• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.4
• /
• pp.89-97
• /
• 2014

As the digital control technologies in automotive industry have advanced, electronic control units(ECUs) play a key-role to improve system performance. Transmission control unit(TCU) is a shifting controller for automatic transmission of which major functions are to determine the shift and manage the shifting process considering the various sensor signal on transmission and driver's commands. As with any ECU in vehicle, TCU performs complex algorithms such as shift control, diagnostic and failsafe functions. However, firmware design analysis is hardly possible by the reverse engineering due to code protection. Transmission simulator is a hardware-in-the-loop simulator which enables TCU to work in normal mode by simulating the electrical signal of TCU interface. In this research, diagnosis and failsafe algorithm implemented on commercialized TCU is analyzed by using the transmission simulator that is developed for wheel loader construction vehicle. This paper gives various experimental results on the proportional solenoid current trajectories for different operating modes, error detection criterion and limphome mode gears for all the possible cases of clutch malfunction. The derived results for conventional TCU can be applied to the development of inherent TCU algorithms and the transmission simulator can also be utilized for the test of TCU to be developed.

• Journal of Drive and Control
• /
• v.11 no.4
• /
• pp.61-67
• /
• 2014

When a manual transmission equipped car stops on an incline where the nose of the car is higher than the rear, hill-start control or hill-holder could prevent the vehicle from rolling backward as the car moves forward. The easy-hill assist valve consists of a check valve and a needle type ON/OFF solenoid valve connected in parallel; it is a hydraulic actuator that can maintain brake pressure using an electrical signal from the ECU. As the EHA valve is a safety-related component of the brake system, high reliability as well as superior dynamic performance is required for it to be applied in commercial vehicles. This paper presents the design of the EHA valve as a piece of equipment that can simulate the brake actuation pressure with a pressurizing piston. Following specific test standards, the experimental results validate the implemented functions of the test equipment, proving the test stand to be effective for the performance and endurance of the EHA valve.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.10
• /
• pp.1448-1453
• /
• 2015

In this paper, we propose an alternative method of communication to improve the reliability of in-vehicle networks by jointly using wireless communication networks. Wired Communication networks have been used in vehicles for the monitoring and the control of vehicle motion, however, the disconnection of wires or hardware fault of networks may cause a critical problem in vehicles. If the network manager detects a disconnection or faults in wired in-vehicle network like the Controller Area Network(CAN), it can redirect the communication path from the wired to the wireless communication like the Zigbee network. To show the validity and the effectiveness of the proposed in-vehicle network architecture, we implement the Electronic Stability Control(ESC) system as ECU-In-the-Loop Simulation(EILS) and verify that the control performance can be kept well even if some hardware faults like disconnection of wires occur.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2022.05a
• /
• pp.531-534
• /
• 2022

승차 공유, 카풀, 렌터카의 이용률이 증가하면서 많은 사용자가 동일한 차량에 로컬 액세스 할 수 있는 시나리오가 더욱 보편화됨에 따라 차량 네트워크에 대한 공격 가능성이 커지고 있다. 차량용 CAN Bus Network에 대한 DoS(Denial of Service), Fuzzy Attack 및 Replay Attack과 같은 공격은 일부 ECU(Electronic Controller Unit) 비활성 및 작동 불능 상태를 유발한다. 에어백, 제동 시스템과 같은 필수 시스템이 작동 불가 상태가 되어 운전자에게 치명적인 결과를 초래할 수 있다. 차량 네트워크 침입 탐지를 위하여 많은 연구가 진행되고 있으나, 기존 화이트리스트를 이용한 탐지 방법은 새로운 유형의 공격이 발생하거나 희소성이 높은 공격일 때 탐지하기 어렵다. 본 논문에서는 인공신경망 기반의 CAN 버스 네트워크 침입 탐지 기법을 제안한다. 제안하는 침입 탐지 기법은 2단계로 나누어 진다. 1단계에서 정상 패킷 분포를 학습한 VAE 모형이 이상 탐지를 수행한다. 이상 패킷으로 판정될 경우, 2단계에서 인코더로부터 추출된 잠재변수와 VAE의 재구성 오차를 이용하여 공격 유형을 분류한다. 분류 결과의 신뢰점수(Confidence score)가 임계치보다 낮을 경우 학습하지 않은 공격으로 판단한다. 본 연구 결과물은 정보보호 연구·개발 데이터 첼린지 2019 대회의 차량 이상징후 탐지 트랙에서 제공하는 정상 및 3종의 차량 공격시도 패킷 데이터를 대상으로 성능을 평가하였다. 실험을 통해 자동차 제조사의 규칙이나 정책을 사전에 정의하지 않더라도 낮은 오탐율로 비정상 패킷을 탐지해 낼 수 있음을 확인할 수 있다.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.33 no.2
• /
• pp.325-336
• /
• 2023

With the development of autonomous driving technology, the number of external contact sensors mounted on vehicles is increasing, and the importance is also rising. The vehicular ultrasonic sensor uses the LIN protocol in the form of a bus topology and reports a status message about its surroundings through the vehicle's internal network. Since ultrasonic sensors are vulnerable to various threats due to poor security protocols, physical testing on actual vehicle is needed. Therefore, this paper developed a LIN-CAN co-analysis testbed with a jig for location-specific distance test to examine the operational relation between LIN and CAN caused by ultrasonic sensors.

