• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3134-3138
• /
• 2007

The objective of this paper is to elucidate the characteristic performance of the mini-vacuum pump with various heights of eccentric shaft. The mini-diaphragm pump is composed of DC motor, eccentric shaft and diaphragm and it is operated by PCB panel. The height of eccentric shaft is changed that controls the quantities of air flow to improve the performance of vacuum pressure. This device is manufactured in order to embody the vacuum pressure with 200 mmHg. The heights of eccentric shaft which is used in present experiment are located in the range from 3 mm to 5.5 mm. The vacuum pressure distributions with each height of eccentric shaft was measured and the results were graphically depicted.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.587-591
• /
• 2011

To improve the performance of the control butterfly valve seals are used to eccentric shaft. In this case, vertical opening gas of the butterfly valve is non-symmetrical, which will change the flow pattern around the valve. In this study, the eccentric drive shaft of the butterfly valve to change flow characteristics are performed numerically. Flow pattern and pressure drop are investigated as the valve opening angle increases for a given mass flow rate. The valve flow coefficient is compared to the without eccentric shaft.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.815-816
• /
• 2013

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2017년도 추계학술발표회
• /
• pp.264-264
• /
• 2017

• 소성∙가공
• /
• 제14권1호
• /
• pp.57-64
• /
• 2005

This study deals with the cold forging process design for shaft in the main part of automobile motors with rectangular deep groove. In forging process, the accuracy and die lift is very important because it have influence on reduction of the production cost and the increase of the production rate. Therefore, it is necessary to develop the manufacturing process of shaft by cold forging., process variables are the cropped face angle of billet and the eccentric load of punch. The former is derived from cropping test, the latter is occurred by clearance between container and preform. Also, grooved preform select the process variable for decrease in punch deflection. We investigate that a deflection of punch and a deformation of preform to every process variables. Through this investigation, we suggest the optimal preform and process design, expect to be improved the tool life in forging process.

• 한국소음진동공학회논문집
• /
• 제23권3호
• /
• pp.234-239
• /
• 2013

There are many types of speed reducer for industrial uses. However the cycloid speed reducer is widely used in manipulators based on excellent performance of low backlash, high reduction ratio and compact size. It is essential to use precision speed reducer for accuracy of position controls on robot systems and electric vehicles. The cycloid speed reducer has a eccentric rotating motion and offset to avoid some problem of assembly, so it has a disadvantage for vibration. In this paper, a multi-body dynamic model is developed for a cycloid speed reducer and the dynamic behaviors of the reducer are investigated. The cycloid speed reducer consists of cycloidal plate gears, housing gear, input shaft, output pin and shaft, and eccentric bearings. Using a CAD program, each component of cycloid reducer is modeled based on the offset and eccentric. Multi-body simulations using Recurdyn and test using a rig tester are performed. As a result, the pin reaction force and the amplitude of housing displacement are increased by the larger offset and smaller eccentric value of cycloid reducer.

• 해양환경안전학회지
• /
• 제24권4호
• /
• pp.482-488
• /
• 2018

선박 축계는 프로펠러 하중의 영향으로 선미관 후부베어링의 국부하중 증가가 현저히 나타나 축계 선미관 베어링 손상의 위험이 증대된다. 이를 방지하기 위해 수행된 추진축계 정렬연구는 주로 준정적 상태(quasi-static condition)에서 축과 지지베어링간의 상대적 경사각을 감소시키는데 중점을 두어 진행되어 왔다. 그러나 보다 상세한 평가를 위해서는 동적상태를 추가로 고려하는 것이 필요하다. 4,700 DWT 선박을 대상으로 NCR로 운전중 급속으로 우현 전타할 때 추진축계가 받는 영향에 대해 연구하였다. 연구결과 선미 유동장 변화에 의해 프로펠러 편심추력이 과도 상태가 되어 프로펠러에 불평형 진동이 유발되는 것을 확인하였다. 우현 전타시의 프로펠러 편심추력은 NCR 조건대비 축을 선미관 베어링으로부터 들어 올리는 힘으로 작용하여 선미관 베어링 하중완화에 기여하고 있음을 확인하였다.

• Tribology and Lubricants
• /
• 제17권6호
• /
• pp.426-434
• /
• 2001

The hermetic reciprocating compressor driven by the BLDC motor rotating with variable speeds, is modelled and analyzed for dynamic characteristics. The governing equations of piston, connecting rod and crank-shaft of the reciprocating compression mechanism and characteristics of driving torque of the motor are obtained. Dynamic behavior of the crankshaft supported on 2 journal bearings is analyzed considering compression load and eccentric unbalance for the 4 rotating speeds of crankshaft. And. reaction forces generated from oil film in the journal bearings are analyzed under transient condition using Reynolds' equation. To take into account the dynamic characteristics depending on the variable rotating speeds, comparison on the dynamic behavior of crank-shaft is made for the 4 operating modes of the compressor. Results show that the magnitude of crankshaft locioperating on the lower rotating speeds is more larger than the higher ones due to reduction of inertia force of the reciprocating piston.

• 해양환경안전학회지
• /
• 제26권4호
• /
• pp.412-418
• /
• 2020

선박 축계를 구성하는 프로펠러축은 엔진출력, 프로펠러 하중 및 편심추력의 영향으로 인해 거동의 양상이 달라져 선미관 후부베어링의 국부하중 변화를 일으킴으로써 선미관 베어링 손상의 위험을 증가시킨다. 이를 방지하기 위해 수행된 추진축계 정렬연구는 선급강선규칙을 중심으로 주로 축과 지지베어링간의 상대적 경사각과 유막유지를 최적화 하는데 중점을 두어 진행 되어왔다. 그러나 보다 상세한 평가를 통한 추진축계의 안정성 확보를 위해서는 전타와 같은 급격한 선미유동장 변화에 기인한 과도상태를 포함한 동적상태의 고려가 필요하다. 이러한 관점에서, 본 연구는 50,000 DWT 선박을 대상으로 스트레인 게이지법을 이용하여 밸러스트 흘수 상태에서 정격회전수로 운전 중 대표적 동적 과도상태인 우현 전타상태에서의 프로펠러 축 거동이 추진축계에 미치는 영향을 분석하였다. 그 결과 변동된 프로펠러 편심추력은 프로펠러축을 일시적으로 강하게 내려 누르는 힘으로 작용하여 선미관 베어링의 국부하중을 증가시켜 축계 안정성에 부정적 영향을 미침을 증명하였다.

• 한국자동차공학회논문집
• /
• 제1권1호
• /
• pp.80-89
• /
• 1993

Performance simulation for a Spark Ignition Wankel rotary Engine is presented in this paper. The volume of chamber at each eccentric shaft angle is evaluated by using geometric models of housing and rotor. A thermodynamic model which includes the first law of thermodynamics, combustion and convective heat transfer from chamber contents to surroundings is imployed. A thermochemical equilibrium model which considers 10 species(CO, $CO_2$, $O_2$, $H_2$, $H_2O$, OH, O, NO, $N_2$) in the burned gas region, is also employed. Four processes of gas exchange, compression, combustion and expansion are considered and the pressure, temperature and composition of chamber gas at each eccentric shaft angle in each process are computed in this performance simulation. This performance simulation must be useful for optimal design of Spark Ignition Wankel Rotray Engine with parametric study for various design parameters and operating conditions.