• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1006-1011
• /
• 2008

The objective of this study is the developement of real time automatic dynamic measurement using high accuracy digital datalogger for safety and maintence of railway construction sites. For the replacement of current 16 bit analog/digital converter, Digital datalogger system using 24 bit analog/digital converter is studied for the first time with in a country. Therefore data communication method and analyzing program of automatic measurement data is developed for the automatic high accuracy digital datalogger system. The results of this study will be using real time automatic dynamic measurement of railway structures.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.3
• /
• pp.106-111
• /
• 2023

The importance of load-to-use latency has been highlighted as state-of-the-art computing cores adopt deep pipelines and high clock frequencies. The cascaded cache was recently proposed to reduce the access cycle of the L1 cache by utilizing differences in latencies among banks of the cache structure. However, this study assumes the cache is comprised of SRAM, making it unsuitable for direct application to non-volatile memory-based systems. This paper proposes a novel mechanism and structure for lowering dynamic energy consumption. It inserts monitoring logic to keep track of swap operations and write counts. If the ratio of swap operations to total write counts surpasses a set threshold, the cache controller skips the swap of cache blocks, which leads to reducing write operations. To validate this approach, experiments are conducted on the non-volatile memory-based cascaded cache. The results show a reduction in write operations by an average of 16.7% with a negligible increase in latencies.

• Journal of the Korea Institute of Building Construction
• /
• v.6 no.2 s.20
• /
• pp.73-79
• /
• 2006

The purpose of this study is to enhance the development of construction waste-recycling technologies and its economical efficiency by developing environment-friendly tetrapod, precast concrete, where recycled aggregate is used in order to promote recycling of waste concrete. The results of concrete mechanic characteristics experiments by the circulation coarse aggregate-replacement ratio are as the following. The circulation aggregate is lower and higher than natural aggregate in specific gravity and absorption ratio, respectively so that in case of mix proportioning, unit volume increases, while unit aggregate amount decreases. From the result, sufficient experiments of physical characteristics of circulation aggregate are required to get proper mix proportioning. When circulation aggregate-replacement ratio increases, compressive strength tends to decrease comprehensively, but 50% of replacement ratio is good enough to use. When circulation coarse aggregate's replacement ratio is 0%, drying shrinkage, which causes cracks in concrete and deteriorates durability, shows the minimum length change and the higher the ratio, the larger the length change. Thus. when using circulation coarse aggregate, drying shrinkage should be fairly examined. In freezing-and-thawing resistance, weight loss tends to comprehensively increase its loss at the circulation aggregate-mixed site. And the examination of surface aggregate-omission ratio is further needed and dynamic elastic modulus and durability factor(DF) require more study as well. In order to use circulation aggregate to tetrapod, a clear standard for strength should be first prepared and at the same time, more study about durability is needed.

• Journal of the Korean Orthopaedic Association
• /
• v.54 no.5
• /
• pp.377-383
• /
• 2019

The biomechanics study of the hip is aims to understand and explore the dynamic principles of weight transfer through the hip joint. This basic science knowledge can be applied in a variety of areas, including degenerative joint diseases and hip replacement arthroplasty. In particular, understanding of the biomechanics of the hip has led to the development of materials, design and fixation of implants, and it can be applied in various areas, such as the selection of surgical methods and the location of the implant. Moreover, it is essential to have good knowledge of the biomechanics of the hip to achieve better clinical results for patients. Therefore, this paper introduces the basic knowledge and biomechanical characteristics of a normal hip and hip replacement arthroplasty, which are needed to approach the biomechanics of the hip.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.9 no.1 s.41
• /
• pp.43-50
• /
• 2005

Many highway bridges in Korea need seismic retrofit because only one decade has passed since the seismic design criteria was introduced. For the highway bridges of which bearings are worn and dysfunctional, the validity of seismic retrofit method using laminated rubber bearings was discussed in this study. Real scale RC pier specimens without seismic details were constructed. And then, Pot bearing, Rubber bearing (RB), Lead-rubber bearing (LRB) were applied to these specimens. Through pseudo dynamic test method, dynamic behavior of these RC piers under earthquake was simulated and compared. From the test results, proposed seismic retrofit method was found to be valid.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.12
• /
• pp.923-929
• /
• 2003

As for the marine propulsion shafting system using 4 stroke diesel engine, it is common to apply a reduction gear box between diesel engine and shafting to increase propulsion efficiency, which requires inevitably a certain elastic coupling to avoid chattering and hammering inside of gear box. In this study, the optimum method of rectifying propulsion shafting system in case of 750 ton fishing vessel is theoretically studied in a view of dynamic characteristics of torsion. After the replacement of diesel engine and gear box, the torsional vibration get worse and so some countermeasures are needed. The elastic coupling is modified from a present rubber coupling of block type having relatively high torsional stiffness to a rubber coupling haying two serially connected elements. Torsional vibration damper was installed at crankshaft free end additionally and moment of inertia of flywheel was adjusted. The dynamic characteristics of shafting system was improved by these modification. The theoretical analysis of torsional vibration are compared to measurement results using two laser torsion meters during the sea trial.

• Nuclear Engineering and Technology
• /
• v.56 no.5
• /
• pp.1863-1873
• /
• 2024

In the Korean domestic nuclear industry, to analyze the reliability of instrumentation and control (I&C) systems, the failure rates of the electronic components constituting the I&C systems are predicted based on the MIL-HDBK-217F standard titled 'Reliability Prediction of Electronic Equipment'. Based on these predicted failure rates, the mean time to failure of the I&C systems is calculated to determine the replacement period of the I&C systems. However, this conventional approach to the prediction of electronic component failure rates assumes that factors affecting the failure rates such as ambient temperature and operating voltage are static constants. In this regard, the objective of this study is to propose a prediction method for the remaining useful life (RUL) of electronic components considering mean time to failure calculations reflecting dynamic environments, such as changes in ambient temperature and operating voltage. Results of this study show that the RUL of electronic components can be estimated depending on time-varying temperature and electrical stress, implying that the RUL of electronic components can be predicted under dynamic stress conditions.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.11a
• /
• pp.15-16
• /
• 2015

Natural stone causes environmental pollution when it is collected and processed. Also, it is hard to make consistent products. Therefore, this study focuses on the artificial stone with waste porcelain to replace natural stone. The flexural strength and compressive strength are lower according to the replacement ratio of blast furnace slag in the result of experiment.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.4
• /
• pp.7-13
• /
• 1998

The gloval model is developed by combining this actuator formular with robot manipulator which is reported previously . The model initially represented in the form of coupled time-varying nonlinear dynamic system. It then decomposed into the decoupled linear model using nonlinear feedback and state transformation techniques. The new model employes the pole replacement method to improve the stability of the system. Using this new model, an robust control algorithm is developed. The proposed algorithm takes two state variables, position vector and velocity vector, and one input variable from actuator, input voltage.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.15 no.5
• /
• pp.623-629
• /
• 2012

In this paper, we analysis the performance of position estimation when adopting Dynamic TDMA(DTDMA) in JTIDS RelNav. JTIDS RelNav is widely understood as a new navigation solution possibly capable to support or take cover of the role of conventional systems including INS or GPS no matter if they are working well or not. By maximizing the efficiency of radio resource management in MAC(Medium Access Control) layer we enhance the system performance without any replacement of hardware.