• Tribology and Lubricants
• /
• v.30 no.3
• /
• pp.183-188
• /
• 2014

In this paper, we present our analysis of tribological failure examples for an anti-lock brake system(ABS) in a car. The study range of this paper is to improve the quality of ABS system by analyzing with sensor, computer, actuator and oil lines. In the first example, the brake leak from hydraulic supply line in a caliper on the rear left side of the ABS hydraulic modulator. This produces the sponge phenomenon, where the car does not brake even when the driver operates the brake pedal. The hydraulic unit operating ABS is actuator that play role regulating drive condition according with the oil pressure supplied with wheel of a car. In the second example, the service man does not completely tighten the fixed bolt after repairing the car. This causes the ABS warning lamp to light up as the ABS wheel speed sensor cannot detect whether the ABS has been activated. In the third example, the ABS electronic control unit is separated from the soldered part of the inner circuit board. Consequently, the ABS fails in control because the ABS motor pump receives no-signal for the hydraulic unit. The wheel speed sensor has to large durability because of giving signal of acting condition to computer by detected the acceleration and deceleration of wheel of a car. In the fourth example, the ABS warning lamp lights up of when cracks propagate in the circuit board soldering part. The circuit of this computer is very important part for input and output the operating signal of system. Such failures can aggravate the durability of the ABS. Thus, the ABS needs to be optimized to eliminate malfunction phenomenon.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.354-358
• /
• 2009

Micro gas turbine engine is well known as a power plant of unmanned aerial vehicle and a small scale emergency generation system and also, it is significant as initial research of large gas turbine and educational purpose of gas turbine. Many sort of Micro gas turbine test set for education is produced by several manufacturers, but all of the engine control system of them is separated with data acquisition system; moreover, the engine control algorithms are inaccessible and related variables could not be collected. In this investigation, the Integrated Modifiable Test Rig which has modifiable engine start-up, drive and situational control logics is developed by LabVIEW with I/O devices and it provides wide experimental applicability to studies of dynamic characteristics of fuel system and combustion instability.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.4
• /
• pp.17-22
• /
• 2009

FlexRay is a new standard of network communication system which provides solutions to the degradation problems generated by many ECU (Electronic Control Unit) connections in automobiles and automation systems. The upper bound of the data rate is 10Mbps and it provides two channels for redundancy In this paper, FlexRay system is first designed using SDL. For hardware implementation, FlexRay system is designed using Verilog HDL based on the SDL design result. The designed system is synthesized using Synopsys Design Compiler with the Magna/Hynix 0.18 um cell library. In this paper, to construct a FlexRay network, active star is used since active star systems can provide high speed data transmission up to 10Mbps. The performance of the star network is tested using one transmitter node and two receiver nodes.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.105-108
• /
• 2010

The vehicle navigation system is a representative driver supporting system that available to present searching and guiding path functions, have been increased for usability. Under competition situation because of following the spreaded navigation market, to meet customer's needs about new given services, there are need differentiated services increasing dramatically. Also now, dash board indicates various vehicle's status and driver can aware of that. However it is not easy to know where is abnormal essentially and there are no devices to give warning to driver. Therefore, It is difficult to preserve accidents because it can't deal with various abnormal functions immediately on driving. In this paper, we proposed vehicle diagnosis program within navigation that is available to manage and to make a diagnosis of vehicle. And this program conform OBD-II standard, so it can transmit diagnosis data from ECU to navigation system using Bluetooth wireless communication protocol. Thus this program give enhanced services to customer as well as multimedia and geometry information services.

• Journal of Institute of Convergence Technology
• /
• v.2 no.1
• /
• pp.24-30
• /
• 2012

In this study, the trucks(2.9-liter) have been developed to use DME as fuel, and performance test of the vehicle's DME engine, power, emissions, fuel economy and vehicle aspects was conducted. For experiments, the fuel system(common-rail injectors and high-pressure pump included) and the engine control logic was developed, and ECU mapping was performed. As a result, the rail pressure from 40MPa to approximately 65% increase compared to the base injector has been confirmed that. Also, the pump discharge flow is 15.5 kg/h when the fuel rail pressure is 400rpm(40 MPa), and the pump discharge flow is 92.1 kg/h when the fuel rail pressure is 2,000rpm(40MPa). The maximum value of full-load torque capability is 25.5kgfm(based on 2,000rpm), and more than 90% compared to the level of the diesel engine were obtained. The DME vehicle was developed in this study, 120 km/h can drive to the stable, and calculated in accordance with the carbon-balance method of fuel consumptions is 5.7 km/L.