• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.800-806
• /
• 2011

Thermal expansion which occurs at the high speed rail joint is proportional to the free length from the point of fixity. This thermal expansion behaves similar to free expansion because the girder longitudinal stiffness is much larger than longitudinal resistance of rail pads. But the longitudinal displacement in the long rail is nominal because the longitudinal support condition of the girder is normally MFM(movable-fix-movable) system. Due to these girder expansion characteristics, there is longitudinal relative displacement at the rail pad and rail fastener spring which connects rail and girder. If the relative displacement between rail and girder is beyond the elastic limit for the rail pad, rail fastener system shall be applied using sliding fastener to prevent rail pad damage and fastener separation resulting from slip. On the other hand, train vertical vibration and tilting can occur due to the lack of fastener vertical force if the sliding fastener is applied at the girder joint. In the high speed rail bridge, vibration can occur due to the spring stiffness of the elastomeric bearing, also both vertical downward and upward displacement can occur. The elastomeric bearing vertical movement can cause rail displacement and finally the stability of the ballast is reduced because the gravel movement is induced.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.2
• /
• pp.60-68
• /
• 2017

This study was made to examine the motion characteristics according to the reinforcement of the reinforcement length and stiffener reinforcement for shear reinforcement to the foundation structure reinforced with shear reinforcement steel plate. Experimental study was made after specimen was installed on the ground as the same as in the practical site. Reinforcement lengths of the steel for shear reinforcement are divided into 1,000 mm, 1,200 mm and 1,400 mm in the specimen and as for reinforcement method of the stiffener, 4 stiffeners with interval of 100mm reinforced with the same materials as the shear reinforcement were manufactured for the experiment. Considering result of the experiment, it is expressed that no effect of the stiffener reinforcement was found and regarding the reinforcement length of shear reinforcement material the crossed point of the two converted lines of the value that the shear force is expressed in the bearing power in the expanded dangerous section and the value that the shear capacity receivable by the reinforcement materials in the dangerous section is proposed as effective reinforcement length.

• Journal of Ginseng Research
• /
• v.3 no.2
• /
• pp.105-112
• /
• 1979

Effect of gibberllin on the breaking of bud dormancy of root and growth of aerial parts were investigated under laboratory and field condition for the prolongation of shoot growth duration, shortening of fruit bearing age and the increase of root yield. Drop application of GA (0.5ml of 50ppm) on rhizome of one year old root broke bud dormancy better than by low temperature. Soaking for one hour of one year old roots which wintered in the field in GA (50-200ppm) greatly accelerated the emergence of new buds while kinetin was only effective at low level (50ppm). GA substantially increased stem length in early stage and petiole length later on while kinetin increased stem diameter. Under the field condition with polythylene film tunnel (PET) in early spring the soaking in GA (50ppm for 1 hour) of rhizome of 4 year old root with replanting and dropping GA (50ppm, 1ml) on rhizome without replanting brought earlier emergence (29days) in comparison with that in the usual field. PET alone caused 14 day-early emergence. GA increased the length of stem and petiole only in early stage and replanting decreased only petiole length in later stage. Soaking in GA with replanting caused the Pronounced decrease in peduncle length, percentage of (ruin set and dry weight of reproductive organ (fruits and peduncle). Dropping without replanting showed significant decrease only in dry weight of reproductive organ. Fruit maturing was 20 days earlier than in usual held with little difference between GA and PET. It is well expected that GA could be used for early emergence of bud, shortening of root dormancy period, thinning of fruit and higher root yield according to application amount and methods.

• Structural Engineering and Mechanics
• /
• v.61 no.5
• /
• pp.675-684
• /
• 2017

