developed by SAP2000 software, and the deflections of girder are obtained from linear and nonlinear-static analyses. Only geometric nonlinearity is taken into account. The material test and field measurement of this study are performed at prestressing girder plant. The results of the linear-elastic beam and elastic-stability theories are compared with FEM results and field measurements. It is seen that the camber predicted by elastic-stability theory gives acceptable results than the linear-elastic beam theory while strand releasing.

• Structural Engineering and Mechanics
• /
• 제67권1호
• /
• pp.53-67
• /
• 2018

The changes of parameters of pressure and velocity of propagation of elastic pressure and shear waves in uniformly deformed solid compressible media are studied within the nonclassically linearized approach (NLA) of nonlinear elastodynamics to create a new theoretical basis of the geomechanical interpretation of various groups of geophysical observational and experimental data. The cases of small and large deformations are considered while their describing by various elastic potentials, i.e., problems considering the physical and geometric nonlinearity. Convenient analytical formulae are obtained to calculate the indicated parameters in the deformed isotropic media within the nonclassical linear and nonlinear solution in the NLA. Specific numerical experiments are conducted in case of overall compression of various materials. It is shown that the method (generally accepted in the studies of mechanics of standard constructional materials) of additional linearization (relative to the pressure parameter) in the basic correlations of the NLA introduces substantial quantitative and qualitative errors into the results at significant preliminary deformations. The influences of the physical and geometric nonlinearity on the studied characteristics of the medium are large in various materials and differ qualitatively. The contribution of nonlinear components to the values of the considered parameters prevails over linear components at large deformations. When certain critical values of compression deformations in the medium are achieved, elastic waves with actual velocity cannot propagate in it. The values of the critical deformations for pressure and shear waves differ within different elastic potentials and variants of the theory of initial deformations.

• 신재생에너지
• /
• 제7권4호
• /
• pp.50-57
• /
• 2011

A wind turbine simulation program for the coupled dynamics of aerodynamics, elasticity, multi-body dynamics and controls of turbine is newly developed by combining an aero-elastic code and a multi-body dynamics code. The aero-elastic code, based on the blade momentum theory and generalized dynamic wake theory, is developed by NREL(National Renewable Energy Laboratory, USA). The multi-body dynamics code is commercial one which is capable of accounting for geometric nonlinearity and twist deflection. A turbulent wind load case is simulated for the NREL 5-MW baseline wind turbine model by the developed program and FAST. As a result, the two results agree well enough to verify the reliability of the developed program.

• 대한기계학회논문집A
• /
• 제35권6호
• /
• pp.651-659
• /
• 2011

최근 열출력이 향상된 신규 원자력발전소의 개발이 증가하고 있으며 배관계에 가해지는 모멘트 및 하중의 크기도 증가하는 경향이므로 배관의 파단전누설(LBB) 적용조건 여유도가 작아질 수 있다. 본 논문에서는 이러한 배관에서 LBB 적용조건을 만족시키기 위한 추가적인 여유도 확보의 한 방법으로써 균열의 비선형과 재료물성치를 고려하는 방법을 제시하였다. 균열 및 재료의 비선형을 고려하기 위하여 유한요소해석과 보(beam) 이론을 병용하였다. 원자력 배관을 모델로 하여 본 논문에서 제안한 방법으로 LBB 균열안정성 해석을 수행하였으며, LBB 여유도가 낮은 위치에서 균열 및 재료 비선형을 고려함으로 써 추가적인 LBB 여유도를 확보할 수 있음을 확인하였다.

• Structural Engineering and Mechanics
• /
• 제10권5호
• /
• pp.491-504
• /
• 2000

This paper is a presentation of a physical model for the elastic-partly plastic behavior of rectangular hollow section pinned struts subjected to static cyclic axial loading and the evaluation of the compressive strength of retrofitted damaged struts. Retrofitting is achieved by welding stiffening plates along the webs of damaged struts. The shape of the elastic and permanent deformations of the strut axis satisfy the conditions at the ends and midspan. Continuous functions of the geometric variables of stress distributions in the yielded zone are evaluated by interpolation between three points along each partly plastic zone. Permanent deformations of the partly plastic region are computed and used to update the shape of the unloaded strut. The necessity of considering geometric nonlinearity is discussed. The sensitivity of the results to the location of interpolation points, the shape of the permanent deformation and material hysteretic properties is investigated.

• Computers and Concrete
• /
• 제20권4호
• /
• pp.503-509
• /
• 2017

In this study, fire-damaged concrete was investigated by a nonlinear resonance vibration (NRV) technique, in order to evaluate its residual material properties. For the experiments, five cubic concrete specimens were prepared and four of them were damaged at different temperatures using a furnace. With a thermal insulator wrapped at the sides of specimen, thermal gradation was applied to the samples. According to the peak temperatures and depths of the samples, nonlinearity parameters were calculated with the NRV technique before the tendency of the parameters was evaluated. In addition, compressive strength and dynamic elastic modulus were measured for each sample and a comparison with the nonlinearity parameter was carried out. Through the experimental results, the possibility of the NRV technique as a method for evaluating residual material properties was evaluated.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1993년도 봄 학술발표회논문집
• /
• pp.53-60
• /
• 1993

Nonlinear equation of motion due to material nonlinearity of structure is transformed to linear equation of motion by treating the nonlinear elastic force term as an applied force. The solution in a time step is carried out by iterative linear dynamic analysis. The present simple algorithm is varidated by several examples .The results show that this algorithm is and efficient.