• Journal of Welding and Joining
• /
• v.23 no.4
• /
• pp.48-52
• /
• 2005

To estimate welding deformation for large steel structures, either experiment result with small specimen or analysis result of FEM with small numerical model is used. Consequently, it is important to decide the welding length of specimen and numerical model not to have an effect on welding deformation for accurate estimation of whole welding deformation. This study experimentally clarifies the effect of welding length on angular distortion due to welding by varying welding length of specimens, but fixing width and thickness of specimens on V-groove butt welding, fillet welding and bead on plate welding. As a resell the critical welding length on fillet welding and on bead on plate welding is over 500mm and on V-groove butt welding is over 1,000mm.

• Journal of Ginseng Research
• /
• v.19 no.3
• /
• pp.287-290
• /
• 1995

This study was conducted to elucidate the effect of physical properties of soil in nursery bed with different densities on growth of ginseng seedling. Stem length, leaf length and leaf width of ginseng seedling showed the decreasing tendency with increasing the hardness of the nursery soil. Fresh root weight per seedling and number of available seedlings were increased significantly with decrease of the soil hardness. For solid, liquid phases, bulk density and hardness of soil, negative correlations were shown in stem length, leaf length, leaf width, root weight per seeding, and number t of available seedlings. On the other hand, gas phase, air permeability and porosity of soil had positive correlations with stem length, leaf length, leaf width, root weight per seedling and number of available seedlings. Key words Yang-Jik nursery, ginseng seedling, soil physical properties.

• Asian-Australasian Journal of Animal Sciences
• /
• v.9 no.4
• /
• pp.363-370
• /
• 1996

The effect of breeding length of sire on genetic progress was examined in the Holstein dairy cattle population in Japan. Genetic progress was extimated by gene flow method. Breeding length of sires directly influences the replacement rates of sires and the selection intensity of sires because there are a fixed number of progeny tested young bulls per year. As breeding length of sires increased, rate of gene flow decreased and average proportions of genes deriving from selected animals had lower asymptotic values. When breeding length was short, average proportions of genes required a longer period to converge to asymptotic values. Changes of Rcow-sire's(sire to breed recorded cows) and Ncow-sire's(sire to breed non recorded cows) breeding length influenced not only transmission of their genes but also that of genes derived from all other selected animals. Irrespective of whether the discount rate was assumed to be 0 or 6%, longer term (${\geq}$ 20 years) expected total genetic improvement was maximized by a sire breeding length of five years. For shorter term assessment(10 years), genetic improvement was maximized by a sire breeding length of three years. There was a linear increase in the contribution of the sire to bulls pathway to the total genetic improvement, with increase in the term of assessment.

• Structural Engineering and Mechanics
• /
• v.65 no.4
• /
• pp.401-408
• /
• 2018

Concentric braced frames are commonly used in steel structures to withstand lateral forces. One of the drawbacks of these systems is the possibility that the braces are buckled under compressive loads, which leads to sudden reduction of the bearing capacity of the structure. To overcome this deficiency, the idea of the Buckling Restrained Brace (BRB) has been proposed in recent years. The length of a BRB steel core can have a significant effect on its overall behavior, since it directly influences the energy dissipation capability of the member. In this study, numerical methods have been utilized for investigation of the optimum length of BRB steel cores. For this purpose, BRBs with different lengths placed into several two-dimensional framing systems with various heights were considered. Then, the Response History Analysis (RHA) was performed, and finally, the optimum steel core length of BRBs and its effect on the responses of the overall system were investigated. The results show that the shortest length where failure does not occur is the best length that can be proposed as the optimum steel core length of BRBs. This length can be obtained through a formula which has been derived and verified in this study by both analytical and numerical methods.

• Health Policy and Management
• /
• v.28 no.2
• /
• pp.178-185
• /
• 2018

Background: We investigated association between introduction of the diagnosis-related groups (DRG) system for anal operation and length of stay. Also, we investigated how it is different among hospitals with longer length of stay and among hospitals with shorter length of stay before introduction of the DRG system. Methods: We used data from Health Insurance Review and Assessment which were national health insurance claim data. Total 13,111 cases of anal surgery cases were included which were claimed by hospitals since July 2012 to June 2014. Two-level multivariable regression was conducted to analysis the association between length of stay and characteristics of hospital and patient. Results: Before introducing DRGs, the average length of stay was 5.41 days. After introducing DRGs, average length of stay was decreased to 3.92 days. After introducing DRGs, length of stay has decreased (${\beta}=-1.0450$, p<0.0001) and it was statistically significant. Among hospitals which had short length of stay (shorter than mean of length of stay) before introducing DRGs, effect of introducing DRGs was smaller (${\beta}=-0.4282$, p<0.0001). On contrary, among hospitals which had long length of stay (longer than mean of length of stay) before introducing DRGs, effect of introducing DRGs was bigger (${\beta}=-1.8280$, p<0.0001). Conclusion: Introducing DRGs was more effective to hospitals which had long length of stay before introducing DRGs.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.322-325
• /
• 2009

