• Journal of Korean Society of Steel Construction
• /
• v.22 no.1
• /
• pp.1-12
• /
• 2010

According to the capacity design concept which forms the basis of the current steel seismic codes, the braces in concentrically braced frames (CBFs) should dissipate seismic energy through cyclic tension yielding and cyclic compression buckling while the beams and the columns should remain elastic. Brace buckling in inverted V-braced frames induces unbalanced vertical forces which, in turn, impose the additional beam moments and column axial forces. However, due to difficulty in predicting the location of buckling stories, the most conservative approach implied in the design code is to estimate the column axial forces by adding all the unbalanced vertical forces in the upper stories. One alternative approach, less conservative and recommended by the current code, is to estimate the column axial forces based on the amplified seismic load expected at the mechanism-level response. Both are either too conservative or lacking technical foundation. In this paper, three combination rules for a rational estimation of the column axial forces were proposed. The idea central to the three methods is to detect the stories of high buckling potential based on pushover analysis and dynamic behavior. The unbalanced vertical forces in the stories detected as high buckling potential are summed in a linear manner while those in other stories are combined by following the SRSS(square root of sum of squares) rule. The accuracy and design advantage of the three methods were validated by comparing extensive inelastic dynamic analysis results. The mode-shape based method(MSBM), which is both simple and accurate, is recommended as the method of choice for practicing engineers among the three.

• Journal of KIISE:Computer Systems and Theory
• /
• v.34 no.5_6
• /
• pp.257-266
• /
• 2007

In On-Chip bus, the arbitration scheme is one of the critical factors that decide the overall system performance. The arbitration scheme used in traditional shared bus is the master-side arbitration based on the request and grant signals between multiple masters and single arbiter. In the case of the master-side arbitration, only one master and one slave can transfer the data at a time. Therefore the throughput of total bus system and the utilization of resources are decreased in the master-side arbitration. However in the slave-side arbitration, there is an arbiter at each slave port and the master just starts a transaction and waits for the slave response to proceed to the next transfer. Thus, the unit of arbitration can be a transaction or a transfer. Besides the throughput of total bus system and the utilization of resources are increased since the multiple masters can simultaneously perform transfers with independent slaves. In this paper, we implement and analyze the arbitration schemes for the Multi-Layer AHB BusMatrix based on the slave-side arbitration. We implement the slave-side arbitration schemes based on fixed priority, round robin and dynamic priority and accomplish the performance simulation to compare and analyze the performance of each arbitration scheme according to the characteristics of the master and slave. With the performance simulation, we observed that when there are few masters on critical path in a bus system, the arbitration scheme based on dynamic priority shows the maximum performance and in other cases, the arbitration scheme based on round robin shows the highest performance. In addition, the arbitration scheme with transaction based multiplexing shows higher performance than the same arbitration scheme with single transfer based switching in an application with frequent accesses to the long latency devices or memories such as SDRAM. The improvements of the arbitration scheme with transaction based multiplexing are 26%, 42% and 51%, respectively when the latency times of SDRAM are 1, 2 and 3 clock cycles.

• Journal of Broadcast Engineering
• /
• v.8 no.4
• /
• pp.325-338
• /
• 2003

Video adaptation in response to dynamic resource conditions and user preferences is required as a key technology to enable universal multimedia access (UMA) through heterogeneous networks by a multitude of devices In a seamless way. Although many adaptation techniques exist, selections of appropriate adaptations among multiple choices that would satisfy given constraints are often ad hoc. To provide a systematic solution, we present a general conceptual framework to model video entity, adaptation, resource, utility, and relations among them. It allows for formulation of various adaptation problems as resource-constrained utility maximization. We apply the framework to a practical case of dynamic bit rate adaptation of MPEG-4 video streams by employing combination of frame dropping and DCT coefficient dropping. Furthermore, we present a descriptor, which has been accepted as a part of MPEG-21 Digital Item Adaptation (DIA), for supporting terminal and network quality of service (QoS) in an interoperable manner. Experiments are presented to demonstrate the feasibility of the presented framework using the descriptor.

