• Advances in concrete construction
• /
• v.9 no.2
• /
• pp.139-147
• /
• 2020

This paper reports the effect of Rice Husk Ash (RHA) in geopolymer concrete on strength, durability and microstructural properties under ambient curing at a room temperature of 25℃ and 65±5% relative humidity. Rice husk was incinerated at 800℃ in a hot air oven. and ground in a ball mill to achieve the required fineness. RHA was partially added in 10, 15, 20, 25, 30 and 35 percentages to fly ash with 10% of GGBS to produce geopolymer concrete. Test results exhibit that the substitution of RHA in geopolymer concrete resulted in reduced strength properties during initial curing. In the initial stage, workability of GPC mixes was affected by RHA particles due to the presence of dormant particles in it. It is evident from the microstructural study that the presence of RHA particles densifies the matrix reducing porosity in concrete. This is due to the presence of RHA in geopolymer concrete, which affects the ratio of silica and alumina, resulting in polycondensation reactions products. This study suggests that incorporation of rice husk ash in geopolymer concrete is the solution for effective utilization of waste materials and prevention of environmental pollution due to the dumping of industrial waste and to produce eco-friendly concrete.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2007.11a
• /
• pp.93-102
• /
• 2007

Biocomposite was organized with biodegradable polymer and natural fiber that has potential to be used as replacement for glass fiber reinforced polymer composite with the benefits of low cost, low density, acceptable specific strength, biodegradability, etc. Until now, non-wood fibers have been used as reinforcements of biocomposite which are all plant-based fibers. The present study focused on investigating the fabrication and characterization of biocomposite reinforced with red algae fiber. The bleached red algae fiber(BRAF) showed very similar crystallinity to the cellulose. It has high stability against thermal degradation (maximum thermal decomposition temperature of 359.3$^{\circ}C$) and thermal expansion. Biocomposites reinforced with BRAF have been fabricated by a compression molding method and their mechanical and thermal properties have been studied. The storage modulus and the thermomechanical stability of PBS matrix are markedly improved with reinforcing the BRAF. These results support that the red algae fiber can be used as an excellent reinforcement of biocomposites as "green-composite" or "eco-composite".

• Fashion & Textile Research Journal
• /
• v.18 no.6
• /
• pp.889-896
• /
• 2016

This study aims to evaluate the hydrolytic activity of a commercial nitrilase and optimize nitrilase treatment conditions to apply eco-friendly finishing on acrylic fabrics. To assess the possibility of hydrolyzing nitrile bonds in acrylic fabric using a commercial nitrilase, the amounts of hydrolysis products, ammonia and carboxylate ions, were measured. The treatment conditions were optimized via the amount of ammonia. The formation of carboxylate ions on the fabric surface was detected by X-ray photoelectron spectroscopy and wettability measurements. After nitrilase treatment, ammonia was detected in the treatment liquid; thus, nitrilase hydrolyzed the nitrile bonds in acrylic woven fabric. The largest amount of ammonia was released into the treatment liquid under the following conditions: pH 8.0, $40^{\circ}C$, and a treatment time of 5 h. The formation of carboxylate ions on the acrylic woven fabric surface by nitrilase hydrolysis was proven by the increased O1s content measuring of XPS analysis. From comparison of the results of nitrilase and alkaline hydrolysis, the white index and strength of the alkali-hydrolyzed acrylic fabric decreased, whereas those of the nitrilase-hydrolyzed samples were maintained. The nitrilase hydrolysis improved the sensitivity of acrylic fabrics to basic dye similarly to alkaline hydrolysis without the drawbacks of yellowing and decreased strength caused by alkaline hydrolysis.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.4
• /
• pp.9-16
• /
• 2018

Recently, the demand for eco-friendly parts has increased to reduce materials and parts that use fossil fuels. This has exacerbated the increase of energy prices and the enforcement of regulations by environmental agencies. Currently, polylactic acid (PLA) is a solution, as a common and eco-friendly material. PLA is a biodegradable material that can replace traditional petrochemical polymers. PLA has great advantages since it is resistant to cracking and shrinkage. When it is manufactured, there are few harmful byproducts. Improvement in the brittleness characteristics is another important task to be monitored throughout the production of industrial parts. Improvement in the brittleness property of products lowers the tensile strength and tensile elasticity modulus of the parts. This study focused on the mechanical properties of 3D-printed PLA parts. Tensile tests are performed while varying the infill print parameters to evaluate the applicability of PLA in several industrial areas.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.46 no.1
• /
• pp.53-56
• /
• 2001

