• Geomechanics and Engineering
• /
• v.15 no.2
• /
• pp.739-744
• /
• 2018

This paper presents the results of numerical modeling studies on the effect of displacements of tunneling in granular soils. Presence of building loads is considered, to find displacement generated at the surface on tunnel. Effect of varying eccentricities of building is simulated, to find influence of building on vertical and horizontal displacement. Studies were carried out in two cases of with and without a geosynthetic layer installed at the bottom of the footing. Results of analysis revealed, the presence of geosynthetic layer under footing, with building placed on centre line, reduced the surface displacements compared to displacement generated without geosynthetic layer. Presence of geosynthetic layer under footing had a dominant effect in reducing displacements in high storey structures. However, when the building was shifted to greater eccentricities from centre line, presence of geosynthetic layer, led to insignificant reduction of displacements on the centre line at the surface.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.323-325
• /
• 1997

Conventionally it is asummed that the microstrip line conductor has a rectangular cross-section. but the additive and substactive processes used to create conductors for PCBs produce a conductor of approximately Trapezoidal cross-section. For wide Strip line, the thickness and edge effect will be small since most of capacitance is parallel plate rather than fringing and we can ignore the cross-section. For narrow strip lines, the edge effect become immportant. So in this paper, we measure the chracteristic impedance of microstripline by Vector Analyzer and simulate the electromagnetic field of microstripline using finite element method with edge angle.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.2
• /
• pp.292-301
• /
• 1994

The resultant cutting force during machining with a worn tool is viewed as a decomposition of the cutting force into a cutting force component related to chip removal from the workpiece and into a component dependent on the contact force between the tool flank's wear land and the workpiece. The shear line method, in which the cutting force is considered proportional to the length of the shear line, is used to calculate the cutting force component for the removal of the chip, while the elastic effect of the workmaterial on the tool is taken into consideration to analyze the effect of tool flank wear. The predicted resultant cutting force, expressed as the sum of both components, is compared to experimental data obtained during wave-on-wave cutting.

• Journal of the Korea Safety Management & Science
• /
• v.12 no.3
• /
• pp.215-221
• /
• 2010

Many researches and projects are actively implemented in the academic world and industrial world in order to increase the productivity through changing utility layout. Effective layout makes the flow of parts and products go on wheels and helps labor forces and utilities to be used efficiently. In this study, we looked at effect on utility layout change through a case of a company making a fuel tank of vehicle in Korea. Due to the layout improvement, this company could have flowshop system on welding line, so the stock in line was decreased, checking the number of stock became easier than before and it was possible to evaluate exact cycle time per unit. Through not only confirming qualitative effect, but also checking quantitative effect such as UPH(Unit per Hour), we obtained the conclusion that the layout improvement increased the productivity.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2010.04a
• /
• pp.5-6
• /
• 2010

Needs for the methodology of segmentation of linear feature according to the shape characteristics of line feature are increasing in cartographic linear generalization. In this study, the line segmentation method using expansible moving window is presented. This method analyzes the generalization effect of line simplification algorithms depend on the line characters of linear feature and extracts the sections which show exclusively low positional error due to a specific algorithm. The description measurements of these segments are calculated and the target line data are segmented based on the measurements. For segmenting the linear feature to a homogeneous section, expansible moving window is applied. This segmentation method is expected to be used in the cartographic map generalization considering the shape characteristics of linear feature.

• Progress in Superconductivity and Cryogenics
• /
• v.4 no.2
• /
• pp.11-15
• /
• 2002

High speed probe for measurement of sin91e flux quantum circuits is comprised of coaxial cables and microstrip lines in order to carry high speed signals without loss. For the impedance matching between coaxial cable and microstrip line, we have determined the dimension of the microstrip line with 50${\Omega}$ impedance by simulation and then have investigated the effect of line width and cross-sectional shape of signal line, dielectric material, thickness of soldering lead at the coaxial-to-microstrip transition Point, and the an91c between dielectric material and end part of the signal line on the characteristics of signal transmission of the microstrip line. From the simulation, we have found that these all parameter's had influenced on the characteristic of signal transmission on the microstrip line and should be reflected in fabricating high speed probe, We have also determined the dimension of coplanar waveguide to fabricate testing sample for performance test of high speed probe.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.5 no.6
• /
• pp.1-6
• /
• 1982

The objective of this thesis to Provide a better insight into the effect of the amount of in-process storage has on the efficiency of production line with variable operation times. It is assumed that the material enters the line at the first work station and is then processed progressively through the line until it exits at the last work station, a finite amount of in-process storage is provided before all but the first work station of the line and the operation time of the work stations are statistically independent and follow exponential distribution. Under the above assumption, optimum allocation model is developed and following two approaches are used : 1) Given the available storage capacity, optimum allocation which minimizes the number of items in the line. 2) Given the available storage capacity, optimum allocation which. maximizes the utilization factor of the line. In a balanced three stage line, the production line efficiency is maximized under both categories when the second in-process storage is larger than the first.

• 한국정보통신설비학회:학술대회논문집
• /
• 2008.08a
• /
• pp.573-578
• /
• 2008

While going through economic development for several decades, Korea has become an industrialized country, and the development of industrial technology accelerated the advent of the information opportunity era. The recent information oriented society has brought forth the development of new information communication technology that enables anybody to obtain information easily and simply, and recently power line communication technology is being developed that allows the use of the existing power line net-works as they are. Each advanced country that faced up to a riffle effect of power line communication technology that enables us to obtain information easily anywhere at anytime is engaged in fierce competition to be a leader in this technology and to preoccupy the standardization of power line communication technology. At this point, this study is to help Korea take the lead in information communication technology by proposing a direction for the standardization that Korean power line communication technology needs to head for by identifying the trend of the worldwide of power line communication technology.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1998.10a
• /
• pp.241-248
• /
• 1998

• Proceedings of the Korean Geotechical Society Conference
• /
• 1997.03a
• /
• pp.103-112
• /
• 1997