In this paper, a hybrid seismic response control (HSRC) system was developed to control bridge behavior caused by the seismic load. It was aimed at optimum vibration control, composed of a rubber bearing of passive type and MR-damper of semi-active type. Its mathematical modeling was driven and applied to a bridge model so as to prove its validity. The bridge model was built for the experiment, a two-span bridge of 8.3 meters in length with the HSRC system put up on it. Then, inflicting the EI Centro seismic load on it, shaking table tests were carried out to confirm the system's validity. The experiments were conducted under the basic structure state (without an MR-damper applied) first, and then under the state with an MR-damper applied. It was also done under the basic structure state with a reinforced rubber bearing applied, then the passive on/off state of the HSRC system, and finally the semi-active state where the control algorithm was applied to the system. From the experiments, it was observed that pounding rather increased when the MR-damper alone was applied, and also that the application of the HSRC system effectively prevented it from occurring. That is, the experiments showed that the system successfully mitigated structural behavior by 70% against the basic structure state, and, further, when control algorithm is applied for the operation of the MR-damper, relative displacement was found to be effectively mitigated by 80%. As a result, the HSRC system was proven to be effective in mitigating responses of the two-span bridge under seismic load.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.6
• /
• pp.29-38
• /
• 2010

Micro-piles have been used to increase the bearing capacity or to restrain settlement of existing shallow foundation. Recently, micro-piles are used to support the shallow foundation, to stabilize the slope and to resist the sliding of retaining wall. Using the micro-piles in geotechnical engineering, some investigators have studied the effective installing method by model test or field test. But most of previous studies are chiefly focused on the micro-piles in sand or clay layer. If a rock layer exists in soil, the installing length of micro-piles may be determined by the depth of rock layer. In this case, the stiffness of pile may be changed by the installing length of pile, and so the installing method has to be altered by the changed stiffness of pile. Model tests have been conducted to study the installation method of micro-pile in soil with rock layer. As a result, when the ratio of length of pile is below 50 ($L/d{\leq}50$), installing of micro-piles in vertical position is effective regardless of the depth of rock layer. If the depth of rock layer is deeper than soil failure zone and the ratio of the length of pile exceeds 50 (L/d>50), installing of the micro-piles in sloped position is effective.

• Geomechanics and Engineering
• /
• v.14 no.3
• /
• pp.233-240
• /
• 2018

Pullout tests are usually employed to determine the ultimate bearing capacity of reinforced soil, and the load-displacement curve can be obtained easily. This paper presents an analytical solution for predicting the full-range mechanical behavior of a buried planar reinforcement subjected to pullout based on a bi-linear bond-slip model. The full-range behavior consists of three consecutive stages: elastic stage, elastic-plastic stage and debonding stage. For each stage, closed-form solutions for the load-displacement relationship, the interfacial slip distribution, the interfacial shear stress distribution and the axial stress distribution along the planar reinforcement were derived. The ultimate load and the effective bond length were also obtained. Then the analytical model was calibrated and validated against three pullout experimental tests. The predicted load-displacement curves as well as the internal displacement distribution are in closed agreement with test results. Moreover, a parametric study on the effect of anchorage length, reinforcement axial stiffness, interfacial shear stiffness and interfacial shear strength is also presented, providing insights into the pullout behaviour of planar reinforcements of MSE structures.

• Structural Engineering and Mechanics
• /
• v.5 no.6
• /
• pp.803-815
• /
• 1997

It is well understood that concentrated forces applied in the plane of a beam or panel (such as a wall or slab) lead to splitting forces developing within a disturbed region forming beyond the bearing zone. In a linearly elastic material the length of the disturbed region is approximately equal to the depth of the member. In concrete structures, however, the length of the disturbed region is a function of the orthotropic properties of the concrete-steel composite. In the detailing of steel reinforcement within the disturbed regions two limit states must be satisfied; strength and serviceability (in this case the serviceability requirement being acceptable crack widths). If the design requires large redistribution of stresses, the member may perform poorly at service and/or overload. In this paper the results of a plane stress finite element investigation of concentrated loads on reinforced concrete panels are presented. Two cases are examined (i) panels loaded concentrically, and (ii) panels loaded eccentrically. The numerical investigation suggests that the bursting force distribution is substantially different from that calculated using elastic design methods currently used in some codes of practice. The optimum solution for a uniformly reinforced bursting region was found to be with the reinforcement distributed from approximately 0.2 times the effective depth of the member ($0.2D_e$) to between $1.2D_e$ and $1.6D_e$. Strut and tie models based on the finite element analyses are proposed herein.

