• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 C
• /
• pp.1512-1516
• /
• 1994

FLIC(Fluid in cell) method has been used for analyzing a cold gas flow field in an interrupter of a circuit treater since 1970s. In this paper FLIC method is applied to calculation of a cold gas flow and then combined with the simple are analysis method in order to investigate the flow field characteristics in a puffer type interrupter rated at 145kV 40kA. The results for a cold gas flow agree with the experimental measurement well. The other results such as pressure rise, arc temperature, post-arc current and so forth am also reasonable and show the possibility that the combined program can be applied to the design of UHV interrupters.

• 전기의세계
• /
• 제17권2호
• /
• pp.11-15
• /
• 1968

One of the most important methods used in the modern analysis of linear networks and systems is the signal flow graph technique, first introduced by S.J. Mason in 1953. In essence, the signal-flow graph technique is a graphical method of solving a set of simultaneous. It can, therefore, be regarded as an alternative to the substitution method or the conventional matrix method. Since a flow-graph is the pictorial representation of a set of equations, it has an obvious advantage, i.e., it describes the flow of signals from one point of a system to another. Thus it provides cause-and-effect relationship between signals. And it often significantly reduces the work involved, and also yields an easy, systematic manipulation of variables of interest. Mason's formula is very powerful, but it is applicable only when the desired quantity is the transmission gain between the source node and sink node. In this paper, author summarizes the signal-flow graph technique, and stipulates three rules for conversion of an arbitrary nonsource node into a source node. Then heuses the conversion rules to obtain various quantities, i.e., networks gains, functions and parameters, through simple graphical manipulations.

• 설비공학논문집
• /
• 제13권5호
• /
• pp.356-367
• /
• 2001

A numerical analysis on branch type sparger in drain tank for depressurization is performed to investigate the flow characteristics due to the change of design factor. As the result of this study, sparger\\`s flow resistance coefficient(K) is 3.53 at the present design condition when engineering margin for surface roughness is considered as 20%, and flow ratio into branch pipe ($Q_s/Q_i$) is 0.41. The correlation for calculating flow resistance coefficients as design factor is presented. Flow resistance coefficient is increased as section area ratio of branch pipe for main pipe and outlet nozzle diameter of main pipe decreasing, but the effects of branch angle and inlet flow rate of main pipe are small. As the change rate of ($Q_s/Q_i$)becomes larger, the change rate of flow resistance coefficient increases. The rate of pressure loss has the largest change as section area ratio changing. The condition of maximum flow resistance in sparger is when the outlet nozzle diameter ratio of main pipe ($D_e/D_i$) is 0.167, the section area ratio ($A_s/A_i$) is 0.1 and the branch angle ($\alpha$) is 55^{\circ}$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 C
• /
• pp.1287-1289
• /
• 1999

The UPFC(Unified Power Flow Controller) controls the magnitude and phase of the series injected voltage to exchange the real and reactive power with transmission line. The UPFC consists of two inverters connected together through the DC link capacitor. This paper describes the detailed UPFC switching-level model. PWM (Pulse Width Modulation) method is chosen to operate the inverters. Automatic voltage control mode and automatic power flow control mode is selected to control the UPFC. EMTP simulation is offered to obtain the basic operation characteristics of the UPFC and the dynamic characteristics of the UPFC is studied in detail.

• 한국농공학회지
• /
• 제35권2호
• /
• pp.57-64
• /
• 1993

A modified kinematic wave model of the overland flow in vegetated filter strips was developed. The model can predict both flow depth and hydraulic radius of the flow. Existing models can predict only mean flow depth. By using the hydraulic radius, erosion, deposition and flow's transport capacity can be more rationally computed. Spacing hydraulic radius was used to compute flow's hydraulic radius. Numerical solution of the model was accomplished by using both a second-order nonlinear scheme and a linear solution scheme. The nonlinear portion of the model ensures convergence and the linear portion of the model provides rapid computations. This second-order nonlinear scheme minimizes numerical computation errors that may be caused by linearization of a nonlinear model. This model can also be applied to golf courses, parks, no-till fields to route runoff and production and attenuation of many nonpoint source pollutants.