Barley Yellow Dwarf Virus (BYDV), an aphid-borne luteovirus, is a major plant pathogenic disease causing a huge economic loss in the grain production of a wide range of Gramineae species throughout the world. It has been recently reported that BYDV also occurred frequently in wheat field of Korea. Here, we performed to develop the detection and classification methods of BYDV strains that were accomplished by reverse transcription-polymerase chain reaction (RT-PCR). Since there are high variations among BYDV strains, three pairs of primers were designed to detect BYDV strains such as PAV (Vic-PAV and CN-PAV) and MAV (primer A) simultaneously, specifically Vic-PAV(primer B), and MAV (primer C) based on the genomic RNA sequences of BYDV strains previously published. The validity of the primers was confirmed using several BYDV strains obtained from CIMMYT. Though three BYDV strains were able to be detected using primer A, PCR products were not distinguished between two PAV strains. It was possible to separate them with a restriction enzyme, EcoRI, whose restriction site was present in the amplified DNA fragment from Vic-PAV, but not from CN-PAV.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.4
• /
• pp.416-429
• /
• 2010

The market-based fisheries resources management system was reviewed and the improvement scheme was studied for seeking the sustainability of marine ecosystems and their fisheries resources. A demand-side policy is currently emerging to the management of fisheries resources by reducing over-exploitation, based on the consumer's selection. The role of consumers in the sustainable fishery was studied by comparing the social responsibility and consumer's activity between Korea and foreign countries and international NGO groups, based on the FAO guideline. The adoption of the Marine Stewardship Council (MSC)'s eco-labelling certificate was suggested by expanding the existing environment-friendly certification system in Korea. This new system will contribute to the protection of young immature fish and spawners in coastal and offshore fisheries as well as to the international trade of seafood in terms of fish products from well-managed fisheries. It is noted that the consumer's activities in the markets as regulators will contribute to the ecosystem health and sustainability.

• Elastomers and Composites
• /
• v.46 no.1
• /
• pp.2-9
• /
• 2011

Permeability to gases and vapors is an important function in tires, rubber tubes and diaphragms. It mainly depends on the rubber material. Generally, permeability increases in the following order: silicone rubber > NR > EPDM > SBR > NBR > FPM > ECO > IIR. And, for an elastomer permeability is also very much dependent on compounding. Many research works are reported in the area of gas permeability for formed rubber,$^{1-7}$ however, few studies are found for unformed elastomer products. Incorporation of nano-particles, use of thermoplastic elastomers and applying high barrier multilayer coatings are the main approaches to obtain a high barrier elastomeric product. In this paper, barrier article for vehicle is introduced.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.2
• /
• pp.86-95
• /
• 2023

This paper explained the equipment and process development to secure the source technology of controlled nitrification technology. The nitriding potential in the furnace was controlled only by adjusting the flow rate of ammonia gas introduced into the furnace. In addition, a control system was introduced to automate the nitriding process. The equipment's hardware was designed to enable controlled nitriding based on the conventional gas nitriding furnace, and an automation device was attached. As a result of measuring the temperature and quality uniformity for the equipment, the temperature and compound uniformity were ±1.2℃ and 14.3 ± 0.2 ㎛, respectively. And, it was confirmed that nitriding potential was controlled within the tolerance range of AMS2759-10B standard. In addition to parts for controlled nitriding, it was applied to products produced in existing conventional nitriding furnaces, and as a result, gas consumption was reduced by up to 80%.

• Journal of Mushroom
• /
• v.21 no.3
• /
• pp.83-87
• /
• 2023

The importance of biocomposites has increased owing to the changes in global consumption trends and rapid climate change. Technologies using mushroom mycelium cultivation, and molding methods for mycelial application have gained attention as potential strategies for producing eco-friendly composites. Currently, mushroom mycelia are used as raw materials for food and cosmetics; however, research on their utilization as biocomposite materials is limited. Therefore, the potential for the development of mushroom mycelium-related products and technologies is high. This review analyzes the domestic and international patent application trends related to the technologies for composite (packaging, insulation, adhesives, and leather) and food (substitute for meat) materials using mushroom mycelium, as an eco-friendly biocomposite material, to provide objective patent information that can further research and development (R&D) in this field.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.1630-1636
• /
• 2009

Nine alkali-activated (AA) mortars were mixed and cured at water or air-dried conditions to explore the significance and limitation for the application of the combination of Ba and Ca ions as an alkali-activator. Ground granulated blast-furnace slag (GGBS) was used for source materials, and calcium hydroxide (Ca(OH)₂) and barium hydroxide (Ba(OH)₂) were employed as alkali activators. Test results clearly showed that the water curing condition was more effective than the air-dried curing condition for the formation of the denser calcium silicate hydrate (C-S-H) gels that had a higher molar Si/Ca ratio, resulting in a higher strength development. At the same time, the introduction of Ba(OH)₂ led to the formation of 2CaO·Al₂O₃·SiO₂·8H₂O (C₂ASH₈) hydrates with higher molar Si/Al and Ca/Al ratios. Based on the test results, it can be concluded that the developed cementless mortars have highly effective performance and high potential as an eco-friendly sustainable building material.