• Journal of Korean Society of Forest Science
• /
• v.100 no.3
• /
• pp.432-440
• /
• 2011

The objective of this study was to investigate growth and fruiting characteristics (e.g., nut qualities) of chestnut (Castanea cerenata) after applying various fertilizer treatments at the cultivation site in Suncheon. Fertilizer treatments were designed as follow: liquid fertilizer, chemical fertilizer, organic fertilizer, and control. Both liquid and chemical fertilizer treatments provided the best growth in height and basal diameter. In addition, these two treatments were very effective for crown width of the trees between both east-west and north-south orientation. The liquid fertilizer treatment was effective on total length of the fruiting branch and length of the bearing to terminate part. Both liquid and chemical fertilizer treatments produced the longest length of basal to bearing part compared to the other two treatments. The liquid fertilizer treatment showed the most thickened basal diameter of the fruiting branch and the greatest diameter of above and below the bearing burr part. Elongation Index of the fruiting branch (EI) was the highest with liquid fertilizer treatment and the remaining four indices (Production Index of fruiting branch, PI; Ratio of Diameter between below and above bearing burr part, RD; Growth Index of fruiting branch diameter, GI; Thickness Index of fruiting branch or dormant branch, TI) were the highest with the chemical fertilizer treatment. Total number of produced branch per fruiting mother branch and number of small and weak branches per fruiting mother branch were highest on the control and liquid fertilizer treatment; however, all treatments produced similar numbers. The chemical and organic fertilizer treatments produced a high number of fruiting branches per fruiting mother branch, while organic and liquid fertilizer treatments produced a high number of burr per fruiting branch. The rate of commercializing on the basis of nut weight and quantity was higher on control (87.5%) than chemical fertilizer treatment (84.6%); however, the rate was even lower on liquid fertilizer treatment (84.3%) and organic fertilizer treatment (82.7%). The liquid fertilizer treatment showed the highest average of nut weight, while chemical fertilizer treatment showed the highest average number of fruiting burr. There was no significant difference in average number of normal nuts per burr among treatments. The yield per tree was high on chemical (8.2 kg) and liquid (8.0 kg) fertilizer treatments, but there was no significant difference among treatments. In the rate of nut grade on the basis of nut weight and quantity, the liquid fertilizer treatment, 43.5% and 34.3% more than large nut respectively, produced higher value chestnuts compared to other treatments.

• Journal of Korean Society of Steel Construction
• /
• v.27 no.3
• /
• pp.347-357
• /
• 2015

In this study, an experimental study was performed to evaluate the concrete breakout strength of unreinforced cast-in-place anchors by seismic qualification test under shear loading. The CIP anchors tested herein were 30mm in diameter with an edge distance of 150mm and an embedment depth of 240mm in uncracked and cracked concrete. The cracked specimen consisted of orthogonal and parallel crack to the loading direction, respectively. The dynamic loading sequence during the seismic qualification test was determined based on CSA N287.2, ACI 355.2 and ETAG 001 codes. After the dynamic loading, the static loading was applied until failure occurs. The shear resistance by seismic qualification tests showed almost the same strength as that obtained from the static tests in uncrcaked and cracked concrete, respectively. Meanwhile, the breakout depth did not reach $8d_0$, therefore the modified strength equation of ACI 318-11 could estimate properly the concrete breakout strength, which does not consider effective bearing length.

• KIEAE Journal
• /
• v.8 no.3
• /
• pp.77-83
• /
• 2008

The effective mixture of structural laminated timber and other materials is expected to extend the potentials of building structures because of the potentials to realize high performance in structural safety. The classical joint types using drift pin and bolts are occurred local failures due to the small bearing area. In result, new joints using H shaped steel were suggested in this research. The objective of this study is to evaluate elasto-plastic behaviors by strengthening types of wood frames with new joints connecting structural laminated timber with H shaped steel. A total of five specimens of about one-second scale were tested. Specimens had columns with 1,050 height and $84mm{\times}100mm$ section, and a beams with 1,950mm length and $130mm{\times}100mm$ section. Also, the specimens were stiffened by brace, hwang-toh brick, and autoclaved lightweight concrete. The results of the test showed that the specimen stiffened with autoclaved lightweight concrete was characterized by fairly good strength and stiffness than those of the other specimens. Initial stiffness of H-2.0D-NS specimen with 2 times inserting length of beam height showed 1.33 times than that of H-1.5D-NS specimen. However, the strength of H-2.0D-NS specimen has not improved too much than H-1.5D-NS specimen.