• Journal of Intelligence and Information Systems
• /
• v.21 no.2
• /
• pp.151-171
• /
• 2015

This study examined the concepts of the Internet of Things(IoT), the major issue and IoT trend in the domestic and international market. also reviewed the advent of IoT era which caused a 'Paradigm Shift'. This study proposed a solution for the appropriate corresponding strategy in terms of Enterprise. Global competition began in the IoT market. So, Businesses to be competitive and responsive, the government's efforts, as well as the efforts of companies themselves is needed. In particular, in order to cope with the dynamic environment appropriately, faster and more efficient strategy is required. In other words, proposed a management strategy that can respond the IoT competitive era on tipping point through the vision of paradigm shift. We forecasted and proposed the emergence of paradigm shift through a comparative analysis of past management paradigm and IoT management paradigm as follow; I) Knowledge & learning oriented management, II) Technology & innovation oriented management, III) Demand driven management, IV) Global collaboration management. The Knowledge & learning oriented management paradigm is expected to be a new management paradigm due to the development of IT technology development and information processing technology. In addition to the rapid development such as IT infrastructure and processing of data, storage, knowledge sharing and learning has become more important. Currently Hardware-oriented management paradigm will be changed to the software-oriented paradigm. In particular, the software and platform market is a key component of the IoT ecosystem, has been estimated to be led by Technology & innovation oriented management. In 2011, Gartner announced the concept of "Demand-Driven Value Networks(DDVN)", DDVN emphasizes value of the whole of the network. Therefore, Demand driven management paradigm is creating demand for advanced process, not the process corresponding to the demand simply. Global collaboration management paradigm create the value creation through the fusion between technology, between countries, between industries. In particular, cooperation between enterprises that has financial resources and brand power and venture companies with creative ideas and technical will generate positive synergies. Through this, The large enterprises and small companies that can be win-win environment would be built. Cope with the a paradigm shift and to establish a management strategy of Enterprise process, this study utilized the 'RTE cyclone model' which proposed by Gartner. RTE concept consists of three stages, Lead, Operate, Manage. The Lead stage is utilizing capital to strengthen the business competitiveness. This stages has the goal of linking to external stimuli strategy development, also Execute the business strategy of the company for capital and investment activities and environmental changes. Manege stage is to respond appropriately to threats and internalize the goals of the enterprise. Operate stage proceeds to action for increasing the efficiency of the services across the enterprise, also achieve the integration and simplification of the process, with real-time data capture. RTE(Real Time Enterprise) concept has the value for practical use with the management strategy. Appropriately applied in this study, we propose a 'IoT-RTE Cyclone model' which emphasizes the agility of the enterprise. In addition, based on the real-time monitoring, analysis, act through IT and IoT technology. 'IoT-RTE Cyclone model' that could integrate the business processes of the enterprise each sector and support the overall service. therefore the model be used as an effective response strategy for Enterprise. In particular, IoT-RTE Cyclone Model is to respond to external events, waste elements are removed according to the process is repeated. Therefore, it is possible to model the operation of the process more efficient and agile. This IoT-RTE Cyclone Model can be used as an effective response strategy of the enterprise in terms of IoT era of rapidly changing because it supports the overall service of the enterprise. When this model leverages a collaborative system among enterprises it expects breakthrough cost savings through competitiveness, global lead time, minimizing duplication.

