• Korean journal of applied entomology
• /
• v.51 no.3
• /
• pp.235-243
• /
• 2012

Population dynamics of the American serpentine leafminer, Liriomyza trifolii (Burgess), were observed and modeled in order to compare the effects of air and tomato leaf temperatures inside a greenhouse using DYMEX model builder and simulator (pre-programed module based simulation programs developed by CSIRO, Australia). The DYMEX model simulator consisted of a series of modules with the parameters of temperature dependent development and oviposition models of L. trifolii were incorporated from pre-published data. Leaf surface temperatures of cherry tomato leaves (cv. 'Koko') were monitored according to three tomato plant positions (top, > 1.8 m above the ground level; middle, 0.9 - 1.2 m; bottom, 0.3 - 0.5 m) using an infrared temperature gun. Air temperature was monitored at the same three positions using a self-contained temperature logger. Data sets for the observed air temperature and average leaf surface temperatures were collected (top and bottom surfaces), and incorporated into the DYMEX simulator in order to compare the effects of air and leaf surface temperature on the population dynamics of L. trifolii. The initial population consisted of 50 eggs, which were laid by five female L. trifolii in early June. The number of L. trifolii larvae was counted by visual inspection of the tomato plants in order to verify the performance of DYMEX simulation. The egg, pupa, and adult stage of L. trifolii could not be counted due to its infeasible of visual inspection. A significant positive correlation between the observed and the predicted numbers of larvae was found when the leaf surface temperatures were incorporated into the DYMEX simulation (r = 0.97, p < 0.01), but no significant positive correlation was observed with air temperatures(r = 0.40, p = 0.18). This study demonstrated that the population dynamics of L. trifolii was affected greatly by the leaf temperatures, though to little discernible degree by the air temperatures, and thus the leaf surface temperature should be for a consideration in the management of L. trifolii within cherry tomato greenhouses.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.11
• /
• pp.947-956
• /
• 2009

Residual petroleum hydrocarbons after an oil spill may accumulate in the marine benthic ecosystem due to their high hydrophobicity. A lot of monitoring data are required for the estimation of ecosystem exposure to residual petrochemicals in an ecological risk assessment in the affected region. To save time and cost, the environmental exposure to them in the affected ecosystem can also be assessed using a simple food-web bioaccumulation model. In this study, we evaluated residual concentrations of four selected polycyclic aromatic hydrocarbons (phenanthrene, anthracene, pyrene, and benzo[a]pyrene) in a hypothetic benthic ecosystem composed of six species under two exposure scenarios. Body-residue concentration ranged 5~250 mg/kg body depending on trophic positions in an extreme scenario in which the aqueous concentrations of PAHs were assumed to be one-tenth of their aqueous solubility. In addition, bioconcentration factors (BCFs) and bioaccumulation factors (BAFs) were evaluated for model species. The logarithm of bioconcentration factor (log BCF) linearly increased with increasing the logarithm of 1-octanol-water partition coefficient (log $K_{OW}$) until log $K_{OW}$ of 7.0, followed by a gradual decrease with further increase in log $K_{OW}$ without metabolic degradation. Biomagnification became significant when log $K_{OW}$ of a pollutant exceeded 5.0 in the model ecosystem, indicating that investigation of food-web structure should be critical to predict biomagnifications in the affected ecosystem because log $K_{OW}$ values of many petrochemicals are higher than 5.0. Although further research is required for better site-specific evaluation of exposure, the model simulation can be used to estimate the level of the ecosystem exposure to residual oil contaminants at the screening level.

