• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.5
• /
• pp.385-393
• /
• 2021

This study proposes a multi-core-based controller design for an ESC(Electronic Stability Control) system in an automotive multi-core processor. Considering the architectures of an automotive multi-core processor and an ESC system, the overall execution time has been optimized for multi-core platforms. The function module assignment, synchronization between cores, and memory assignment for core-dependent variables in automotive multi-core systems are evaluated. The ESC controller comprising five function modules is used herein. Based on the proposed design, the single-core controller is extended to multi-core controllers. Using multi-core optimization methods, such as function module assignment, semaphore, interrupt awakening, and variable assignment over cores, the ESC system is redesigned to a multi-core controller. Experimental results reveal that the execution time for the multi-core processor is reduced by 59.7% compared with that for the single-core processor.

• Journal of Korean Society of Transportation
• /
• v.35 no.4
• /
• pp.307-320
• /
• 2017

The objective of this study is to identify the effectiveness of ESC(Electronic Stability Control) based on a meta analysis technique. Accident Rate, Fatal Crash Rate, Loss of Control Crash Rate were set as indexes of traffic safety evaluation. Also, reviews on the effectiveness of ESC were collected using keyword, 'ESC'. As a result, the Effect size of accident rate odd ratio was 0.90. When ESC system was applied on vehicles, accident rate decreased by 10%. Also, the Effect size of fatal crash rate odd ratio was 0.64. When ESC system was applied on vehicles, fatal crash rate decreased by 36%. Lastly, the Effect size of loss of control crash rate odd ratio was 0.73. When ESC system was applied on vehicles, loss of control crash rate decreased by 27%. The outcome of this study would be effectively used for developing polices and regulations for ESC installation obligation of commercial vehicles.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.12
• /
• pp.2306-2313
• /
• 2010

This paper describes a model based fault detection algorithm for an Advanced ESC System which consists of Hydraulic Control Unit (HCU) with built-in wheel pressure sensors. Advanced ESC System can be used for various value-added functions such as Stop & Go Function and Regenerative Brake Function. Therefore, HCU must have a reliable fault detection. Due to the huge amount of sensor signals, existing specific sensor based fault detection of HCU cannot guarantee the safety of vehicle. However, proposed algorithm dose not require the sensors. When model based fault detection algorithm detects severe failures of the HCU, it warns the driver in advance to prevent accidents due to the failures. For this purpose, a mathematical model is developed and validated in comparison to actual data. Simulation results and data acquired from an actual system are compared with each other to obtain the information needed for the fault detection process.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.87-96
• /
• 2013

This paper shows how the performance of an ESC(Electronic Stability Control) system can be affected by the selection of in-vehicle network protocols such as CAN or FlexRay. The vehicle control performance under ESC operation is analyzed by EILS(ECU-In-the-Loop Simulation). The experimental set-up for the EILS of the ESC system consists of two 32-bit microcontroller boards communicated with CAN or FlexRay protocols. A 7-DOF vehicle model and an ESC algorithm with 2-DOF reference vehicle model are implemented on each microcontroller respectively. It is shown by experimental results that the ESC system using the FlexRay protocol can achieve better performance than that using the CAN protocol for a fast and accurate lane changing.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.5
• /
• pp.106-111
• /
• 2007

After the semiconductor processing, wafer is attracted by ESC(Electrostatic Chuck) with remaining electric charge. That causes too many problems for examples, sliding of wafer, popping or broken. This paper presents the model of ESC for silicon wafer, which is modeled by electrical circuit component such as capacitor. The simulations using PSpice result in the phenomenon of silicon wafer was charged by ESC. In this paper we suggest the discharging method. for wafer.

• Journal of Auto-vehicle Safety Association
• /
• v.7 no.2
• /
• pp.32-38
• /
• 2015

A sine with dwell test is well known as a test scenario for evaluation of performance of electronic stability control(ESC) on passenger vehicles and heavy commercial vehicles. However, when it comes to ESC for medium commercial vehicles, the test scenario has not been established yet. In this paper, the sine with dwell test was modified considering characteristics of medium commercial vehicles. The three main modifications of the original test scenario are the steering angle level, steering frequency, and loading condition of the vehicle. These modifications are derived from simulation study for different medium commercial vehicles. From simulation study, it was shown that the ESC system for medium commercial vehicle is objectively evaluated by the proposed test scenario. A clear improvement on vehicle stability was seen in the results when ESC system was used.

