• 대한기계학회논문집A
• /
• 제22권4호
• /
• pp.723-730
• /
• 1998

With the introduction of edge drop control system in Tandem Cold Rolling Mill, it is necessary to develop te numerical expression for the set-up and edge drop automatic control of cold rolled sheet. As a first step we developed a simulation program which predicts profile and the amounts of edge drop at the delivery side of each stand by using roll deformation anlysis with the slit roll model. And by using the program the effect of various rolling conditions on edge drop was investigated. As a result the relations were obtained between the amounts of edge drop and rolling conditions. Based on above relations, the numerical expression was developed for the set-up and automatic control of edge drop by multi-regression of simulation results for the variation of edge drop amount with each rolling condition.

• 대한기계학회논문집A
• /
• 제20권4호
• /
• pp.1202-1215
• /
• 1996

In this study, in order to achieve the uniformity of mechanical properties and microstructures of a hot-rolled coil in the transversal direction, the edge mask device is newly device is newly developed and installed at the upper laminar-flow cooling head in the run out table, which controls the transversal temperature of strip with enco panel and bar edge heater. The device that is transversally movable prevents the temperature drop of strip edge by blocking the cooling water into the strip edge. So, the pattern of edge mask set-up condition of the device was derived by analyzing the characteristics of strip temperature and mechanical properties according to the on-line application of edge mask.

• 한국시뮬레이션학회논문지
• /
• 제18권3호
• /
• pp.91-102
• /
• 2009

평균 윈도우 크기는 평균 처리율과 많은 관계를 가지고 있다. 제안된 dropper는 fairness를 향상시키기 위해 윈도우 크기를 각 플로우의 레벨에 맞게 제어하도록 한다. 경쟁 패킷 드랍은 플로우가 많은 양의 대역폭을 차지하기 위해 동작한다. 경쟁 패킷 드랍 때문에 플로우는 전송 속도를 반으로 줄이게 되며, 이에 따라 코어 링크의 여유 용량이 존재하게 된다. 다른 플로우는 이 새로운 용량을 사용하게 되고, 따라서 다른 플로우는 좋은 처리율을 가지게 된다. 이런 방식으로 TCP의 전송속도를 제어하는 edge router의 새로운 기능 block인 TRC Dropper(Transmission Rate Control Dropper)를 제안한다. 제안한 TRC Dropper를 통하여 플로우들 간에 공평한 대역폭 분배를 실현하여 상대적으로 차별화된 서비스를 제공할 수 있다.

• 한국통신학회논문지
• /
• 제31권4B호
• /
• pp.255-269
• /
• 2006

The differentiated services(DiffServ) architecture provides packet level service differentiation through the simple and predefined Per-Hop Behaviors(PHBs). The Assured Forwarding(AF) PHB proposed as the assured services uses the RED-in/out(RIO) approach to ensusre the expected capacity specified by the service profile. However, the AF PHB fails to give good QoS and fairness to the TCP flows. This is because OUT(out- of-profile) packet droppings at the RIO buffer are unfair and sporadic during only network congestion while the TCP's congestion control algorithm works with a different round trip time(RTT). In this paper, we propose an Adaptive Regulating Drop(ARD) marker, as a novel dropping strategy at the ingressive edge router, to improve TCP fairness in assured services without a decrease in the link utilization. To drop packets pertinently, the ARD marker adaptively changes a Temporary Permitted Rate(TPR) for aggregate TCP flows. To reduce the excessive use of greedy TCP flows by notifying droppings of their IN packets constantly to them without a decrease in the link utilization, according to the TPR, the ARD marker performs random early fair remarking and dropping of their excessive IN packets at the aggregate flow level. Thus, the throughput of a TCP flow no more depends on only the sporadic and unfair OUT packet droppings at the RIO buffer in the core router. Then, the ARD marker regulates the packet transmission rate of each TCP flow to the contract rate by increasing TCP fairness, without a decrease in the link utilization.

• 대한기계학회논문집
• /
• 제11권5호
• /
• pp.837-845
• /
• 1987

본 연구에서는 Tozawa의 이와 같은 근사적 3차원 해석법을 검토하여 그 특징 을 살피고 판나비, 판두께, 압하율의 변화가 삼차원변형역과 평면변형역의 최적 경계 면 위치에 미치는 영향을 고찰하고자 한다.

• 한국산학기술학회논문지
• /
• 제18권3호
• /
• pp.115-121
• /
• 2017

도시철도 터널 내에 축적된 미세먼지(PM10 and PM2.5)의 제거를 위해 사용되는 분진흡입차량은 에어 블로어와 흡입시스템으로 구성된 하부흡입시스템의 설계방법에 따라 성능이 달라진다. 본 논문에서는 터널 집진차량의 하부에 설치된 먼지 흡입시스템의 효율 향상을 위하여 흡입구와 에어 블로어에 코안다 효과를 이용한 유속 조절장치를 적용하여 그 효과를 확인하였다. 특히, 공기 유동에 대한 수치해석을 통하여 진공 흡입구 내에 코안다 효과를 이용한 유속조절장치를 적용하였으며, 유속 조절각이 약 90도 내외일 때 유속의 상승과 더불어 유동의 안정화가 동시에 이루어질 수 있음을 확인하였다. 또한 링 블로어에 의해 동작되는 에어 나이프형 공기 블로어는 양쪽 끝 가장자리에 코안다 효과를 유도할 수 있는 엣지 구조를 삽입함으로써 블로어 양 끝단의 유속 저하를 개선할 수 있음을 확인하였다. 이러한 4개의 통합된 모듈 형식의 흡입 시스템의 설계는 최적화를 통하여 바닥 먼지가 비산됨과 동시에 흡입구로 흡입되어 궤도면에 누적된 미세먼지와 초미세먼지의 제거에 효과적으로 활용될 수 있을 것으로 기대된다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.307-316
• /
• 2004