• KIEAE Journal
• /
• v.8 no.5
• /
• pp.49-54
• /
• 2008

The experimental of temperature, humidity and velocity was taken from the underground pit which utilized the system of ground heat source quite similar to the cool-pit system. Also, through CFD analysis, one could review the effectiveness of analysis of future alternatives. Furthermore, the temperature range of mock up cool-pit system was analyzed by inputting the weather data of annual average soil temperature provided by KMA(Korea Meteorological Administration) into the fluid simulation of anticipated heat distribution. Firstly, the difference between the temperature of air exhaust of the pit or the temperature of air supply of the compressor room and the experimental data for the month of May from the CFD analysis came out to be $0.6^{\circ}C$ and $0.9^{\circ}C$ respectively with tolerance of 3.1% and 4.7%. Secondly, the difference between the temperature of air exhaust of the Pit or the temperature of air supply of the compressor room and the experimental data for the month of July from the CFD analysis came out to be $0.8^{\circ}C$ and $1.1^{\circ}C$ respectively with tolerance of 3.3% and 4.5%. Thirdly, for the month of May, the difference between the experimental data taken for the air exhaust of the Pit or the air supply of the compressor room and soil temperature provided by KMA for monthly and yearly average temperature of Jeonju region came out be $1.9^{\circ}C$ and $1.8^{\circ}C$ respectively with tolerance of 10.7% and 9.8%. Fourthly, for the month of July, the difference between the experimental data taken for the air exhaust of the Pit or the air supply of the compressor room and soil temperature provided by KMA for monthly and yearly average temperature of Jeonju region came out be $1.1^{\circ}C$ and $1.4^{\circ}C$ respectively with tolerance of 4.5% and 5.8%. The result of above experiments allowed us to establish CFD model set up as a verification tool that is based on experimental data collected within the Pit area. Also, one could confirm the possibility to apply weather data of soil temperature provided by KMA in order to anticipate proper value for CFD analysis.

• Explosives and Blasting
• /
• v.27 no.1
• /
• pp.62-78
• /
• 2009

Recently, construction techniques have been rapidly developed with reconstruction of old buildings, urban regeneration and efforts of restoring natural ecology, so demolition of deteriorated buildings has been rapidly increasing. Demolition work of building should be executed without damaging surrounding environments according to relevant regulations. There are various demolition methods and among them, explosives demolition is the most practical way for expenses and safety of work. As a part of Daejeon stream ecological restoration project, this thesis is a case of executing demolition of Chung-Ang Department Store which was built 35 years ago as covered structure on the upper part of Daejeon stream with explosives demolition. This structure is 8 stories high, total height of 41.6 m including basement floor, $1,650m^2$ for building area and $18,351m^2$ for total floor area. It is located in the center of Daejeon city where shopping centers and buildings are crowded and main facilities are Daejeon subway (18m), backside shopping center (20m), underground shopping center(15m), Mokchuk bridge, Eunjung bridge(0.25m) and fiber-optic cable(0.25m). In this project, implosion was selected for explosives demolition methods by considering this area being a busy urban area, and this project was executed after examining collapse movement of structure in advance using simulation program not to damage main facilities. Total 80kg of explosives and 1,000 detonators were being used. This project will be a good case of executing explosives demolition successfully by applying implosion on urban area in the country.

• Journal of Wetlands Research
• /
• v.18 no.3
• /
• pp.324-329
• /
• 2016

Constructed wetlands are widely applied in urban and rural areas for various purposes such as pollutants reduction, acquisition of eco-spaces and habitats, flooding reduction, acquisition of water resources and environmental education. Since the design of constructed wetlands utilizes ecosystems, special consideration must be given to ecological mechanisms, environmental mechanisms and hydrological mechanisms. To ensure the sustainable functionality of constructed wetlands, it is necessary to achieve stable flow rate and velocity, and remove sediments to ensure sufficient space for detention. To enhance the efficiency of constructed wetland sedimentation basins, this study determined the optimal position for baffle installation, and applied Computational Fluid Dynamics (CFD) to the cross-sectional design of wetlands. CFD analysis revealed that the decrease in flow velocity with baffle installation enhanced the efficiency of sedimentation of particulate matters. Vertical baffles had higher sedimentation efficiency than those with an inclined angle. When vertical baffles were installed in the sedimentation basin of a hybrid constructed wetland to reduce non-point source pollutants in urban areas, the average flow velocity within the basin decreased by 10~30%, while the sedimentation efficiency improved by 1.3~1.5 times. The application of CFD to constructed wetlands is expected to improve the cost efficiency of designing hybrid constructed wetlands with high removal efficiency.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.13 no.2 s.29
• /
• pp.103-110
• /
• 2007

This study estirmted the appropriate pollutant load reduction from point sources in Jinhae Bay, Korea, using an eco system model. The results of COD values in the inner part of the bay obtained through the simulation by ecosystem model were greater than 3.0mg/L, and exceeded the limits of Korean Coastal Water Quality Grade III. Engineering countermeasures to reduce the $70\sim90%$ of all land based pollution load or organic and inorganic material loads from point sources by more than 50% were required to keep the COD levels below 2 mg/L. The reduction loads is 5,632kg/day of COD, 481kg/day of DIP and 7,991 kg/day of DIN in case of the reduction of both the organic and nutrients. The estimated environmental currying capacity of that case is 13,112kg/day of COD, 206kg/day of DIP and 3,425kg/day of DIN to keep the COD levels below 2mg/L.