• The Korean Journal of Physiology
• /
• v.24 no.1
• /
• pp.181-194
• /
• 1990

Antidromically activated spinoreticular tract (SRT) cell units in the lumbosacral enlargement of ${\alpha}-chloralose$ anesthetized cats were classified as medial and lateral SRT units according to the location of their axonal termination. Identified SRT units were tested fer antidromic conduction velocity, laterality of their axonal projection, the location in spinal gray, peripheral receptive field, the response pattern to graded mechanichal stimulation and the responsiveness to $A{\delta}$ and C volley of the peripheral nerve. 1) The 59% of 34 medial SRT units were recorded in ipsilateral side to the antidromic stimulation site, but 60% of the 47 lateral SRT units projected to contralateral side. 2) Most of the medial SRT cells and rostral ventrolateral medulla (RVLM)-projecting lateral SRT cells were recorded in lamina VII & VIII. The LRN (lateral reticular nucleus)-projecting SRT cells, however, distributed through all the laminae except superficial ones (I & II). 3) The identified SRT units were classified as low theshold (LT), deep, high threshold (HT), wide dynamic range (WDR) cells, based on the response patterns to graded mechanical stimuli. The proportion of SRT units which receive noxious input was 37.5%, 25% and 75% in the medial, LRN-projecting and RVLM SRT group, respectively. 4) There was no significant difference in the mean conduction velocities between the 3 groups. But the deep cells had significantly higher velocity than that of the HT cells. The above results show that the peripheral inputs to the SRT units are different in the 3 groups: medial, LRN & RVLM SRT group. Especially in case of the SRT cells projecting to RVLM which is a probable candidate fur the integration center of various pressor reflexes such as somatosympathetic reflex, the noxious informations occupy higher proportion of input to them than in other groups. Therefore the noxious information transmitted through the lateral SRT destined for RVLM is expected to play a role in somatosymapthetic reflex.

• Korean Journal of Ecology and Environment
• /
• v.41 no.3
• /
• pp.348-359
• /
• 2008

The objectives of the study were to elucidate functional modifications in relation to hydrological, physico-chemical and ecological aspects in Daechung Reservoir by the upper dam constructions of Youngdam Reservoir and analyze temporal and spatial dynamic patterns using trophic parameters of TN, TP, chlorophyll (CHL), and Secchi depth (SD). Hydrological data such as inflow, precipitation, and water levels before (BDC, 1995$\sim$2000) and after (ADC, 2001$\sim$2006) the dam construction showed that precipitation had greater correlations with inflow volume in the BDC (r=0.964, p=0.002) than in the ADC (r=0.857, p=0.029). This outcome indicates that the upper dam construction influenced the inflow and water level of Daechung Reservoir. One of the greatest changes after the dam construction was decreases of nutrient contents (TN, TP) and increases of algal biomass (as CHL) as the water residence time increases. Values of CHL had greater relations with TP in the ADC (r=0.412, p<0.001) than the BDC (r=0.249, p<0.001), indicating that CHL had greater response at a given phosphorus in the ADC. Thus, algal yield at a given TP (CHL : TP ratios) increased in the ADC, resulting in a greater CHL-TP relations. Long-term interannual TP, TN, SD, and CHL showed greater variations in the riverine zone (RZ) than any other transition (TZ) and lacustrine zones (LZ). This phenomenon was mainly attributed to rapid hydrological response in the riverine zone (RZ) to flow reductions (short water residence time) from the upper dam, resulting in ambient contents of nutrients and light regime along with functional relations of CHL-TP.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.6
• /
• pp.98-105
• /
• 2017

In this study, the fiber blending ratio and strain rate effect on the tensile behavior of hybrid fiber reinforced cement composite was evaluated. Hooked steel fiber and polyvinyl alcohol fiber were used for reinforcing fiber. The fiber blending ratio of HSF+PVA were 1.5+0.5, 1.0+1.0 and 0.5+1.5vol.%. As a results, the tensile strength, strain capacity and fracture toughness of the hooked steel fiber reinforced cement composites were improved by the increase of the bond strength of the fiber and the matrix according to increase of strain rate. However, the tensile stress sharply decreased after the peak stress because of the decrease in the number of straightened pull-out fibers by micro cracks in the matrix around hooked steel fiber. On the other hand, PVA fiber showed cut-off fracture at strain rate $10^{-6}/s$ with multiple cracks. However, at the strain rate $10^1/s$, the multiple cracks and strain capacity were decreased because of the pull-out fracture of PVA fiber. The HSF1.5PVA0.5 shown the highest tensile strength because the PVA fiber suppressed the micro cracks in the matrix around the hooked steel fiber and improved the pull-out resistance of hooked steel fiber. Thus, DIF of strain capacity and fracture toughness of HSF1.5PVA were greatly improved. In addition, the synergistic response of fracture toughness was positive because the tensile stress was slowly decreased after the peak stress by improvement of the pull-out resistance of hooked steel fiber at strain rate $10^1/s$.