This study examined the cause of the wrinkle defect which is frequently encountered in wire rod rolling of low carbon steel$(C0.08\~0.13wt.\%)$. Even a small defect on the surface of rolled bars can easily develop into fatal cracks during cold heading process of low carbon steel, and it is therefore necessary to minimize inherent defects on the surface of hot rolled bars. Hot rolling process of low carbon steel was analyzed to identify the cause of the wrinkle defect in conjunction with FE analysis. The integrated analysis revealed that the wrinkle defect initiated in the first stage of rolling, and it was at the billet edge where severe deformation and drastic temperature drop were present. To elucidate the micro-mechanical mechanism of the wrinkle defect, hot compression tests were carried out at various temperatures and strain rates using Gleeble-3800. The surface profile of the each other compressed specimens was compared, and rough surface lines were observed at relatively low temperatures. Those surface defects can develop into wrinkles during multi-pass rolling. To control the wrinkle defect in rolling, it is necessary to design an adequate caliber which can minimize the loss of ductility, and thereby prevent flow localization. To use the result of this study fur other steels, the quantitative measure of the wrinkle defect and flow localization parameter should be proposed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.109-118
• /
• 2004

No.2 PCM (Pickling and tandem cold rolling mill) at Pohang works was revamped in 2003. The purpose of this project is to produce carbon and stainless steel using conventional carbon production process, rolling and annealing. This paper introduces the applied facilities and technologies of PCM which are used in production of carbon and stainless steel. To realize the main purpose of this project, POSCO have developed laser weld technology in normal carbon and special steel (stainless, high carbon and high silicon). And this report describes the method which is developed to get down the surface defect of stainless 400 series. After revamping, No.2 PCM can have competitive power in this field and can supply the special steel using carbon rolling process.

• 한국전자파학회논문지
• /
• 제16권5호
• /
• pp.482-487
• /
• 2005

본 연구에서는 distributed amplifer를 구성하는 cascode 단위이득단의 공통게이트의 게이트 단자에 가변 커패시터를 연결함으로써 출력 저항 값을 조절하는 방법을 제안한다. Cascode 이득단은 공통 소스 이득단에 비해 높은 이득, 높은 출력저항, 부성저항을 제공하는 등 여러 장점이 있지만 설계시 사용한 트랜지스터 모델이 부정확하고 공정변수가 달라진다면 이득이 떨어지기 시작하는 band edge에서 발진할 위험이 있다. 그러므로 회로가 제작된 이후에도 발진을 막을 수 있는 조절회로가 필요하게 되는데, cascode단위 이득단의 공통 게이트 단자에 연결된 가변 커패시터가 그 역할을 할 수 있다. 제작한 distributed amplifier를 측정해본 결과 가변 커패시터를 조절함으로써 이득 특성을 변화시킬 수 있었으며, 이는 회로의 안정도를 보장할 수 있음을 알 수 있었다. 49GHz의 밴드폭내에서 이득은 $8.92\pm0.82 dB$이며, 군지연은 41GHz 이내에서 $\pm9.3 psec$ 범위 이내였다. 사용된 모든 transistor는 GaAs 기반의 $0.15{\mu}m$ 게이트 길이를 가지 는 p-HEMT이며, distributed amplifier는 총 4개의 이득단으로 구성되어 있다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2001년도 춘계학술발표회 초록집
• /
• pp.3-3
• /
• 2001

Recently TiN, TiAlN, CrN hardcoatings have adapted many industrial application such as die, mold and cutting tools because of good wear resistant and thermal stability. However, in terms of high speed process, general hard coatings have been limited by oxidation and thermal hardness drop. Especially in the case of PCB drill, high speed cutting and without lubricant process condition have not adapted these coatings until now. Therefore more recently, superhard nanocomposite coating which have superhard and good thermal stability have developed. In previous works, WC-TiAlN new nanocomposite film was investigated by cathodic arc ion plating system. Control of AI concentration, WC-TiAlN multi layer composite coating with controlled microstructure was carried out and provides additional enhancement of mechanical properties as well as oxidation resistance at elevated temperature. It is noted that microhardness ofWC-TiA1N multi layer composite coating increased up to 50 Gpa and got thermal stability about $900^{\circ}C$. In this study WC-TiAlN nanocomposite coating was deposited on PCB drill for enhancement of life time. The parameter was A1 concentration and plasma cleaning time for edge sharpness maintaining. The characteristic of WC-TiAlN film formation and wear behaviors are discussed with data from AlES, XRD, EDS and SEM analysis. Through field test, enhancement of life time for PCB drill was measured.