• Journal of the Korean Regional Science Association
• /
• v.38 no.2
• /
• pp.43-57
• /
• 2022

The Land Suitability Assessment is mandatory by National Land Planning and Utilization Act and the results are considered in the establishment of urban master plan and urban management plan. The study aims to examine whether the application of Land Suitability Assessment in developed urban areas is appropriate. A simulation analysis based on the Seoul's data of environmental ecological, physical, and spatial characteristics was conducted on urban green, the only applicable land for the assessment in Seoul. The results of the assessment shows that all pieces of lands in urban green is suitable for 'development'. This conflicts to the purpose of land use of urban green which needs to be conserved to protect the natural environment and landscape, animals and plants, environmental pollution, and urban sprawl. In the analysis applying optional indicators such as the distance from the area of Biotope Class 1 to prevent this conflict, the results shows little difference. This supports the necessity to review this regulation including an option to exclude developed urban areas such as Seoul in the assessment.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.48-48
• /
• 2010

Sound quality and NVH-issues(Noise, Vibration and Harshness) of vehicles has become very important for car manufacturers. It is interpreted as among the most relevant factors regarding perceived product quality, and is important in gaining market advantage. The general sound quality of vehicles was gradually improved over the years. However, today the development cycles in the automotive industry are constantly reduced to meet the customers' demands and to react quickly to market needs. In addition, new drive and fuel concepts, tightened ecological specifications, increase of vehicle classes and increasing diversification(increasing market for niche vehicles), etc. challenge the acoustic engineers trying to develop a pleasant, adequate, harmonious passenger cabin sound. Another aspect concerns the general pressure for reducing emission and fuel consumption, which lead to vehicle weight reductions through material changes also resulting in new noise and vibration conflicts. Furthermore, in the context of alternative powertrains and engine concepts, the new objective is to detect and implement the vehicle sound, tailored to suit the auditory expectations and needs of the target group. New questions must be answered: What are appropriate sounds for hybrid or electric vehicles? How are new vehicle sounds perceived and judged? How can customer-oriented, client-specific target sounds be determined? Which sounds are needed to fulfil the driving task, and so on? Thus, advanced methods and tools are necessary which cope with the increasing complexity of NVH-problems and conflicts and at the same time which cope with the growing expectations regarding the acoustical comfort. Moreover, it is exceedingly important to have already detailed and reliable information about NVH-issues in early design phases to guarantee high quality standards. This requires the use of sophisticated simulation techniques, which allow for the virtual construction and testing of subsystems and/or the whole car in early development stages. The virtual, testing is very important especially with respect to alternative drive concepts(hybrid cars, electric cars, hydrogen fuel cell cars), where complete new NVH-problems and challenges occur which have to be adequately managed right from the beginning. In this context, it is important to mention that the challenge is that all noise contributions from different sources lead to a harmonious, well-balanced overall sound. The optimization of single sources alone does not automatically result in an ideal overall vehicle sound. The paper highlights modern and innovative NVH measurement technologies as well as presents solutions of recent NVH tasks and challenges. Furthermore, future prospects and developments in the field of automotive acoustics are considered and discussed.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.484-484
• /
• 2022