An enhanced continuum model for the size dependent strengthening of particle reinforced composites is presented. The model accounts explicitly for the enhanced strength in a discretely defined "punched zone" around the particle in a metal matrix composite as a result of geometrically necessary dislocations developed through a CTE mismatch. The size of the punched zone presents an intrinsic length scale, and this results in the size dependence of the overall behavior of the composite. Results show that predicted 0.2% offset yield stresses are increasing with smaller inclusions and larger volume fractions and this length-scale effect on the enhanced strength can be observed by explicitly including GND region around the particle.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.3
• /
• pp.59-65
• /
• 1999

This study has been performed to confirm the three dimensional effect of the crack reduction and the restrained effect of crack growth for the synthetic fiber reinforced soil. Two types of polyrpropylene fiber and low plastic clay(CL) were used for the test. And the test variable were fiber length and so on. The results of the study were summarized as follows ; 1) The mixing of synthetic fiber was effective in reducing crack growth due to adhesion between soil partlcles and synthetic fiber.l Especially initlal crack was delayed, as compared with the pure soil, for about 1 day in case of mono filament synthetic fiber and for about 1 or 2 days in case of fibrillated syntetic fiber. 2) As the content and length of synthetic fiber were increased , the effect of crack reduction was increased. It was found that 0.5% fibrillated synthetic fiber with 40mm length reinforced soil had about 3 times more effective than natural soils. 3) In case of the same fiber content and fiber length, the fibrillated synthetic fiber has nmore effective than the mono filament synthetic fiber for crack reduction.

• Journal of Crop Science and Biotechnology
• /
• v.11 no.2
• /
• pp.151-156
• /
• 2008

The objective of this study is to identify main-effect QTLs, epistatic QTLs, and the interactions between QTL and the environment associated with grain appearances of brown rice. A genetic linkage map was created with 172 DNA markers spanning 12 rice chromosomes based on 120 DH lines, which derived from a cross between 'Samgang'(Tongil) and 'Nagdong'(Japonica). One thousandgrain weight, length, width, length-to-width ratio, and thickness were evaluated regarding the DH population. Twenty independent QTLs and fourteen epistatic QTLs were identified in using CIM by two programs, known as WinQTLcart2.5 and QTLMAPPER. The QTLs of qgw9.1 in an interval of RM434-RM242 on chromosome 9 and qgw11.1 at a peak marker of RM287 on chromosome 11 for one thousand-grain weight, qgwi2.2 for grain width at a peak marker of RM450, qlw2.1 for length-to-width ratio flanked by RM492 and RM324, and qgt2.1 for thickness flanked by 2009 and RM492 on chromosome 2 were detected over two years, which can be considered as stable QTLs. The epistatic effect might be an important component for genetic basis of one thousand-grain weight and width. The main-effect QTLs of grain width and length to width ratio were easily influenced by environments.

• Transactions of Materials Processing
• /
• v.15 no.8 s.89
• /
• pp.544-549
• /
• 2006

In this work, we have employed the strain gradient plasticity theory to investigate the effect of material size on the deformation behavior in metal forming process. Flow stress is expressed in terms of strain, strain gradient (spatial derivative of strain) and intrinsic material length. The least square method coupled with strain gradient plasticity was used to calculate the components of strain gradient at each element of material. For demonstrating the size effect, the proposed approach has been applied to plane compression process and micro rolling process. Results show when the characteristic length of the material comes to the intrinsic material length, the effect of strain gradient is noteworthy. For the microcompression, the additional work hardening at higher strain gradient regions results in uniform distribution of strain. In the case of micro-rolling, the strain gradient is remarkable at the exit section where the actual reduction of the rolling finishes and subsequently strong work hardening take places at the section. This results in a considerable increase in rolling force. Rolling force with the strain gradient plasticity considered in analysis increases by 20% compared to that with conventional plasticity theory.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.11
• /
• pp.1185-1191
• /
• 2008

This paper presents an approach to define an optimal piezoactuator length to actively control structural vibration. The optimal ratio of the piezoactuator length against the beam length when a pair of piezoceramic actuator and accelerometer is used to suppress unwanted vibration with direct velocity feedback(DVFB) control strategy is not clearly defined so far. It is well known that DVFB control can be very useful when a pair of sensor and actuator is collocated on structures with a high gain and excellent stability. It is considered that three different collocated Pairs of piezoelectric actuators (20, 50 and 100 mm long) and accelerometers installed on three identical clamped-clamped beams($30{\times}20{\times}1mm$). The response of each sensor-actuator pair requires strictly positive real(SPR) property to apply a high feedback gain. However the length of the piezoactuator affects the SPR property of the sensor-actuator response. Intensive simulation and experiment show the effect of the actuator length variation is strongly related with the frequency range of the SPR property. Thus an optimal length ratio was suggested to obtain relevant performance with a good stability under the DVFB strategy.