• Journal of the Semiconductor & Display Technology
• /
• v.1 no.1
• /
• pp.9-13
• /
• 2002

A polyimide-type electrostatic chuck (ESC) was fabricated for the application of holding 8-inch silicon wafers in the oxide etching equipment. For the fabrication of the unipolar ESC, core technologies such as coating of polyimide films and anodizing treatment of aluminum surface were developed. The polyimide films were prepared on top of thin coated copper substrates for the good electrical contacts, and the helium gas cooling technique was used for the temperature uniformity of the silicon wafers. The ESC was essentially working with an unipolar operation, which was easier to fabricate and operate compared to a bipolar operation. The chucking force of the ESC has been measured to be about 580 gf when the applied voltage was 1.5 kV, which was considered to be enough force to hold wafers during the dry etching processing. The employment of the ESC in etcher system could make 8% enhancement of the wafer processing yield.

• Journal of Advanced Navigation Technology
• /
• v.27 no.2
• /
• pp.214-220
• /
• 2023

Because there exist a region in the rotational speed and torque map that the a particular combination of a motor and an ESC (Electronic Speed Control) can maintain its peak efficiency, identifying this region is important for designing an efficient system. Firstly the accuracy of the measurement device is verified using the published propeller measurement data. And then, the combined motor-ESC efficiencies of an individual propeller are measured at a wide range of rotational speeds. With measurements obtained from a large number of different propellers, efficiency contours are obtained. It is shown that there exist a significant difference between the measured combined efficiency and the motor efficiency computed using a simple model. In addition, with the same motor, the combined efficiency can have a meaningful variation depending on the model of the ESC. The efficiency contours derived from this study will be useful for the design and optimization of electric propulsion systems of an aircraft where propulsion efficiency is critical.

• Advances in Automotive Engineering
• /
• v.1 no.1
• /
• pp.123-141
• /
• 2018

Hardware-in-the-loop (HiL) simulation is a very powerful tool to design, test and verify automotive control systems. However, well-validated and high degree of freedom vehicle models have to be utilized in these simulations in order to obtain realistic results. In this paper, a vehicle dynamics model developed in the Carsim Real Time program environment and its validation has been performed using experimental results. The developed Carsim real time model has been employed in the Tofas R&D hardware-in-the-loop simulator. Experimental and hardware-in-the-loop simulation results have been compared for the standard FMVSS No. 126 test and the results have been found to be in good agreement with each other. Two electronic stability control (ESC) algorithms, named the Basic ESC and the Integrated ESC, taken from the earlier work of the authors have been tested and evaluated in the hardware-in-the-loop simulator. Different evaluation methods have been formulated and used to compare these ESC algorithms. As a result, the Integrated ESC system has been shown superior performance as compared to the Basic ESC algorithm.

• Reproductive and Developmental Biology
• /
• v.34 no.3
• /
• pp.143-151
• /
• 2010

Pluripotency of human embryonic stem cell (hESC) is one of the most valuable ability of hESCs for applying cell therapy field, but also showing side effect, for example teratoma formation. When transplant multipotent stem cell, such as mesnchymal stem cell (MSC) which retains similar differentiation ability, they do not form teratoma in vivo, but there exist limitation of cellular source supply. Accordingly, differentiation of hESC into MSC will be promising cellular source with strong points of both hESC and MSC line. In this study, we described the derivation of MSC like cell population from feeder free cultured hESC (hESC-MSC) using direct differentiation system. Cells population, hESC-MSC and bone marrow derived MSC (BM-MSC) retained similar characteristics in vitro, such as morphology, MSC specific marker expression and differentiation capacity. At the point of differentiation of both cell populations, differentiation rate was slower in hESC-MSC than BM-MSC. As these reason, to verify differentially expressed molecular condition of both cell population which bring out different differentiation rate, we compare the molecular condition of hESC-MSC and BM-MSC using 2-D proteomic analysis tool. In the proteomic analysis, we identified 49 differentially expressed proteins in hESC-MSC and BM-MSC, and they involved in different biological process such as positive regulation of molecular function, biological process, cellular metabolic process, nitrogen compound metabolic process, macromolecule metabolic process, metabolic process, molecular function, and positive regulation of molecular function and regulation of ubiquitin protein ligase activity during mitotic cell cycle, cellular response to stress, and RNA localization. As the related function of differentially expressed proteins, we sought to these proteins were key regulators which contribute to their differentiation rate, developmental process and cell proliferation. Our results suggest that the expressions of these proteins between the hESC-MSC and BM-MSC, could give to us further evidence for hESC differentiation into the mesenchymal stem cell is associated with a differentiation factor. As the initial step to understand fundamental difference of hESC-MSC and BM-MSC, we sought to investigate different protein expression profile. And the grafting of hESC differentiation into MSC and their comparative proteomic analysis will be positively contribute to cell therapy without cellular source limitation, also with exact background of their molecular condition.