서식지적합도지수(Habitat Suitability Index, HSI)는 어류의 환경생태유량(Environmental Ecological Flow) 산정과 관련해 국내외에서 PHABSIM (Physical Habitat Simulation System)이나 River2D 모형과 같은 생태수리 모형에 적용되고 있으며, 특히 물리적서식지모의시스템은 흐름특성(유량유속, 수심 등)의 변화에 대한 하도구간 내 대표어종의 물리적 서식지 변화를 예측하여 대상 어종에 대한 가용서식지면적(어류가 살 수 있는 서식지 면적, Weighed Usable Area, WUA)유량 관계를 통해 서식에 필요한 최적 유량을 산정하는 데 목적이 있다. 물리적 서식지적합도지수 산정과 화학적 서식지적합도지수 산정방법은 WDFW (Washington Department of Fish and Wildlife, 2004)방법과 IFASG (Instream Flow and Aquatic Systems Group, 1986)의 방법으로 산정하였다. 섬진강에서 2020년에는 3개지점, 2021년에는 2020년 3개지점과 새로운 3개지점에 대하여 각각 4, 5, 6, 9, 10 및 11월에 어류 조사 및 물리적 조건 등에 대하여 현장 모니터링을 실시하였다. 2차년도 동안 모니터링 결과 섬진강에서는 줄납자루, 섬진자가사리, 참중고기, 참몰개, 잉어, 붕어, 칼납자루, 큰납지리, 누치, 모래무지, 피라미, 치리, 블루길, 배스 14종에 대하여 물리적 및 화학적 HSI를 산정하였다. 주요종의 WDFW 방법에 따른 큰줄납자루는 수심 0.3~0.6 m, 유속 0.1~0.4 m/s, 섬진자가사리는 수심 0.2~0.5 m, 유속 0.3~0.7 m/s, 참중고기는 수심 0.4~0.8 m, 유속 0.1~0.6 m/s, 피라미는 수심 0.3~0.7 m, 유속 0.1~0.5 m/s로 산정되었다. IFASG 방법으로 큰줄납자루는 섬진강에서는 수심 0.64 m에서 최대의 출현도를 보였으며, HSI는 0.46~0.83 m, 유속은 0.59 m/s에서 최대의 출현도를 보였고, HSI는 0.38~0.83 m/s, 하상기질의 선호도는 평균입경(𝚽m) -1.14(grevel)에서 최대의 출현도를 보였으며, HSI -3.35~0.65(grevel~sand)로 산정되었다. 화학적 HSI 산정결과 큰줄납자루는 BOD는 1.0 mg/L에서 최대 출현도를 보였고, HSI는 0.7~1.2 mg/L, T-N은 0.925 mg/L에서 최대 출현도를 보이며 HSI는 0.604~1.277 mg/L, T-P는 0.028 mg/L에서 최대 출현도를 보이며 HSI는 0.021~0.034 mg/L, SS는 3.6 mg/L에서 최대 출현도를 보이며, HSI는 2.1~5.2 mg/L의 범위로 산정되었다. 산정된 범위는 환경부 생활환경기준 BOD 매우좋음(Ia)~좋음(Ib), T-P 매우좋음(Ia)~좋음(Ib) 등급으로 각각 확인되었다. 본 과제는 3차년(2022년)이 아직 남아 있어 HSI에 대하여 약간 보정이 있을 것이며, 최종 HSI가 산정이 되면 향후 환경적 기능을 고려한 중장기 정부 정책의 활용성 높은 기초자료가 될 것이다.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.43 no.6
• /
• pp.16-24
• /
• 2015

This study quantified storage and annual uptake of carbon for riparian greenspaces established in watersheds of four major rivers in South Korea and explored desirable strategies to improve carbon reduction effects of riparian greenspaces. Greenspace structure and planting technique in the 40 study sites sampled were represented by single-layered planting of small trees in low density, with stem diameter at breast height of $6.9{\pm}0.2cm$ and planting density of $10.4{\pm}0.8trees/100m^2$ on average. Storage and annual uptake of carbon per unit area by planted trees averaged $8.2{\pm}0.5t/ha$ and $1.7{\pm}0.1t/ha/yr$, respectively, increasing as planting density got higher. Mean organic matter and carbon storage in soils were $1.4{\pm}0.1%$ and $26.4{\pm}1.5t/ha$, respectively. Planted trees and soils per ha stored the amount of carbon emitted from gasoline consumption of about 61 kL, and the trees per ha annually offset carbon emissions from gasoline use of about 3 kL. These carbon reduction effects are associated with tree growth over five years to fewer than 10 years after planting, and predicted to become much greater as the planted trees grow. This study simulated changes in annual carbon uptake by tree growth over future 30 years for typical planting models selected as different from the planting technique in the study sites. The simulation revealed that cumulative annual carbon uptake for a multilayered and grouped ecological planting model with both larger tree size and higher planting density was approximately 1.9 times greater 10 years after planting and 1.5 times greater 30 years after than that in the study sites. Strategies to improve carbon reduction effects of riparian greenspaces suggest multilayered and grouped planting mixed with relatively large trees, middle/high density planting of native species mixed with fast-growing trees, and securing the soil environment favorable for normal growth of planting tree species. The research findings are expected to be useful as practical guidelines to improve the role of a carbon uptake source, in addition to water quality conservation and wildlife inhabitation, in implementing riparian greenspace projects under the beginning stage.