• Progress in Superconductivity and Cryogenics
• /
• v.8 no.3
• /
• pp.13-17
• /
• 2006

The effect of the addition of the nano size $Y_2O_3$ powder on the microstructurte and superconducting properties of YBCO thin film deposited on LAO single crystalline substrate by TFA-MOD method was studied. Nano size $Y_2O_3$ powder was added to the stoichiometric precursor solution with a cation ratio of Y : Ba . Cu = 1 : 2 : 3 prepared using TFA as chelating agent. Precursor solutions with and without $Y_2O_3$ addition were coated on $LaAlO_3(100)$ single crystalline substrates by dip coating method. Calcination and conversion heat treatments were performed in controlled atmosphere containing moisture Current carrying capacity(Jc) of YBCO film was enhanced about 50% by $Y_2O_3$ doping and it is thought to be due to the better connectivity of YBCO grains and/or the flux pinning by the $Y_2O_3$ particles embedded in YBCO grains.

• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.568-574
• /
• 1997

The effect of microencapsulation of maetal hydride (MH) with copper on the electrode performance of a Ni/MH battery has been investigated. The MH electrodes were prepared with a combination of cold press and paste methods. The discharge capacity of the electrode increased with an addition of small amounts if CMC into the electrode, but decreased when heat-treated in an oxygen-free nitrogen flow. The capacity of a Cu-coated $LaNi_5$ electrode was higher than that of LaNi5electrode. The discharge capacity of the electrode prepared with Cu-coated $LaNi_5$ increased with the increase of copper content in the electrode. It is considered that the increase of copper content enhanced the current density on the electrode surface, leading to the increase of the discharge capacity The MH electrode coated by an acidic electroless plating method showed much higher discharge capacity than that using an alkaline electroless plating method. The discharge capacity of the $LaNi_{4.5}Al_{0.5}$ electrode was higher than that of the $LaNi_5$ electrode. Also, the effect of microencapsulation on the deactivation of $LaNi_5$ was studied using an absorption-desorption cycle in CO-containing hydrogen.

• Journal of the Korean Chemical Society
• /
• v.32 no.1
• /
• pp.22-29
• /
• 1988

The reaction of methanol-water mixture to $CO_2$ and $H_2$ on alkaline earth metal-copper-zinc oxide has been studied in the temperature range of 150 ${\sim}\;300^{\circ}C$. Generally the addition of the alkaline earth metal to Cu/ZnO resulted in an enhancement of selectivity for $CO_2$ formation and a reduction of catalytic activity. Measurable activities were found from 150$^{\circ}C$, 200$^{\circ}C$, and 250$^{\circ}C$ on Mg/Cu/ZnO, Ca/Cu/ZnO, and Ba/Cu/ZnO respectively. However, the highest selectivity for $CO_2$ formation was observed in Ba/Cu/ZnO catalyst at 250$^{\circ}C$. The effect of alkaline earth metal or ZnO on the reactivity was investigated using temperature programmed desorption of $CO_2$ or temperature programmed reduction with $H_2$ over catalysts respectively. It was found that $CO_2$ interacts more strongly in the sequence of MgO < CaO < BaO and ZnO decereases the reduction temperature of CuO. From the results, it was suggested that ZnO activates $H_2$ in the redox process of Cu component and alkaline earth metals adsorbs $CO_2$ in the catalytic process.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.516-520
• /
• 2011

Sodium borohydride, $NaBH_4$, shows a number of advantages as hydrogen source for portable proton exchange membrane fuel cells (PEMFCs). The hydrogen yield of sodium borohydride hydrolysis reaction was studied. The effect of temperature, $NaBH_4$ concentration, NaOH concentration and catalyst type on the hydrogen yield from $NaBH_4$ hydrolysis reaction were measured. The catalysts of Co-P/Cu, Co-B/Cu and Co-P-B/Cu were used in this study and there was no different effect of these catalysts on the hydrogen yield from $NaBH_4$. Under the temperature of $60^{\circ}C$, the hydrogen yield decreased as $NaBH_4$ concentration increased due to formation of gel with by-products and reactants. The gel formed during $NaBH_4$ hydrolysis reaction diminished the hydrogen evolution rate and total volume of hydrogen. Addition of NaOH stabilizer enhanced the formation of gel and then decreased the hydrogen yield.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.35 no.2
• /
• pp.218-229
• /
• 2011