• Journal of Arbitration Studies
• /
• v.15 no.2
• /
• pp.3-35
• /
• 2005

The meaning of Online ADR lies in the prompt and economical resolution of disputes by applying the information/communication element (Internet) to existing ADR. However, if the promptness and economical efficiency are overemphasized, the fairness and appropriateness of dispute resolution may be compromised and consequently Online ADR will be belittled and criticized as second-class trials. In addition, as communication is mostly made using texts in Online ADR it is difficult to investigate cases and to create atmosphere and induce dynamic feelings, which are possible in the process of dispute resolution through face-to-face contact. Despite such difficulties, Online ADR is expanding its area not only in online but also in offline due to its advantages such as promptness, low expenses and improved resolution methods, and is expected to develop rapidly as the electronic government decided to adopt it in the future. Accordingly, the following points must be focused on for the continuous First, in the legal and institutional aspects for the development of Online ADR, it is necessary to establish a framework law on ADR. A framework law on ADR comprehending existing mediation and arbitration should be established and it must include contents of Online ADR, which utilizes electronic communication means. However, it is too early to establish a separate law for Online ADR because Online ADR must develop based on the theoretical system of ADR. Second, although Online ADR is expanding rapidly, it may take time to be settled as a tool of dispute resolution. As discussed earlier, additionally, if the amount of money in dispute is large or the dispute is complicated, Online ADR may have a negative effect on the resolution of the dispute. Thus, it is necessary to apply Online ADR to trifle cases or domestic cases in the early stage, accumulating experiences and correcting errors. Moreover, in order to settle numerous disputes effectively, Online ADR cases should be analyzed systematically and cases should be classified by type so that similar disputes may be settled automatically. What is more, these requirements should reflected in developing Online ADR system. Third, the application of Online ADR is being expanded to consumer disputes, domain name disputes, commercial disputes, legal disputes, etc., millions of cases are settled through Online ADR, and 115 Online ADR sites are in operation throughout the world. Thus Online ADR requires not temporary but continuous attention, and mediators and arbitrators participating in Online ADR should be more intensively educated on negotiation and information technologies. In particular, government-led research projects should be promoted to establish Online ADR model and these projects should be supported by comprehensive researches on mediation, arbitration and Online ADR. Fourth, what is most important in the continuous development and expansion of Online ADR is to secure confidence in Online ADR and advertise Online ADR to users. For this, incentives and rewards should be given to specialists such as lawyers when they participate in Online ADR as mediators and arbitrators in order to improve their expertise. What is more, from the early stage, the government and public institutions should have initiative in promoting Online ADR so that parties involved in disputes recognize the substantial contribution of Online ADR to dispute resolution. Lastly, dispute resolution through Online ADR is performed by organizations such as Korea Institute for Electronic Commerce and Korea Consumer Protection Board and partially by Korean Commercial Arbitration Board. Online ADR is expected to expand its area to commercial disputes in offline in the future. In response to this, Korean Commercial Arbitration Board, which is an organization for commercial dispute resolution, needs to be restructured.

• Journal of Intelligence and Information Systems
• /
• v.17 no.4
• /
• pp.109-130
• /
• 2011