• 한국정보시스템학회지:정보시스템연구
• /
• 제23권2호
• /
• pp.25-47
• /
• 2014

Based on the levels of inter-organizational information flow and the degrees of suppliers' power, this study aims to develop a framework useful for classifying four types of the buyer's e-commerce strategies in manufacturing firms: e-marketplace, e-partnership, e-procurement and supplier's e-marketplace (e-distribution). We adopted a multi-methodological approach by mixing both qualitative and quantitative methods. After developing a framework, through the cases of Cisco, JAL, Toyota Motor, KIST, AMP, and 3M, this paper aims to confirm the actual existence of the four forms of e-commerce. The results from the cases supported the four types of e-commerce strategies in manufacturing firms. With the empirical data, we also demonstrated the configuration of the framework and the four types of e-commerce strategies, and identified the characteristics (i.e., size, age, actual adoption rate of the each type of e-commerce, and supply-chain performance) of the organizations employing each strategy.

• 수산해양기술연구
• /
• 제53권4호
• /
• pp.337-348
• /
• 2017

The tension of warp from trawler and sea-floor contact can generate tilt and wake turbulence around otter boards. Preliminary measurements of otter board tilt and 3-D flow velocity during bottom trawl operations were taken using a vector instrument to investigate the effects of wake turbulence at the trailing edge of the otter board. Tilt data (i.e., yaw, pitch, and roll) at 1 Hz and flow data (velocities in the towing, lateral, and vertical directions) at 16 Hz were analyzed to determine their periods and amplitudes using global wavelet and peak event analyses. The mean period (${\pm}standard$ deviation) of the tilt from the peak event analysis ($5{\pm}2s$) was longer or double than that of flow velocity ($3{\pm}2s$). The two periods also had a significant linear relationship. The turbulence rate of flow was 30-50% at the trailing edge and was closely related to roll deviation. The frequency of phase difference ratios (i.e., peak time differences between tilts and flow periods) was significantly different from random occurrence in two trials, possibly due to side tidal effects. However, in the other trials, flow peaks were random, as shown by the even peak times between tilts and flows. Future studies should focus on reducing tilt variation, wake turbulence, and bottom contact to stabilize otter board motion.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 B
• /
• pp.600-602
• /
• 1995

The paper presents neural network control techniques for load frequency control of two area power system. Using learning algorithm of error back propagation after learning accept input on the optimal control $e_{i}$, $\dot{e}_{i}$, and $u_{i}$ frequency characteristic and tie-line load flow characteristic investigated dynamic. From result simulation, frequency deviation and tie-line load flow deviation have reduction remarkable.

• 설비공학논문집
• /
• 제3권4호
• /
• pp.215-221
• /
• 1991

Laminar film condensation of a saturated vapor in forced flow over a flat plate is analyzed by using integral method. Laminar condensate film is so thin that the inertia and thermal convection terms in liquid flow can be neglected. Approximate solutions for water are presented and well agreed with the similarity solutions over the wide range of physical parameter, Cp1(Ts-Tw)/Pr.hfg. For the strong condensation case, it is found that magnitude of the interfacial shear stress at the liquid-vapor interphase boundary is approximately equal to the momentum transferred by condensation, i.e., ${\tau}_i{\simeq}\dot{m}(U_O-U_i)$.

• Korea-Australia Rheology Journal
• /
• 제21권4호
• /
• pp.213-223
• /
• 2009

Taylor-Couette flow (i.e., flow between concentric, rotating cylinders) has long served as a paradigm for studies of hydrodynamic stability. For Newtonian fluids, the rich cascade of transitions from laminar, Couette flow to turbulent flow occurs through a set of well-characterized flow states (Taylor Vortex Flow, wavy Taylor vortices, modulated wavy vortices, etc.) that depend on the Reynolds numbers of both the inner and outer cylinders ($Re_i$ and $Re_o$). While extensive work has been done on (a) the effects of weak viscoelasticity on the first few transitions for $Re_o=0$ and (b) the effects of strong viscoelasticity in the limit of vanishing inertia ($Re_i$ and $Re_o$ both vanishing), the viscoelastic Taylor-Couette problem presents an enormous parameter space, much of which remains completely unexplored. Here we describe our recent experimental efforts to examine the effects of drag reducing polymers on the complete range of flow states observed in the Taylor-Couette problem. Of particular importance in the present work is 1) the rheological characterization of the test solutions via both shear and extensional (CaBER) rheometry, 2) the wide range of parameters examined, including $Re_i$, $Re_o$ and Elasticity number E1, and 3) the use of a consistent, conservative protocol for accessing flow states. We hope that by examining the stability changes for each flow state, we may gain insights into the importance of particular coherent structures in drag reduction, identify simple ways of screening new drag reducing additives, and improve our understanding of the mechanism of drag reduction.