Dyeing properties of cotton and ramie fabrics with pine needles colorants were studied by investigating the analysis of pine needles colorants, the effect of dyeing conditions (such as dye concentration, dyeing temperatures and times on dye uptakes), effect of mordants, and color change. The various colorfastness of dyed fabrics were evaluated for practical use; in addition, the antimicrobial ability, ultraviolet-cut ability, and deodorant ability were estimated. In the UV-Visible spectrum, the wavelength of the maximum absorption for pine needles extract was 285nm, and pine needles colorants produced a yellow color. From FT-IR and GC-MS results, it was assumed that chromophoric substance from pine needles extracts were mixed with flavonol tannin and flavanol tannin. An increased dyeing concentration resulted in a larger dye uptake and a Freundlich absorption isotherm was obtained. A larger dye uptake occurred as the dyeing time and temperature increased. Post-mordanting was more effective than pre-mordanting and the dye uptake of fabrics improved by mordanting. The colorfastness of dyed fabrics showed a low rating; however, colorfastness to washing and dry cleaning of cotton fabrics mordanted with N.Cu, and friction fastness of ramie fabric mordanted with Cu improved. The dyed fabrics showed very good antimicrobial abilities of 99.9%. In addition, the ultraviolet-cut ability and deodorant ability improved in fabrics dyed with pine needles extracts.

• Transactions of Materials Processing
• /
• v.28 no.1
• /
• pp.34-42
• /
• 2019

In this study, various alloying elements (Cr, Sr, Ca, Cd) were added to improve the mechanical properties of ADC12 fabricated by a die casting process. The effect of alloying elements on the microstructure and mechanical properties were investigated. The phase analysis results of the modified ADC12 alloy with conventional ADC12 alloy, showed the similar characteristics of Al matrix, Si phase, $CuAl_2$ phase and the Fe intermetallic phase. As a result of the microstructure observation, the secondary dendrite arm spacing (SDAS) was shown to have decreased after the addition of the alloying elements. The eutectic Si phase, which existed as flake form in the conventional ADC12 alloy, was modified finely as a fiber form in the modified ADC12 alloy. It was observed that the $CuAl_2$ phase as the strengthening phase was relatively finely distributed in the modified ADC12 alloy. The Fe intermetallic appeared as a Chinese script shaped $Al_6$ (Mn,Fe) which is detrimental to mechanical properties in conventional ADC12 alloy. On the other hand, in the modified ADC12 alloy, polyhedral ${\alpha}-Al_{15}Si_2$ $(Fe,Mn,Cr)_3$ was observed. The tensile properties were improved in the modified ADC12 alloy. The yield strength and tensile strength increased by 12.4% and 10.0%, respectively, in the modified ADC12 alloy, and the elongation was also seen to have been increased. As a result of the pin on disk wear test, the wear resistance properties were also improved by up to about 7% in the modified ADC12 alloy. It is noted that the wear deformation microstructures were also observed, and it was found that the fine eutectic Si and strengthening phases greatly improved abrasion resistance.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.5
• /
• pp.233-238
• /
• 2021

The mechanical, anti-tarnishing, and corrosion characteristics of Yuggi (Cu-22wt%Sn) alloy are greatly affected by fraction of constituent phases according to heat treatment method. The Yuggi heat-treated at 750℃ has a β1' phase of 98% or more, which is a high-temperature disordered beta phase, on the other hand, cast Yuggi that Sn is solid-solutioned into Cu consists with α-phase over 60v/o. This difference of constituent phases of Yuggi may cause a difference in dissolution of Cu under antimicrobial test condition. Nonetheless, few studies have been conducted on the effect of fraction of constituent phases and constituent phases in antimicrobial activity. In addition, few studies have also been conducted on the suitable method measuring the antimicrobial activity of Yuggi. Hence, the purpose of this study is to provide an optimum measurement method of antimicrobial activity, and to evaluate quantitatively the effect of constituent phases on antimicrobial activity.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.39 no.2
• /
• pp.287-293
• /
• 2015