One of the major problems in the area of data mining is the size of the data, as most data set has huge volume these days. Streams of data are normally accumulated into data storages or databases. Transactions in internet, mobile devices and ubiquitous environment produce streams of data continuously. Some data set are just buried un-used inside huge data storage due to its huge size. Some data set is quickly lost as soon as it is created as it is not saved due to many reasons. How to use this large size data and to use data on stream efficiently are challenging questions in the study of data mining. Stream data is a data set that is accumulated to the data storage from a data source continuously. The size of this data set, in many cases, becomes increasingly large over time. To mine information from this massive data, it takes too many resources such as storage, money and time. These unique characteristics of the stream data make it difficult and expensive to store all the stream data sets accumulated over time. Otherwise, if one uses only recent or partial of data to mine information or pattern, there can be losses of valuable information, which can be useful. To avoid these problems, this study suggests a method efficiently accumulates information or patterns in the form of rule set over time. A rule set is mined from a data set in stream and this rule set is accumulated into a master rule set storage, which is also a model for real-time decision making. One of the main advantages of this method is that it takes much smaller storage space compared to the traditional method, which saves the whole data set. Another advantage of using this method is that the accumulated rule set is used as a prediction model. Prompt response to the request from users is possible anytime as the rule set is ready anytime to be used to make decisions. This makes real-time decision making possible, which is the greatest advantage of this method. Based on theories of ensemble approaches, combination of many different models can produce better prediction model in performance. The consolidated rule set actually covers all the data set while the traditional sampling approach only covers part of the whole data set. This study uses a stock market data that has a heterogeneous data set as the characteristic of data varies over time. The indexes in stock market data can fluctuate in different situations whenever there is an event influencing the stock market index. Therefore the variance of the values in each variable is large compared to that of the homogeneous data set. Prediction with heterogeneous data set is naturally much more difficult, compared to that of homogeneous data set as it is more difficult to predict in unpredictable situation. This study tests two general mining approaches and compare prediction performances of these two suggested methods with the method we suggest in this study. The first approach is inducing a rule set from the recent data set to predict new data set. The seocnd one is inducing a rule set from all the data which have been accumulated from the beginning every time one has to predict new data set. We found neither of these two is as good as the method of accumulated rule set in its performance. Furthermore, the study shows experiments with different prediction models. The first approach is building a prediction model only with more important rule sets and the second approach is the method using all the rule sets by assigning weights on the rules based on their performance. The second approach shows better performance compared to the first one. The experiments also show that the suggested method in this study can be an efficient approach for mining information and pattern with stream data. This method has a limitation of bounding its application to stock market data. More dynamic real-time steam data set is desirable for the application of this method. There is also another problem in this study. When the number of rules is increasing over time, it has to manage special rules such as redundant rules or conflicting rules efficiently.

• The Korean Journal of Malacology
• /
• v.21 no.2 s.34
• /
• pp.121-132
• /
• 2005

We investigated the reproductive cycle with gonad developmental phases of Sinonovacula constricta by histological observations, and seasonal changes in biochemical component of the adductor muscle, visceral mass, foot muscle and mantle were studied by biochemical analysis, from January to December, 2004. The reproductive cycle of this species can be classifed into five successive stages: early active stage (March to May), late active stage (May to July), ripe stage (July to September), partially spawned stage (August to October) and spentfinactive stage (October to March). Total protein content was the highest in the following order: adductor muscle, visceral mass, foot muscle, and mantle. Except for mantle, it was generally higher during the ripe and spawning stages, while lower during the spent/inactive stage. There were positive correlations in total protein contents among adductor muscle, foot muscle, and visceral mass. However, the correlations were not statistically significant. Total lipid content was the highest in the visceral mass; it was more than 5 or 6-fold higher than those in the adductor muscle, foot muscle, or mantle. The monthly change was also most dynamic in the visceral mass. It first Increased during the early active stage (March to May), decreased during late active stage (May to July), and then increased again rapidly during the spawning stage (September). There were a strong negative correlation in total lipid contents between foot muscle and adductor muscle (r = -0.634, p = 0.027), and a strong positive correlation between adductor muscle and mantle (r = 0.665, p = 0.018). Glycogen contents showed more or less similar pattern to total lipid contents in the adductor muscle, foot muscle, and visceral mass. It was higher during the early active and spawning stages, while lower during the late active and spent/inactive stages. There was no statistically significant correlation in glycogen contents among different tissues. Especially, total lipid content showed a negative correlationship between the foot muscle, adductor muscle, visceral mass and mantle. Therefore, these results indicate that the nutrient content of the foot muscle, adductor muscle, viseral mass and mantle changed in response to gonadal energy needs.