This research verifies stainability, super bacteria antibacterial features and antibiotic resistance of Ulmus davidiana var. japonica Nakai (UD) extract in dye cotton cloth. UD was extracted with hot water, the test cloth dyed, and then processed by mordanting treatment using $FeSO_4$ $7H_2O$, $CuSO_4$ $5H_2O$ and $Al_2(SO_4)_3$. The surface color and color fastness of the three kinds (original cloth, the cloth without mordancy and mordant cloth) were measured and the influence of dying of cotton cloth and the mordant method on the genesistasis of Methicillin-resistant Staphylococcus aureus (MRSA), antibiotic resistant bacteria. 1. The surface color of the cotton cloth for dyeing (without and with mordancy) displayed a reddish and yellowish color. Stainability was greatest when the mordant of $FeSO_4$ $7H_2O$ was used. 2. When a mordant was not used for dyeing, the color fastness to washing, perspiration and friction of the contaminated cloth was satisfactory at 4 to 5 grade in general. 3. As for the antibiotic effect to super bacteria, the growth of germ was meaningfully suppressed both on the cloth without and with mordancy compared to the comparison cloth; in addition, the dyeing method with the biggest antibacterial impact was found to be the mordancy with the mordant of $CuSO_4$ $5H_2O$ after dyeing. The results of the experiments that involved dyeing with UD extract showed that cotton cloth processed through mordancy with the mordant of $CuSO_4$ $5H_2O$ had the biggest antibiosis to super bacteria and that processed with the mordant of $FeSO_4$ $7H_2O$ had the greatest stainability.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.382-382
• /
• 2012

CIGS thin films have received great attention as a promising material for solar cells due to their high absorption coefficient, appropriate bandgap, long-term stability, and low cost production. CIGS thin films are deposited by various methods such as co-evaporation, sputtering, spray pyrolysis and electro-deposition. The deposition technique is one of the most important processes in preparing CIGS thin film solar cells. Among these methods, co-evaporation is one of the best technique for obtaining high quality and stoichiometric CIGS films. However, co-evaporation method is known to be unsuitable for commercialization. The sputtering is known to be very effective and feasible process for mass production. In this study, CIGS thin films have prepared by rf magnetron sputtering using a $Cu(In_{1-x}Ga_x)Se_2$ single quaternary target without post deposition selenization. This process has been examined by the effects of deposition parameters on the structural and compositional properties of the films. In addition, we will explore the influences of substrate temperature and additional annealing treatment after deposition on the characteristics of CIGS thin films. The thickness of CIGS films will be measured by Tencor-P1 profiler. The crystalline properties and surface morphology of the films will be analyzed using X-ray diffraction and scanning electron microscopy, respectively. The optical properties of the films will be determined by UV-Visible spectroscopy. Electrical properties of the films will be measured using van der Pauw geometry and Hall effect measurement at room temperature using indium ohmic contacts.

• Progress in Superconductivity and Cryogenics
• /
• v.11 no.2
• /
• pp.7-10
• /
• 2009

Effects of $BaCO_3$ purity on the superconducting properties of top seeded melt growth (TSMG) processed $Y_{1+x}Ba_2Cu_3O_{7-y}$ (Y1+x, x=0.1 and 0.2) superconductors were investigated. $YBa_2Cu_3O_{7-y}$ (Y123) powder prepared using $BaCO_3$ with 99.75% purity and commercially available Y123 powder of 99.9% were used for the fabrication of single Y123 grain superconductors. $T_c$ values of the Y1+x samples prepared using low purity Y123 powder were slightly lower than those of the samples prepared using a high purity powder. In addition to the lower $T_c$, an anomalous peak effect in the intermediate magnetic fields was observed in Y1+x samples prepared using the low purity $BaCO_3$ powder. The slight decrease in $T_c$ and the anomalous peak effect are ascribed to the possible incorporation of a Y123 phase with impurity elements such as strontium and calcium included in the $BaCO_3$powder of 99.7%. The result suggests that the low purity $BaCO_3$ powder of a low price can be used as a raw power for the fabrication of single grain YBCO bulk superconductors.